30” GIBSON STREET CEILING FAN Owner’s Manual Models #20676 (355-0642) 20677 (355-0643) If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time.
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: PACKAGE CONTENTS 1 2 4 3 10 11 12 13 5 1. Canopy 10. Downrod 2. Canopy Cover 11. Downrod Pin 3. Mounting Bracket 12. Downrod Clip 4. Mounting Bracket Screw (x4) 13. Blade (x3) 5. Yoke Cover 15. Set Screw (x2) 6. Motor Assembly 7. Light Kit 19. Motor Screw (x6) 18 19 HARDWARE CONTENTS 16 Hardware Kit 18 7 17 18. Thumbscrew (x3) 9. Bulb (x2) 14 6 16. Hardware Kit 17. Owner’s Manual 8.
DIMENSION REFERENCE C B A A. 13.66 in. B. 10.46 in. C. 5.13 in. MOUNTING OPTIONS Two Mounting Options Downrod Mount Angled Ceiling Mount (Up to 16 degrees) Choose one of the following mounting options: Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer downrod (not included). Angled Ceiling Mount is best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary to ensure proper blade clearance from the ceiling.
SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS. CAUTION: All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.
ASSEMBLY INSTRUCTIONS 1. Turn OFF the electrical power at the main fuse or circuit breaker. 1 2. Loosen all four preassembled mounting bracket screws, then completely remove the two mounting bracket screws from the round holes of canopy. Set aside for later use. Mounting Bracket Screws 2 Canopy 3. Attach mounting bracket to outlet box (not included) using screws and washers provided with the outlet box.
ASSEMBLY INSTRUCTIONS 5. Insert the downrod through the canopy and yoke cover. Feed the wires and braided cable from the fan through the downrod. Canopy Yoke Cover Downrod 5 6. Slide the downrod into the yoke of the motor assembly, align the holes, then re-install the downrod pin and downrod clip. Secure with set screws and slide the yoke cover down until it rests on top of the motor assembly. Yoke Cover Downrod Downrod Pin Set Screw Downrod Clip 6 8 in. 7 7.
ASSEMBLY INSTRUCTIONS Slot Downrod Tab 9 Black (hot) White (neutral) 10 Green White Black Blue Bare/Green (ground) Warning: Do NOT use a full-range dimmer switch to control the fan speed. Mounting Bracket Screw Canopy 11 9. Install the downrod into the opening of the mounting bracket. Align the slot in the downrod with the tab on the mounting bracket. The downrod should not rotate in the mounting bracket if installed properly.
ASSEMBLY INSTRUCTIONS Blade Screw Blade Washer Blade Arm Blade 13 13. Insert the blade screws along with the blade washers through the blade and into the blade arm and secure with a screw cap. Repeat this step for the remaining blades and blade arms. Screw Cap Light Kit Motor Screw 14 Slot 14. Remove the six motor screws from the bottom of the motor assembly using a Phillips screwdriver (not included). Note: A magnetic Phillips screwdriver (not included) might make this step easier.
ASSEMBLY INSTRUCTIONS 17. Loosen the three thumbscrews near the bottom of the light kit. Lift the glass bowl into the light kit and re-tighten the previously loosened thumbscrews to secure. Light Kit Thumbscrew 17 Glass Bowl Reverse Switch Light Kit 18. Attach pull chain extensions to the pull chains. 18 Note: When facing the reverse switch on the light kit, the fan pull chain is on the right and the light pull chain is on the left. Pull Chain Extensions 19.
OPERATING INSTRUCTIONS 1 Light Pull Chain 1. The fan pull chain is located to the right of the reverse switch. It has four positions to control fan speed. One pull is HIGH, two is MEDIUM, three is LOW and four turns the fan OFF. The light pull chain is located to the left of the reverse switch. It turns the light ON and OFF. Fan Pull Chain 2. Use the reverse switch, located on the light kit to optimize your fan for seasonal performance.
TROUBLESHOOTING If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time. PROBLEM SUGGESTED REMEDY 1. Fan does not start 1.
LIMITED LIFETIME WARRANTY To obtain Service, please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time.
