Part No. 902400 Model IM250A Li ED L G ER N A IL E A G N U H A G INIS 6 F 1 S N S -IO E DL IUM R H CO LIT IMPORTANT! DO NOT DESTROY OPERATING MANUAL It is the customer's responsibility to have all operators and service personnel read and understand this manual. Printed in U.S.A. © 2012 IllinoisTool Works Inc. 902451-1 03/12 www.paslode.
Contents Subject Page Introduction and Warranty ............................................................................................................................................... 2 An Overview of the Paslode Cordless 16 Gauge Angled Lithium-ion Finish Nailer ......................................................... 3 Safety Instructions ...........................................................................................................................................................
Introduction and Warranty Paslode Cordless 16 Gauge Angled Lithium-ion Finish Nailer Operating Manual This manual is intended to acquaint you with the Paslode Cordless 16 ga. Angled Lithium-ion Finish Nailer. Unlike other power fastening tools, the Cordless Finish Nailer is powered by an internal combustion linear motor. In simpler terms, your Cordless Finish Nailer is powered by a motor similar to the one that powers an automobile.
Overview of the Paslode Cordless 16 Gauge Angled Lithium-ion Finish Nailer Description Specifications The Paslode Cordless 16 ga. Angled Lithium-ion Finish Nailer is a self-contained, fully portable nailer that uses liquid hydrocarbon fuel to power a unique linear drive internal combustion motor. In order for you to fully understand the information contained in this manual, you need a basic understanding of the Cordless Finish Nailer.
Safety Instructions The following safety instructions have been included in this booklet to provide you with basic information necessary for safe operation of the Paslode Cordless 16 ga. Angled Lithium-ion Finish Nailer. DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND MANUAL INSTRUCTIONS. DANGER The Cordless Finish Nailer is an internal combustion device. It produces hot exhaust gases that may ignite flammable materials.
Safety Instructions WARNING 7. NEVER OPERATE THE TOOL WITH THE WORK CONTACTING ELEMENT REMOVED OR DISABLED. Always wear EYE and EAR safety gear when working with or in the vicinity of the Paslode Cordless 16 ga. Angled Lithium-ion Finish Nailer. This device helps reduce the possibility of accidental fastener discharge by preventing the tool from operating until it is completely against the work surface. NEVER operate the tool if the work contacting element is not working properly. 8. 1.
Safety Instructions 12. NEVER DRIVE FASTENERS INTO AREAS WITH CONCEALED HAZARDS. Always check the area behind the work surface for electrical wiring, gas pipes, water pipes, sewer drains or other potential hazards. 13. ALWAYS MAINTAIN SECURE AND UNOBSTRUCTED FOOTING WHEN ON LADDERS, PLATFORMS OR OTHER HIGH LOCATIONS. 15. PROPERLY STORE FUEL CELL. WARNING Always store fuel cartridges where they will not be exposed to an open flame, sparks or temperatures above 120° F (49° C).
Battery and Charging System Battery and Charging System Charging Instructions The Paslode Cordless16 Gauage Angled Lithium-ion Finish Nailer comes with a rechargeable battery and its own charging system. This charging system is the only one that will work with the Paslode lithium-ion batteries. The first step in preparing a new tool for operation is to fully charge the battery. New batteries are shipped partially discharged and must be charged prior to first use.
Battery and Charging System Battery Indicator Light On the right side of the handle is a small plastic lens. This is the battery indicator light. When you insert a fully-charged battery into the tool, you will see a blinking green light. If the indicator light blinks red, recharge the battery. ! TOO L OPE RAT ! ASSU ! READ ME TOO ORS AND MANUAL BYSTAND ! CAR BON MON L IS ALW FROM ERS AYS ! EXPL COVER OSION OXIDE HAZ LOADED MUST WEA TO COV R EYE AND LEA TOD HAZARD ARD ER.
Fuel Cartridge Fuel Cartridge DANGER EXPLOSION/FIRE HAZARD R ead ALL sa f ety instructions before using or handling the fuel cartridge. Failure to follow ALL instructions may result in explosion or fire. This may cause severe personal inj u r i e s o r prop erty damage. Keep the fuel cartridge away from heat, sparks and open flame. There is a second container inside the fuel cartridge. The inner container holds the fuel.
Fuel Cartridge NOTE: Paslode Cordless fuel cartridges are marked with a “Best Use Before” date on the bottom of the can. For maximum performance use fuel before the “Best Use Before” date. DANGER Paslode Cordless Fuel Cartridges are flammable.
Fuel Ca rtridge Inserting Fuel Cartridge A. When loading a fuel cartridge, lift the tool off of the work C. Release the adaptor so it is centered on the fuel surface so the work contact element (WCE) is not depres- cartridge. sed. Press forward at the back of the actuator cover and pivot outward to open. The cover will swing out of the way. 2. PULL OUT 1. PRESS UP ➔ B. Lift the fuel cartridge adaptor and insert the fuel cartridge into the tool. D.
Preparing the Paslode Cordless 16 Gauge Angled Lithium-ion Finish Nailer for Use Fasteners The Paslode Cordless 16 ga. Angled Lithium-ion Finish Nailer drives Paslode® 16 gauge angled fasteners designed to be used with the tool. The use of fasteners that do not meet Paslode standards could cause tool damage and will void all warranty claims. Loading Fasteners STEP 1: Align the heads of the Paslode 16 ga.
Paslode Cordless 16 ga. Angled Lithium-ion Finish Nailer Operation Operation: PRESS WORK – CONTACTING ELEMENT AGAINST THE WORK SURFACE. ➔ Fan motor starts, fuel is injected into combustion chamber and mixed with air by the fan. SQUEEZE TRIGGER Spark plug ignites the fuel/air mixture driving the piston assembly down on the fastener. Turn adjustment wheel in either direction Depth of Drive Adjustment Remove the battery before adjusting the depth of drive.
Fasteners and Applications Applications The Paslode Cordless 16 ga. Angled Finish Nailer is suited for a variety of applications. These include securing door and window casings; attaching baseboards where walls meet floors; attaching moldings where walls meet ceilings; securing paneling; securing chair rails, picture molding and other decorative trim. Fasteners The Paslode Cordless 16 ga. Angled Finish Nailer drives Paslode 16 Gauge Angled Finish Nails.
Servicing Restrict Field Service to the Following CHECKING THE ENERGY LEVEL OF THE BATTERY RECHARGING THE BATTERY CHECKING THE FUEL CARTRIDGE REPLACING THE FUEL CARTRIDGE CLEANING/REPLACING THE AIR FILTER CLEARING A JAM Fuel Cartridge Check If the Cordless Finish Nailer's fan operates and the indicator light is green, but the tool will not cycle or does not drive fasteners completely, check the fuel cartridge.
Servicing Air Filter When you get home: Open the grille by pressing slightly above the adapter and pivoting the cover open. The air filter simply lifts out. 1. Place the battery in its charger if it needs charging as indicated by the red charge light on the handle. Tap the filter GENTLY to remove any dust. Check and clean the air filter every two days. Soap and water restores the filter to a "like new" condition. 2. Wipe your Cordless Finish Nailer with a clean, soft cloth. 3.
Troubleshooting Preparing Tool for Operation - Battery/Charger Problems SYMPTOM Battery does not appear to accept charge when battery is plugged into the charger. Charger gets hot, makes excessively loud noise, or smokes during charging cycle. Charger cord or wall plug gets hot. POSSIBLE PROBLEMS SERVICE Inoperative indicator lights on charger, or defective charger. Try battery in tool after a full charge cycle. If tools indicator light is red, charger not working properly.
Troubleshooting Normal Stage of Operation SYMPTOM Tool operates properly, but fasteners do not drive fully. Tool operates properly, but fasteners are sometimes over-driven, and sometimes under-driven. POSSIBLE PROBLEMS Work-contacting element requires adjustment. Adjust work contacting element. Fuel cell is low. Check fuel cell and replace as required. There may be loss of seal in combustion chamber. Press work contacting element against workpiece for one minute. Pull trigger.
