P Model: IM250 II Part No. 900400 Cordless 16 Gauge Finish Nailer CORDLESS I IM250 F-16 II CORDLESS FINISH NAILER IMPORTANT! DO NOT DESTROY It is the customer's responsibility to have all operators and service personnel read and understand this manual.
Introduction Paslode Cordless Finish Nailer Operating Manual This manual is intended to acquaint you with the Paslode Cordless Finish nailer. Unlike other power fastening tools, the Cordless Finish nailer is powered by an internal combustion linear motor. In simpler terms, your Cordless Finish nailer is powered by a motor similar to the one that powers an automobile. The Cordless Finish nailer ignites a fuel and air mixture to produce the energy to drive the motor, which in turn drives the fastener.
An Overview of the Paslode Cordless Finish Nailer Description Specifications The Paslode Cordless Finish nailer is a self-contained, fully portable nailer that uses liquid hydrocarbon fuel to power a unique linear drive internal combustion motor. In order for you to fully understand the information contained in this manual, you need a basic understanding of the Paslode Cordless Finish nailer.
Safety Instructions The following safety instructions have been included in this booklet to provide you with basic information necessary for safe operation of the Paslode Cordless Finish nailer. DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND MANUAL INSTRUCTIONS. In addition to these instructions, training may be necessary. Contact your Paslode representative for additional information.
Safety Instructions WARNING Always wear EYE and EAR safety gear when working with or in the vicinity of the Impulse® Finish Nailer. 7. NEVER REMOVE OR DISABLE THE WORK CONTACTING ELEMENT. This device helps reduce the possibility of accidental fastener discharge by preventing the tool from operating until it is completely against the work surface. NEVER operate the tool if the work contacting element is not working properly. 8.
Safety Instructions 12. NEVER DRIVE FASTENERS INTO AREAS WITH CONCEALED HAZARDS. Always check the area behind the work surface for electrical wiring, gas pipes, water pipes, sewer drains or other potential hazards. 13. ALWAYS MAINTAIN SECURE AND UNOBSTRUCTED FOOTING WHEN ON LADDERS, PLATFORMS OR OTHER HIGH LOCATIONS. 15. PROPERLY STORE FUEL CELL. WARNING Always store fuel cells where they will not be exposed to an open flame, sparks or temperatures above 120° F (49° C).
Battery and Charging System Battery and Charging Sytem Charging Instructions The Cordless tool comes with a rechargeable battery and its own charging system. This battery and charging system combination is the only one that will work with the Paslode Cordless tool. The first step in preparing a new tool for operation is to fully charge the battery. New batteries are shipped discharged and must be charged prior to first use.
Battery and Charging System Battery Indicator Light The illustration is a close-up of the side of the Paslode Cordless Finish nailer handle. On the back side of the handle is a small plastic lens. This is the battery indicator light. When you insert a fully-charged battery into the tool, you will see a blinking green light. If the indicator light blinks red, recharge the battery. BATTERY INDICATOR LIGHT Inserting Battery 1. Load the battery, contacts first, into the Paslode Cordless Finish nailer. 2.
Fuel Cell and Metering Valve Fuel Cell DANGER EXPLOSION/FIRE HAZARD Read ALL safety instructions before using or handling the fuel cell. Failure to follow ALL instructions may result in explosion or fire. This may cause severe personal injuries or property damage. Keep the fuel cell away from heat, sparks and open flame. There is a second container inside the fuel cell. The inner container holds the fuel.
Fuel Cell and Metering Valve Attaching Metering Valve to Fuel Cell To attach the metering valve to a fuel cell: 1. Press downward on the front side of the valve (stem side) until it seats. 2. Press downward on the rear side of the valve until it seats. 3. The valve is now completely seated onto the fuel can and can be inserted into the tool. 1 2 3 NOTE: Impulse fuel cell are marked with an expiration date on the bottom of the can. For maximum performance use fuel before expiration date.
Fuel Cell and Metering Valve Inserting Fuel Cell Inserting the metering valve/fuel cell assembly into the Paslode Cordless Finish nailer is very simple. To begin, press up at the bottom of the actuator cover and pivot outward to open. The cover will swing out of the way. 2 ➔ As you slide the metering valve/fuel cell assembly into the Cordless Finish nailer, you will notice a yellow adapter at the top of the cylinder pocket.
Preparing the Paslode Cordless Finish Nailer for Use Paslode Cordless Tools and Outdoor Weather Fasteners The Cordless Finish nailer drives Paslode® F-16 Series fasteners which have been collated into strips. The use of fasteners that do not meet Paslode standards could cause tool damage and will void all warranty claims. Loading Fasteners The illustrations below show how to properly load fasteners into the Paslode Cordless Finish nailer. To load: P 1.
Impulse® Finish Nailer Operation PRESS WORK – CONTACTING ELEMENT AGAINST THE WORK SURFACE. P SQUEEZE TRIGGER Spark plug sparks and fuel/air mixture ignites. Combustion powers piston assembly driving fastener. ➔ Fan motor starts, fuel is injected into combustion chamber and mixed with air by the fan. Turn adjustment knob in either direction Depth of Drive Adjustment Remove the battery before adjusting the depth of drive. P LIFT TOOL RELEASE TRIGGER Combustion chamber opens.
Fasteners and Applications Applications The Paslode Cordless Finish nailer is suited for a variety of applications. Some of these are securing trim to door and window casings; attaching baseboards where walls meet floors; attaching moldings where walls meet ceilings; securing paneling; securing chair rails, picture molding and other decorative trim. Fasteners The Paslode Cordless Finish nailer drives Paslode F-16 Series nails.
Servicing Restrict Field Service to the Following CHECKING THE ENERGY LEVEL OF THE BATTERY RECHARGING THE BATTERY CHECKING THE FUEL CELL AND METERING VALVE REPLACING THE FUEL CELL CLEANING THE AIR FILTER CLEARING A JAM Fuel Cell Check If the Paslode Cordless Finish nailer's fan operates and the indicator light is green, but the tool will not cycle or does not drive fasteners completely, check the fuel cell.
Servicing Clearing a Jam (continued) When you get home: Make certain magazine mounting screws are tight and magazine is tight to nose. Attempting to fire tool with a loose magazine will result in loss of nail control, damage to tool, or nail discharge toward operator. 1. Place the battery in its charger if it needs charging as indicated by the red charge light on the handle. 2. Wipe your Impulse Finish nailer with a clean, soft cloth. 3. Remove and clean the filter every two days.
Troubleshooting Preparing Tool for Operation - Battery/Charger Problems SYMPTOM Battery does not appear to accept charge when charger is plugged into battery, or battery is plugged into the charger. Charger gets hot, makes excessively loud noise, or smokes during charging cycle. Charger cord or wall plug gets hot. POSSIBLE PROBLEMS SERVICE Inoperative indicator lights on charger, or defective charger. Try battery in tool after a full charge cycle.
Troubleshooting Power/Exhaust Stage of Operation SYMPTOM Tool operates properly, but fasteners do not drive fully. POSSIBLE PROBLEMS SERVICE Work-contacting element requires adjustment. Adjust work contacting element. Fuel cell is low. Check fuel cell and replace as required. There may be loss of seal in combustion chamber. Press work contacting element against workpiece for one minute. Pull trigger. If fastener does not drive, there is a leak that requires service.
DESCRIPTION PART NO. IM-250F 900400 PASLODE MODEL NUMBER DESIGNATION The model number of each Paslode tool contains information about the tool and the fasteners that are used with it. The following example illustrates the information contained in this tool model number. IM Paslode Cordless with IMPULSE Technology 250 F Finish Nailer (16ga) Maximum fastener length, in inches, that can be used with tool. (2.
