Paslode Model: IM200 F18 Part No. 901000 18 Gauge Finish Nailer 18 GAUGE CORDLESS FINISH NAILER Cleaning Procedure www.paslode.
This procedure provides a simple but effective way to clean your Paslode Cordless tool and maintain reliable operation. Regular cleaning and lubrication will also extend part life and provide maximum nail driving power. Only one tool is necessary to disassemble the Paslode Cordless tool in preparation for cleaning: a 9164" hex key provided with the Paslode Cordless tool. Paslode ® recommends that an aerosol "Degreaser Cleaner", such as Paslode Degreaser Cleaner (Part No. 219086), be used for cleaning.
Step 2 Remove the Cap, Filter, and Grill as one assembly, and set aside. The Filter may be removed by lifting the Grill offthe Cap. Clean the Filter with a mild soap solution, or replace if necessary. Paso 2 Quite la tapa, el filtro y la rejilla como una sola unidad, y col6quela a un lado. Puede quitar el filtro levantando la rejilla de la tapa. Limpie el filtro con una solucibn de jabbn suave o reempl_celo, si es necesrio.
Step 4 Rotatethe CylinderHeadAssemblycounter clockwise1/8ofa turnandliftthe cylinderhead from the Motor Assembly. ROTATE COUNTER CLOCKWISE HACER GIRAR EN SENTIDO CONTRAHORARIO Paso 4 Haga girar el conjunto de cabeza de cilindro 1/8 de vuelta en sentido contrahorario y levante la cabeza de cilindm del conjunto de motor. Step 5 You have now separated the tool into the two major assemblies, allowing access to the areas that require periodic cleaning and lubrication.
Step 6 Spray the Cylinder Head with Degreaser Cleaner. Allow the dirt and debris to drip off. Paso 6 Aplique limpiador de seguridad a la tapa del cilindro. Permita que se escurran la suciedad y los dep6sitos. Step 7 Using a clean, lint-free rag, wipe offany remaining cleaner or dirt. Make sure the Seal Rings and Spark Plug are completely clean and clear of debris.
Step 8 Lightly lubricate the Seal Rings with 4-5 drops of Paslode Impulse ® Oil, part #401482. Make sure oil is applied evenly around the Seal Rings. Set the Cylinder Head Assembly aside. Note: Paslode Impulse Oil is specially formulated for use in the Paslode Cordless Tool. The use of other types of lubricants may cause rapid build-up of combustion residue or result in premature part failure. Paso 8 Lubrique ligeramente con 4 a 5 gotas de aceite lubricante Impulse ® de Paslode, N°401482.
Step 10 Spray a liberal amount of Degreaser Cleaner into the inside of the Sleeve and Combustion Chamber. Invert the Motor Assembly, and dirt drain out. and let excess cleaner Paso 10 Aplique una buena cantidad de limpiador de seguridad dentro della camisa y de la c_mara de combusti6n. Voltee hacia abajo el conjunto dal motor y permita que se escurran el exceso de limpiador y la suciedad. Step 11 Using a clean area of a lint-free rag, wipe off any remaining cleaner or dirt.
Step 12 With Motor Assembly tilted up, squeeze 3-4 drops of Im pulse Oil into Sleeve (Area "A") and 4-5 drops onto lower lip of Combustion Chamber (Area "B") and apply 4-5 drops around the top of the Combustion Chamber (area C). Rotate Motor Assembly while oiling to ensure oil is evenly distributed around Sleeve and Combustion Chamber. See Tool Cutaway Illustration on page 10. Note:Do notoveroilthetool.Excessiveoi/ingmaycausestaining of work surface.
Step14 Manuallypushthe DriverBladeupanddownto distributethe oilin theSleeveevenly. Reassemble the Paslode Cordless tool following disassembly Steps 1-4, pages 2-3 in Reverse order. Reassembly Note: Before tightening Cap Screws, depress the nose of the tool down on its work contacting element to close Combustion Chamber. Make sure cylinder head is centered to the motor, and that the Cap Assembly does not pinch exposed wires, Cap Screws must be tightened securely.
ombustion Tool (C_mara de combustion) Cutaway Sleeve Illustration Piston "Mid-Check"Area (Escape) Motor Assembly Conjunto del Motor _k DANGER Do not attempt to operate the tool unlessthe cap assembly is securely attached to the housing.
Very Dirty • • + _- Dirty " • • • • • Moderate • • • • • • Moderadas • Clean • • • • Limpias 0 CLEANING "f" • 2-3Days Weekly Muy sucias Sucias 2.5M 5M 7.5M 10M FastenersDdve_eek M= 1000 Fasteners INTERVAL •• Every 2 Weeks • Monthly • Every 2 Months The maintenance interval for cleaning the Paslode IM200 F-18 will vary depending upon the number of nails driven per week, and the operating conditions under which the tool is used.
IM200 F-18 Cleaning Procedure 888 Forest Edge Drive Vernon Hills, Illinois 60061 www.paslode.com Printed in U.S.A. ©2001, Illinois Tool Works, Inc.