Owner's manual

ManualsBrandsPATLITE ManualsLightingPHC-100A

Please be careful to wire the unit according to the following instructions. Mis-wiring will damage the internal circuitry and could cause a fire.

This product is for indoor use only. It should be used in a place where it is protected from rain and water. Moisture in the unit could cause a

breakdown of the unit or electric shock.

Warning

Do not use this product in a corrosive gas atmoshere.

Caution

8077-F

'09.4,AUTO

8077-F

T95100062

FT003

TO OPERATE THIS PRODUCT SAFELY, PLEASE OBSERVE THE FOLLOWING

㧵㧺㧿㨀㧾㨁㧯㨀㧵㧻㧺㧹㧭㧺㨁㧭㧸

[ TYPE : PHC-100A 㨉

Thank you for purchasing the PC-Output Relay Unit,PHC-100A. To ensure proper operation, prease read

this instruction manual thoroughly before attempting to use the system. Also, when undertaking maintenance,

inspection or repair work, be sure to refer to this manual. If you have any questions regarding this product,

please feel free to contact us.

PC-Output Relay Unit

1.Parts name

5.Specifications

Model PHC-100A

Rated voltage 24V DC

Operative voltage range 108V AC㨪132V AC (AC adaptor (bundled))

Power consumption Approx. 4W

Operative temp. range 0͠㨪40͠

Operative humidity range 85㧑RH

Dielectric strength

Insulation resistance

To be measured by an insulation measuring device of 500VDC between the power terminal and the case. More than 1Mǡ

1000VAC being applied between the power terminal and the case for 1 minute. Not braking insulation

Anti-noise 1500Vp-pޓPals range 1Ǵsecޔ100nsec

Vibration proof

19.6m/s

Mass Unit: Approx. 300 g Supplied AC adaptor: approx. 160g

Serial communication

Serial interface: RS-232C compliant

Transmission mode㧦Half-duplex mode , Transmission code㧦ASCII code

Synchronous mode㧦synchronous mode , Communication speed㧦9600bps

Data length㧦8 bit , Stop bit㧦1 bit

Parity, Flow Control: no setting required

Connector D-SUB9PޓMale connectorޓ

PATLITE Corporation disclaims all liability for any malfunction or damage occurring as a result of handling contrary to the instructions,

cautions and warnings mentioned in this manual.

Specifications are subject to change without notice.

Caution

Reset switch

Intemal contact

Output terminal

Momentary switch with green power monitor LED

On : All switch outputs are turned off

: All the communication command is invalid.

Off : Usual operation. CTS line of RS-232C is on and switch LED is on.

(

1800

)

60 41

Jack

O.D.㧦Ǿ5.5

I.D.㧦Ǿ2.1

ធὐኈ㊂

ޓޓޓޓޓޓޓ

߹ߢ

Contact capacity

125V AC,3A

30V DC,3A

87654321

࡝࡟࡯ធὐNo.(Relay contact No.)

㔚✢ⵍⷒ೸߈㐳ߐ㧦9mm(Strip)

න✢:

0.4㨪1.2mm(Single wire)

᠐✢:0.3㨪0.75mm

(Twist wire)

MODEL

PHC-100A

Reset switch

RS-232C

Power

24V DC

૶↪น⢻㔚✢

Applicable wire

115

117.5

100

Connect-disconnect lever

Wire insert point

AC adaptor connection

RS-232C port

(

D-SUB9 pin

)

Output terminal block

̪Lot number indicated

Reset switch with green power monitor LED

#4-40UNC Inch screw

Be sure to turn the power off before wiring. You may short-circuit the PCB or experience an electric shock.

Since this product uses screwless terminals, be sure to follow the instructions in this manual regarding wire type, wire diameter, and strip

length. Otherwise, there may be bad connections, excessive heating, or wires coming out of the terminals.

Make sure to insert the wire all the way to the bottom of the receptacle so that none of the stripped section is showing.

Otherwise there may be faulty operation, leakage or fire if the stripped section touches the product or if the wire comes out.

Warning

2.How to make wiring connection

The capacity of the internal contact is AC125V(DC30V), 3A. When inductive loads such as bulbs or motors are used, there is an

increase in current, which may shorten the life of the internal contact.

If the load current exceeds the capacity, or there is excessive inrush current, it may cause burning or welding of the contact.

This product is to be connected to one RS-232C serial port. Do not connect other devices simultaneously.

Otherwise, the result may be malfunction or damage to the serial port or devices.

4.Before requesting service

Substance

AC adaptor (bundled)

Caution

Please check the list shown below before requesting repairs. If the product still does not work, please contact us for repairs.

Please feel free to contact our sales office with any questions concerning the product.

For inquiry, you are required to identify the number indicated on the name plate of the product.

࡮

Power lamp stays

turned off

No reply (ACK, NACK)

࡮Confirm if supplied adaptor is securely inserted to a wall socket.

࡮Confirm if an adapter jack is securely inserted to the main body.

࡮Confirm if straight cable is used

࡮Confirm a communication condition and protocol

࡮Set ID to ??"[3FH, 3FH]

࡮Confirm an end code "!"[21H]

࡮Confirm if the reset switch is not being pressed

Problems What to do

Please note that any malfunction or damage resulting from modification is not guranteed under the warranty.

NOTES TO BE OBSERVED FOR SAFE OPERATION

عThe indications for warning are divided into the following classes according to the degree of danger or damage incurred when the warning is not taken

into consideration and the product is not corrently used.

Note to be followed to prevent any damage to the user and other personnel or to assets are as follows:

This symbol marks important instructions that, if ignored or incorrectly followed, could conceivably lead to death or serious injury.

This symbol marks important instructions that, if ignored or incorrectly followed, could conceivably lead to injury or property damage.

Caution

Warning

Terminal : Screwless terminal, Number of terminals: 16,

Applicable wire: Solid wire Ǿ0.4㨪Ǿ1.2mm (AWG26㨪AWG18)

ޓޓޓޓޓޓ 㧦 Stranded wire Ǿ0.3㨪Ǿ0.75mmޓ(AWG22㨪㧭㨃㧳20)

̪In case of using stranded wire, make sure to use an element wire which has more than Ǿ0.18mm diameter.

Contact:Non Voltage contact, Number of contacts:8, Contact Capacity: AC125V,3A/DC30V,3A

Life: Min. 200,000 operating (Rated Load, Operating 1,800times/h)

㧙㧝㧙

㧙㧠㧙

Summary of content (2 pages)

PAGE 1
4.Before requesting service 8077-F ࡮ Please check the list shown below before requesting repairs. If the product still does not work, please contact us for repairs. Please feel free to contact our sales office with any questions concerning the product. For inquiry, you are required to identify the number indicated on the name plate of the product. PC-Output Relay Unit 㧵㧺㧿㨀㧾㨁㧯㨀㧵㧻㧺㧹㧭㧺㨁㧭㧸 What to do Power lamp stays turned off ࡮Confirm if supplied adaptor is securely inserted to a wall socket.
PAGE 2
Caution ٨ Do not use excessive force when inserting a wire into the wire insert point. Damage may result to the terminal or product. ‫ع‬Wiring example 2 Lead wire operating : In the case of products operated by lead wire. (When the 120V AC product is used) ٨Wiring diagram Signal light Audible alarms etc. 1.Wiring to the terminal block ٨Terminal block RS-232C Straight cable 㧨AC adaptor connection㧪 120V AC‫ޓ‬ φ A solid wire‫ޓ‬Ǿ0.4㨪Ǿ1.2mm 㧔AWG26㨪18㧕 2 A twisted wire‫ޓ‬0.3㨪0.