Installation Instructions

ManualsBrandsPatriot Lighting ManualsIndoor LightingLED Satin Nickel Plug-in Under Cabinet Light

1. This LED cabinet light fixture has a polarized plug (one blade is wider than the other) as a feature

to reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.

2. Never use with an extension cord unless plug can be fully inserted.

3. Do not alter the plug.

4. Do not attempt to install fixture while plugged in.

Important to Know

1. Read all instructions carefully before installation and operation.

2. If you are not familiar with state and local electrical codes, it is recommended that you consult with

a qualified electrician.

3. Maximum number of LED cabinet lighting fixtures per run should not exceed power supply wattage

rating. (Maximum 24W)

4. Do not use in wet locations, use indoors only.

5. Non-replaceable LEDs.

6. LED light output is strong enough to injure human eyes. Precautions must be taken to prevent

looking directly at the LEDs with unaided eyes.

Specification:

Important safety instructions.

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT

BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.

346-0925 / 346-0926

Installation Steps

NO.

1.25

Dimension(inch)

Model.:

346-0926

12 1.25

346-0925

5.1

0.4

Watts

7.6

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. Customer Service: 1-800-887-6326 (weekdays 9 a.m. – 5 p.m. CST)

3. READ AND SAVE THESE INSTRUCTIONS.

130920

Hardware Package:

(1 SET)

1. Find a suitable location to mount the fixture, the mounting surface should be a minimum of 1/2”

thick and approximately 3” distance for linking cord should be allowed at both ends of fixtures.

Summary of content (4 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS 346-0925 / 346-0926 WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Customer Service: 1-800-887-6326 (weekdays 9 a.m. – 5 p.m. CST) 3. READ AND SAVE THESE INSTRUCTIONS. Hardware Package: (1 SET) Important to Know 1. Read all instructions carefully before installation and operation. 2.
PAGE 2
. Carefully plan out your installation prior to actually securing your cabinet light fixture to the mounting surface make sure that your 11 ft. power adaptor will reach the nearest electrical outlet. Fig.1. 3. Place the mounting clips apart and mark with a pencil. Marks should be: 9 in. apart for models 346-0926 16 in. apart for models 346-0925 Mounting clips should be in line with each other. (See Figure 1) 4. Secure the mounting clips to the mounting surface with the dry wall screws provided.
PAGE 3
A. Using plastic connector: Fig.6. 24W Power Adaptor Plastic Connector Cabinet Lighting Fixture Outlet 1. Align connector on end of new fixture with connector on end of existing fixture. 2. Push new fixture to existing fixture until fixtures are flush and connectors snap together by using plastic connector. (See Figure. 6) B. Using linking cord: Fig.7. Cabinet Light Fixture Linking Cord Cabinet Light Fixture Install the additional cabinet light fixture following steps 1-5 of the instruction steps.
PAGE 4
Trouble Shooting Minor problems often can be fixed without the help of an electrician. Before doing any work on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock. PROBLEM POSSIBLE CAUSE Light will not come ON CORRECTIVE ACTION 1. Check if power supply is on. 2. Check power adaptor. 3. Test or replace switch. 1. Power is off. 2. Bad plug connection. 3.