USER GUIDE Furniture Lock (model : FX200) Passtech Co., Ltd. Copyright ⓒ 2017 Passtech Inc. All rights reserved. You are strictly prohibited to copy, disclose, distribute, or use this document in part or as a whole for any purposes other than those for which this document is disclosed. This document is copyrighted and contains confidential information and other intellectual property rights of Passtech Inc.
FX200 User Guide Passtech Inc. reserves the right to make changes to its applications or services or to discontinue any application or service at any time without notice. Passtech provides customer assistance in various technical areas, but does not have full access to data concerning the use and applications of customer's products.
FX200 User Guide Table of Contents 1. Understanding FX200 FURNITURE LOCK .................................4 1.1 What is FX200 FURNITURE LOCK? ............................................. 4 1.2 Operating cards ............................................................................. 4 2. Types of Lock Operating Scenario ...........................................5 2.1 Free Selection (Shared Use) ......................................................... 5 2.2 Assigned Mode (Permanent Use) .......
FX200 User Guide 1. Understanding FX200 FURNITURE LOCK 1.1 What is FX200 FURNITURE LOCK? - FX200 locker locks are the locker lock operated by either 13,56 MHz RF Card Key. - FX200 can work as both offline (standalone) or online mode. - To set FX200 as online system, additional peripherals such as Access point, Server and client software are necessary. Refer Esmart Ultra client user manual for online lock system setup. 1.
FX200 User Guide 2. Types of Lock Operating Scenario FX200 locker locks are designed to work for the various operation requirements by simple set up process. Following operation modes can be programmed before or after lock installation. 2.1 Free Selection (Shared Use) - User card is not assigned to any certain lock but User is free to select any empty locker to occupy. - Programmable to make LED lamp blinked to represent locker is in use.
FX200 User Guide 3.1 RF tag uses ① FX200 can be set with two different credential acceptance modes. ② RF tag mode accepts RF tag ③ These modes can be set from Maintenance card (or setup card) [RF tag only] 3.2 Assigned Mode 3.2.1 Open & Close by RF card key ① RF card key can be used anytime. Touch the lock + Put User Card on the Lock. 3.2.2 Open & Close by smartphone (1) How it works - Visitor receives RFID user card at the front desk and goes to the locker assigned to this card.
FX200 User Guide - Thus, the smartphone is fully synchronized with RF user card. (2) Setting up the lock and user card issue Since BLE mobile access key is fully synchronized with RF user card, the first step is to set up the locker lock with set up card in Assigned mode and issue the user card and assign it to the locker. To do so, please refer to the Lock Management System User Guide Ver. 5.0. (3) Registration via Mobile App Run the mobile App.
FX200 User Guide locker. To open the locker, press the “lock icon” button on your mobile device monitor. (4) Multi-user and multi-locker There are four operation scenarios for BLE mobile access locking solution. An unlimited number of mobile devices can be assigned to one locker by syncing up with a card, but one mobile device can have only one card assigned, whereas one phone can operate up to 5 locker locks at the same time if its RF card have 5 locks assigned.
FX200 User Guide 3.3.2 Open & Close by Smartphone (4) How it works ① Download Passtech Mobile App from Google play store and install it into his smartphone ② After running the App, choose ‘Free mode’ on the setting tab. ③ Then, you can freely choose any available lock to operate. To access your mobile device, please set your lock for CSN Free mode and change the usage mode to Free mode from the Passtech APP from your mobile device. 3.
FX200 User Guide 4. Card Operation 4.1 Owner Card The role of the Owner card is to delete the Master card registration. Therefore, Owner card will be used to delete current master card registration in the lock, and make the lock to be ready to register new Master Card. It is simple to delete the Master card registration and to register new master card in the lock : ① Put the Owner card to the lock until lock sounds beep (one time) and red lamp lights.
FX200 User Guide ② Put the Maintenance card to the reader, and download the master card chip numbers to the Card. ③ Put the Maintenance card to the locks, then, new Master cards will be registered to the lock, and lost master card will be blocked. (2) Using Owner Card ① Delete the old master card registrations in the lock (refer to the 4.1) with Owner Card. ② Put new master cards to each lock so as to register new master cards. Then, old master card you lost will not be used.
FX200 User Guide please do not sway the card until the latch is moved. 4.3.2 Assigned Mode (Permanent Use) The initial status of the lock in Assigned Mode is closed status (latch out) ① Touch to wake up the lock. ② Put the User Card to the front body of the assigned lock. ③ Lock checks the card, if the key of the user card is correct, Lock will emit green LED lights and beep sound once. Then, lock will be opened, and closed again in 5 seconds. ④ To close the locker, just close the door.
FX200 User Guide can be updated with Maintenance card. 4.5 Audit Trail card ① Put Audit Trail Card to the lock. ② The latest event data (up to 150 events) will be downloaded from lock to the Card. Wait until melody is on. ③ Read the Card at LOS program, and 150 event data will be saved to the PC. 4.6 Lock Info card ① Put Lock info Card to the lock. ② Various lock information data will be downloaded from locks to the Card. One card can collect up to 40 locks.
FX200 User Guide 5. Indication Instruction 1) Open/Close:GREEN LED on for 0.2 second, one beep sound for 0.2 second. 2) Successful programming:Melody. 3) Indicate for mistake:RED LED flashes 3 times, 3 beep sounds 4) Low voltage:RED LED blinks 5 times, and beep sounds 5 times. 6. Specification Item Detail Material Polycarbonate Communication 2.
FX200 User Guide ANNEX A Beep & LED Table Beep LED Description 1 x short beep 1 x Green(2sec) OK 2 x short beep 1 x Red(2sec) Operation Error 3 x short beep 1 x Red & Green in Time over turn(2sec) Do-Re-Mi Melody 5 x short beep 1 x Red & Green in Successful Set up / mode turn(2sec) change / Time setting 5 x Red & Green Lack of power supply voltage Do-Re-Mi Melody 2 x Red & Green Successful connection between front and back bodies.
FX200 User Guide 1) Master card registration should be followed after deleting old Master card in the lock by Master card registration in the lock was failed. Owner card. 2) Put Master card on the lock before waiting time is out after Owner card. Cannot open the lock with Master Master card is not registered in the lock. card Please Register the Master card in the lock. 1. Check the Setting of User card by LOS.
FX200 User Guide 7 Regulatory Statement FCC Part 15.105 statement (Class A) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.