Installation Instructions

ManualsBrandsPatriot Lighting Elegant Home ManualsIndoor LightingPatriot Lighting® Elegant Home Riccardo 4-Light Mini Pendant

ISSUED 03-2016

PACKAGE CONTENTS

1OF4

STYLE NUMBER: MND3312C

MENARDS NUMBER: 3511413

INSTRUCTION SHEET IS-MND3312C

● Before beginning installation of product, make sure all parts are present. Compare parts with package contents

list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the

product. Contact customer service for replacement part.

● Estimated Assembly Time: 30 - 45 minutes

● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,

Wire cutter, Safety glasses and (4) Candelabra Base 60W Maximum

● Helpful Tools (not included): Wire strippers.

PREPARATION

WARNING:

CAUTION:

● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching

off the circuit breaker or removing the fuse.

● These instructions are provided for your safety. It is very important that they are read completely before the

installation of your fixture. We strongly recommend that a professional electrician install the fixture.

● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient

time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.

WARNINGS AND CAUTIONS

1-800-645-3184

2pcs

1pc

Ceiling Canopy

Fixture Loop

1pc

Fixture Assembly

12” Rod

6” Rod

PART

DESCRIPTION

QUANTITY

A Crossbar Assembly

1pc

3pcs

2pcs

1pc

Green Ground Screw

()Pre-assembled to Crossbar

Wire Connector

Outlet Box Screw

Quick Link

6” x D5/8” Rod

1pc

2pcs

Summary of content (4 pages)

PAGE 1
-800-645-3184 INSTRUCTION SHEET IS-MND3312C STYLE NUMBER: MND3312C MENARDS NUMBER: 3511413 PACKAGE CONTENTS PART A B DESCRIPTION Crossbar Assembly Green Ground Screw ( Pre-assembled to Crossbar ) ISSUED 03-2016 QUANTITY F 1 pc G A 1 pc C Wire Connector 3 pcs D Outlet Box Screw 2 pcs E Quick Link 1 pc F Ceiling Canopy 1 pc G Fixture Loop 1 pc H 6” Rod 2 pcs I 12” Rod 2 pcs J 6” x D5/8” Rod 1 pc K Fixture Assembly 1 pc H I B C D J E K WARNINGS AND CAUTIONS WARNING: ●
PAGE 2
5” Dia. 2 3 1 54.5” OVERALL HEIGHT INCLUDES (2) 6” AND (2) 12” RODS 13” 18” Dia. (4) 60W Candelabra Base Bulbs (No Supplied) NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2" NO. PART NUMBER REPLACEMENT PART DESCRIPTION REQ. 1 9012EXLPIB ROD 12"L X .5"D 2 2 9006EXLPIB ROD 6”L X .
PAGE 3
INSTALLATION INSTRUCTIONS STYLE NUMBER: IS-MND3312C STEP 1: a. Secure the Crossbar Assembly to the outlet box (not included) with Outlet Box Screws. b. Tighten until snug. Outlet Box Crossbar Assembly Outlet Box Screw Note : The preassembled mounting nipple on the crossbar should protrude outward. STEP 2: a. Pass supply wires and ground wire through the 6” x D5/8” rod. b. Then thread the 6” x D5/8” rod to the fixture. c. Hand- tighten until snug. d. Choose desired hanging length for the light fixture.
PAGE 4
INSTALLATION INSTRUCTIONS STYLE NUMBER: IS-MND3312C STEP 5: a. Connect the fixture loop to the fixture chain preassembled to crossbar assembly using the quick link. b. Confirm that the mounting height is acceptable. Refer to STEP 1 if changes are required. I Note: To make the next step easier, cut the supply wire and ground wire 24 inches from the fixture loop. Important : Please pay attention to the polarity (wires labels L & N) when cutting wires. Wire identification will be needed in STEP 8.