Installation Instructions
32
Please read and understand this entire manual before attempting to assemble, operate or install the product.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
WARNING: These products may represent a possible shock or re hazard if improperly installed or at-
tached in any way. Products should be installed in accordance with these instructions, current electrical
codes, and/or the current National Electric Code (NEC). Disconnect power to the unit prior to installation.
WARNING: To reduce risk of re, electric shock, or injury to persons, be sure that power supply is
turned o at fuse box or circuit breaker before attempting installation or servicing of the xture.
WARNING:
Injury to persons and damage to the xture and/or mounting surface may result if the xture is pulled
from the surface. To reduce the likelihood of such injury or damage, mount to a surface that is mechanically sound.
SAVE THESE INSTRUCTIONS.
For safest operation, read and become familiar with complete installation
instructions prior to use. Pay close attention to this manual and stay within its guidelines when using this product.
ADDITIONAL SAFETY MEASURES
• To avoid electrical shock, do not turn on xture with missing or damaged lens.
• There are no serviceable parts inside LED module.
• LEDs emit bright light. Avoid looking directly at the light source.
• If power cord is used, do not alter it in any way.
• Do not install the strip lighting near ammable liquids.
• Do not use with any other cord, cable or connector other than those provided with the xture or
recommended in this instruction manual.
• Keep xtures away from curtains and other combustible materials.
• This portable luminaire has a polarized plug (one blade is wider than the other) to reduce the risk of electric
shock. This plug will t in a polarized outlet one way. If the plug does not t fully in the outlet, reverse the
plug. If it still does not t, contact a qualied electrician. Never use with an extension cord unless plug can
be fully inserted. Do not alter plug.
• Suitable for indoor dry locations only.
SAVE THESE INSTRUCTIONS
Before beginning assembly, installation, or operation of product, make sure all parts are present. Compare
parts with package and hardware contents lists on page 1. If any part is missing or damaged, do not attempt
to assemble, install or operate the product. Contact customer service for replacement parts.
Tools Required for Assembly (not included): Pencil, Phillips Screwdriver or Electric Drill, Safety Glasses
Estimated assembly time: 20 minutes
SAFETY INFORMATION
PREPARATION
INSTALLATION INSTRUCTIONS
5. To interconnect multiple xtures, plug the linking
cable (D) into the end of the rst xture and the
beginning of the next xture. Do not connect more
than 6 xtures together.
6. Use handheld remote control (C) for on/o control
and color control. Remove plastic tab from battery
door before use. To replace remote control’s
battery (F), follow directions on the back of remote
control (C) to slide battery drawer out. Replace
battery (F, + side up) and slide battery drawers
back in place.
1. Determine the desired location of the undercabinet
xture. Pull the covers o from both sides of the
undercabinet xture (A) and using a pencil, mark the
locations of the mounting holes onto the mounting
surface. Ensure the power input side (the side with
the infrared receiver) of the undercabinet xture (A) is
no more than 6 feet from a 120V power receptacle.
2. Use a drill gun (or start holes with an awl) and screw in
the mounting screws (E) through the mounting holes on
the undercabinet xture (A) at these locations.
3. Push the covers from either side of the
undercabinet xture (A) until they “click” in
place.
4. Insert the power cord (B) into power input side
of the undercabinet xture (A) (the side with the
infrared receiver). Then plug the other end of
power cord into a 120V AC receptacle.
A
A
A
A
A
A
Fig. 1
Fig. 2
Fig. 3
Fig. 5
Fig. 6
Fig. 4
B
D
E
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.