Data Sheet

ManualsBrandsPatlite ManualsAutomationPatlite Sounder EHV-M1TG 12 V DC, 24 V DC 110 dB

Max.

Conditions

Max.

Conditions

Max.

Conditions

No.EHV-W18F-1_18

FCC Part15 SubpartB Class

KC (KN22, KN24)

Remarks

UL Listed (File No.S24210)

Outer Dimensions Refer to 6. Outer Dimension Drawing

Conformity Standards

EMC Directive (EN 61000-6-4, EN 61000-6-2)

RoHS Directive (EN 50581)

UL 464, CSA-C22.2 No. 205-M1983

Less than 85 % (No condensation)

Indoors/Outdoors

Sideways

Volume at maximum and a 1 kHz at -6 dB sinusoidal wave played back from the horn opening.

Environmental Conditions

Operating Ambient Temperature

Operating Ambient Humidity

Mounting Direction

Inrush Current

-20 ℃

to +50 ℃

Mounting Location

Upright Upside-down

Rated Current Consumption

4.0 W (at DC12 V)

Operating Voltage Range DC10.8 V-DC35 V

SPECIFICATIONS

1. Specifications

1-1. General Specification

Model EHV-M1

Rated Voltage

Rated Power

Consumption

(for NPN/No-voltage)

9 A or less (at DC24 V)

DC12 V-DC24 V

480 mA

Rated Power

Consumption

(for PNP/Voltage Input)

t maximum volume and "Rapid Hi-Lo" alarm playback

Volume at maximum and a 1 kHz at -6 dB sinusoidal wave played back

t maximum volume and "Rapid Hi-Lo" alarm playback

5.8 W (at DC12 V)

5.0 W (at DC12 V)

Volume at maximum and a 1 kHz at -6 dB sinusoidal wave played back

8.0 W (at DC31.6 V)

12.5 A or less (at DC35 V)

4 A or less (at DC12 V)

Protection Rating IP65 (IEC 60529)

Storage Ambient Temperature -30 ℃

to +60 ℃

Storage Ambient Humidity Less than 85 % (No condensation)

Sound Pressure level (MP3)

45.0 m/s

IEC 60068-2-6:2007

(

ht Position

)

Environmental Conditions

Upright position from horn opening at a distance of 1 m.

Volume at maximum and "Stutter" alarm played.

Maximum: 105 dB

Vibration Resistance

Sound Pressure Level (Alarm) Maximum: 110 dB

Mass (Tolerance: ±10%) 1.25 kg

Environmental

Condition

Upright Installation

Withstand Voltage 500 VAC applied for 1 min between terminals and chassis without breaking insulation

Insulation Resistance More than 1 MΩ at 500 VDC between the terminals and the chassis

250 m/s

6 ms for 1,000 times

(

3 axis 1 direction

)

; 500 m/s

11 ms for 3 times

(

3 axis both directions

)

IEC 60068-2-27:2008 (Upright Position)

Impact Resistance

Summary of content (18 pages)

PAGE 1
SPECIFICATIONS 1. Specifications 1-1. General Specification Model Rated Voltage Operating Voltage Range Rated Current Consumption Max. Typ. Rated Power Conditions Consumption Max. (for NPN/No-voltage) Rated Power Consumption (for PNP/Voltage Input) Conditions Typ. Conditions Max. Conditions Inrush Current Operating Ambient Temperature Operating Ambient Humidity Storage Ambient Temperature Storage Ambient Humidity Mounting Location EHV-M1 DC12 V-DC24 V DC10.8 V-DC35 V 480 mA 4.
PAGE 2
Model Rated Voltage Operating Voltage Range Rated Current Consumption Max. Typ. Rated Power Conditions Consumption Max. (for NPN/No-voltage) Conditions Inrush Current Operating Ambient Temperature Operating Ambient Humidity Storage Ambient Temperature Storage Ambient Humidity Mounting Location EHV-M2 AC100 V-AC240 V (50/60 Hz) AC90 V-AC264 V (50/60 Hz) 150 mA 5.3 W (at AC240 V) Volume at maximum and a 1 kHz at -6 dB sinusoidal wave played back 7.
PAGE 3
1-2. Performance Specifications MP3 Mode Switch Condition Volume Control Sound Playback Number of Playback Channels Alarm/Melody Playback Mode Playback start-up time 1-3. MP3 Data Specification Playback File Bit Rate Maximum Playback Time Internal Memory Size Supported Memory Card SD Card Format Supported Application Software Remarks 1-4.
PAGE 4
2. Model E H V - M1 H F M Rated Voltage Wiring Specifications M1 DC12 V-DC 24V M2 AC100 V-AC 240V Melody Type H Cable T Terminal Buss F G Message Recording Type F Type G Blank None M Factory Installed Messages 3. Wiring Diagram - Non Voltage Contact Channel 8 Blue With NPN Transistor Channel 7 Green Channel 6 Orange Channel 5 Red Channel 4 Bright green Channel 3 Pink EHV-□H□□ Cable EHV-□T□□ Terminal Buss AC Power Supply Channel 2 Yellow L Channel 1 Lt.
PAGE 5
When connecting a Source-type PLC, be sure to insert a diode as indicated in the drawing below. Failure to insert a diode will lead to possible malfunction. Source Type PLC DIODES Channel 8 Blue OUT Channel 7 Green OUT Channel 6 Orange OUT Channel 5 Red OUT Channel 4 Bright green OUT Channel 3 Pink EHV-□H□ Cable EHV-□T□ Terminal Buss OUT Channel 2 Yellow OUT Channel 1 Lt. Blue COM Brown Power Supply White Power Supply Black ※Select a diode with ratings indicated below.
PAGE 6
4. Part Names and Functions A. Volume Inside Cover Volume adjustment is done by turning the volume. * Factory Setting: Center Position B. SD Card Slot (side) Use the SD card to transfer files with the MP3 data, then use the configuration file to select an alarm/melody, etc. C. Mode Switch (DIPSW) The setup for various functions is possible. * The figure is of an EHV-□H□□ (Cable Type).
PAGE 7
5. Functionality Details 5-1. Sound Group When "(5) MP3 setup" switch is being turned OFF, the sound group can be selected from up to 16 variations from groups A-P with the Mode Switch (DIPSW). A sound group cannot be selected when "(2) channel input method" is set for binary. Refer to "7. sound list" for the Mode Switch (DIPSW) and sound group combination which can be selected. * Factory Setting: Group A 5-2.
PAGE 8
5-3. Playback Mode The Mode Switch (DIPSW) can select from four different kinds of playback modes. When "(5) MP3 setup" is OFF, the hold playback function is active, regardless of the Mode Switch position. Normal Playback Input Priority Playback Memory Playback Hold Playback * Factory Setting : Normal Playback - Normal Playback If a signal input (Playback) is a pulse input, playback is ended as soon as the pulse input is off. The signal input (Playback) is maintained only when the input is held on.
PAGE 9
- Input Priority Playback When a signal input (Playback) is on during playback, the playback is stopped and the channel from the signal input (Playback) is reproduced. If the signal input (Playback) is a pulse input, even with the input held, playback plays only once. - Channel Input Method : Bit Input Channel1 Channel2 Channel3 Channel4 Message No. No.3 No.1 No.2 No.4 No.2 No.4 No.1 No.2 * All channels above 5 are the same * The wavy line indicates when playback was stopped and the message No.
PAGE 10
- Hold Playback It only plays back while the signal input (Playback) is maintained. Playback is stopped when the signal input (Playback) is removed. Repeated playback is done by maintaining a signal input (Playback). It does not play back if a signal input (Playback) is a pulse input. - Channel Input Method : Bit Input Channel1 Channel2 Channel3 Channel4 Message No. No.1 No.1 No.2 No.3 No.2 No.4 No.4 No.3 No.
PAGE 11
- Memory Playback When several signal inputs (Playback) are entered during playback, the memory of up to 5 signal inputs will play the corresponding message No. Signal inputs beyond the memory capacity is ignored. When playback is ended, the next available channel stored in memory will play. If the signal input (Playback) is a pulse input, even with the input held, the next message in memory is played back only once. - Channel Input Method : Bit Input Channel1 Channel2 Channel3 Channel4 Message No. No.
PAGE 12
- During a Stop input Channel1 Stop Message No. Memory Storage No.1 0 1 2 No.1 No.1 1 0 1 2 No.1 1 0 No.1 1 0 * The wavy line indicates when playback is stopped. - During a Clear input Channel1 Clear Message No. Memory Storage No.1 0 1 2 No.1 No.1 1 0 1 2 * The wavy line indicates when playback is stopped. No.EHV-W18F-12_18 No.
PAGE 13
5-4. Sound Mode The alarm/melody audibility reprodution can be selected with the Mode Switch (DIPSW). "Factory Mode" "Public Address Mode" - Factory Mode -- The audible sound is suitable as a warning alarm. - PA Mode -- The audible sound is suitable for public announcements. * Factory Setting: "Factory Mode" 5-5. MP3 Setup The MP3 can be selected for ON/OFF with the Mode Switch (DIPSW). MP3 setting OFF MP3 setting ON - MP3 setup ON ...
PAGE 14
5-6. MP3 Data Rewriting With the optional SD Card, MP3 data can be freely rewritten. Rewriting MP3 data requires the use of dedicated software (PATLITE Playlist Editor 2) and designating a regular file name. The built-in alarm/melodysounds are not overwritten. When the dedicated software (PATLITE Playlist When the dedicated software (PATLITE Playlist Editor 2) is not used Editor 2) is used Item Playback message No.
PAGE 15
5-7. Channel function (Function Which Uses Exclusive Soft "PATLITE Playlist Editor 2") Dedicated software (PATLITE Playlist Editor 2) can be used to assign functions to each signal input. In order for the channel function assignments to be used, the setup data has to be transmitted to the product via the SD Card. If the MP3 setup mode is OFF, this function becomes invalid. - Playback The corresponding channels are played back. - Sound Reduction The volume of sound being played back is decreased.
PAGE 16
5-9. Forced Playback When the Forced Playback mode is turned ON, it will play back after power is supplied, even with no signal input. It can be used for testing the playback volume or when controlled by power supply start-up. The Forced Playback is selected for ON/OFF with the Mode Switch (DIPSW). The sound (channel) to play back can be selected by the Mode Switch (DIPSW). MP3 setting ON : MP3 data and alarm/melody is selected with Mode Switch Numbers 1 - 6.
PAGE 17
6. Outer Dimension Drawing [mm] Vibration Absorption Rubber (EHV-M3 Only) Number 1 2 3 4 5 Part Names Case Cover Cable Angle Bracket Waterproof Gland * (3) is attached only to EHV-□H. No.EHV-W18F-17_18 Material PC PC UL2464 (AWG18x2C+AWG22x9C) φ9 SUS304 t=3.
PAGE 18
7.