Model CF-325 9 21 902245-3 01/09
Introduction and Warranty Paslode Cordless Framing Nailer Operating Manual This manual is intended to acquaint you with the Paslode Cordless Framing Nailer. Unlike other power fastening tools, the Cordless Framing Nailer is powered by an internal combustion linear motor. In simpler terms, your Cordless Framing Nailer is powered by a motor similar to the one that powers an automobile.
Contents Subject Page Introduction and Warranty ......................................................... 2 An Overview of the Paslode Cordless Framing Nailer ...............4 Safety Instructions......................................................................5 Battery and Charging System ................................................... 8 Fuel Cell and Metering Valve .................................................. 10 Preparing the Paslode Cordless Framing Nailer for Use .........
An Overview of the Paslode Cordless Framing Nailer Description Specifications The Paslode Cordless Framing Nailer is a self-contained, fully portable nailer that uses liquid hydrocarbon fuel to power a unique linear drive internal combustion motor. As with any internal combustion motor, the Paslode Cordless Nailer will require periodic maintenance to keep it operating at it's peak performance. The cleaning procedure booklet will instruct you on the proper cleaning of your tool.
Safety Instructions The following safety instructions have been included in this booklet to provide you with basic information necessary for safe operation of the Paslode Cordless Framing Nailer. DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND MANUAL INSTRUCTIONS. In addition to these instructions, training may be necessary. Contact your Paslode representative for additional information.
Safety Instructions WARNING EYE and EAR safety gear must be worn when working with or in the vicinity of the Paslode Cordless Framing Nailer. 1. Eye protection must meet the requirements of ANSI Standard Z87.1 and should have side shields for increased protection. As an employer you are responsible for enforcing the use of eye protection equipment by the tool operator and all personnel in the work area. 7. NEVER OPERATE THE TOOL WITH THE WORK CONTACTING ELEMENT REMOVED OR DISABLED.
Safety Instructions 12. NEVER DRIVE FASTENERS INTO AREAS WITH CONCEALED HAZARDS. Always check the area behind the work surface for electrical wiring, gas pipes, water pipes, sewer drains or other potential hazards. 13. ALWAYS MAINTAIN SECURE AND UNOBSTRUCTED FOOTING WHEN ON LADDERS, PLATFORMS OR OTHER HIGH LOCATIONS. 15. PROPERLY STORE FUEL CELL. WARNING Always store tool, fuel cartridge and battery where they will not be exposed to an open flame, sparks or temperatures above 120° F (49° C).
Battery And Charging System The Paslode Cordless tool comes with a rechargeable battery and its own charging system. This charging system is the only one that will work with all Paslode batteries (round or oval). It will accept either the round or oval shaped batteries. The first step in preparing a new tool for operation is to fully charge the battery. New batteries are shipped discharged and must be charged prior to first use.
Battery and Charging System Battery Indicator Light The illustration is a close-up of the side of the Paslode Cordless framer handle. On the side of the handle is a small plastic lens. This is the battery indicator light. When you insert a fully-charged battery into the tool, you will see a blinking green light. If the light blinks red, recharge the battery. Battery Indicator Light Inserting Battery 1. Load the battery, contacts first, into Framing Nailer. the Cordless 2.
Quicklode™ Fuel Cartridge Fuel Cartridge WARNING EXPLOSION/FIRE HAZARD Read ALL safety instructions before using or handling the fuel cell. Failure to follow ALL instructions may result in explosion or fire. This may cause serious personal injuries or property damage. Keep the fuel cartridge away from heat, sparks and open flame. Do not smoke when handling or operating tool or fuel cartridge. Exposure to temperatures above 120°F (49°C) may cause the fuel cartridge to burst, releasing flammable gas.
Quicklode™ Fuel Cartridge Fuel cartridge cap Best Used By Date NOTE: Paslode Cordless fuel cartridges are marked with a best used by date on the bottom of the can. For maximum performance use fuel before best used by date. DANGER Paslode Cordless Fuel Cartridges are flammable.
Quicklode™ Fuel Cartridge Inserting Fuel Cartridge A. Inserting the fuel cartridge into the Cordless Framing Nailer is very simple. To begin, press up at the bottom of the actuator cover and pivot outward to open. The cover will swing out of the way. C. Release the adaptor so it is centered on the fuel cartridge. 1. Press Up 2. Pull Out B. Lift the fuel cartridge adaptor and insert the Quicklode fuel cartridge into the tool. D.
Preparing the Paslode Cordless Framing Nailer for Use Fasteners The Paslode Cordless Framing Nailer drives Paslode RounDrive® nails, which have been collated into strips. The use of nails that do not meet Paslode standards could cause tool damage and void your warranty. Paslode nail sizes and types are illustrated in the Fasteners and Applications section. Loading Fasteners Lockout Feature The purpose of this feature is to prevent needless blank cycling,which could waste fuel and damage tool components.
Paslode Cordless Framing Nailer Operation PRESS WORK – CONTACTING ELEMENT AGAINST THE WORK SURFACE. Fan motor starts, fuel is injected into combustion chamber and mixed with air by the fan. SQUEEZE TRIGGER Spark plug sparks and fuel/air mixture ignites. Combustion powers piston assembly driving fastener. LIFT TOOL RELEASE TRIGGER Combustion chamber opens. Fan exhausts hot gases and cools internal components.
Fasteners and Applications TYPE APPLICATION 2" x .113 (6D) SIZE Common Ring Shank 2" x .113 (6D) Common ring shank, hot-dipped galvanized plus Underlayment, wall sheathing, roof and floor decking, siding Fencing, siding 2-3/8" x .113 (8D) Cooler ring shank 2-3/4" x .113 (8D) Coated ring shank, hot-dipped galvanized plus 3" x .120 (10D) 3" x .120 (10D) Coated nail Ring shank, hot-dipped galvanized plus Remodeling Fencing, recreational decking, siding, tile roofs 3" x .131 (10D) 3-1/4" x .
Servicing Restrict Field Service to the Following CHECKING THE ENERGY LEVEL OF THE BATTERY RECHARGING THE BATTERY CHECKING THE FUEL CARTRIDGE REPLACING THE FUEL CARTRIDGE CLEANING THE AIR FILTER Fuel Cartridge Check If the Cordless Framing Nailer's fan operates and the light is green, but the tool will not cycle or does not drive fasteners completely, check the fuel cartridge. With the fuel cartridge out of the tool, check to see if the cartridge still contains fuel.
Servicing WARNING Make certain magazine mounting screws are tight and magazine is tight to nose. Attempting to fire tool with a loose magazine will result in loss of nail control, damage to tool, or nail discharge toward operator. Air Filter When you get home: 1. Place the battery in its charger if it needs charging as indicated by the red charge light on the handle. 2. Wipe your Cordless Framing Nailer with a clean, soft cloth. 3. Remove and clean the filter every two days.
Troubleshooting Preparing Tool for Operation - Battery/Charger Problems SYMPTOM POSSIBLE PROBLEMS Battery does not appear to accept charge when the battery and charger are plugged into the wall mount adapter. Inoperative indicator lights on charger, or defective charger. Battery charger flashes red/green for more than 20 minutes. Defective battery. SERVICE Try battery in tool after a full charge cycle. If tool LED is green, charger is not working properly.
Troubleshooting Normal Stage of Operation SYMPTOM Tool operates properly, but fasteners do not drive fully. Tool operates, but no fastener is driven. Tool operates erratically or appears to be losing power - tool indicator light is green. Tool operated and drove fasteners, but driver blade did not return to up position. Combustion chamber does not drop after tool cycles. POSSIBLE PROBLEMS SERVICE Work-contacting element requires adjustment. Adjust work contacting element. Dirty air filter.
P An Illinois Tool Works Company 888 Forest Edge Drive Vernon Hills, Illinois 60061 www.paslode.
