Installation Instructions

Low Level
0% 50%
Fig.6
2. AUTO MODE (nighttime operation only)
● In "AUTO" mode, rotate Time Delay knob to the desired time setting
(30s/1min/3min). At dusk, the light turns on to pre-selected low-level
brightness and CCT color. When motion is detected, the light turns
to full brightness (5000K) and stays on as long as motion continues.
When the motion is no longer detected, the light at full brightness (5000K),
remains on for predetermined time you set (30s/1min/3min), and then
switch back to the set low level brightness and CCT color automatically.
● The light turns off automatically at dawn.
Note: You can adjust the low-level brightness (0~50%) and CCT color (2700K~5000K) by using the
low-level brightness (0~50%) knob and CCT color (2700K~5000K) knob on the backplate (See Fig.6)
3. PC MODE (nighttime operation only)
● In "PC" mode, the light turns on at full brightness at dusk and remains on until dawn.
Note: You can adjust the CCT color (2700K~5000K) by using the CCT color (2700K ~5000K) knob on the
backplate. (See Fig.6)
4. 3 HOURS (3H) MODE (nighttime operation only)
● In “3H” mode, the light turns to high-level brightness (100%) at dusk, and stays "ON" for 3 hours, then it turns to
low-level brightness. It turns to high-level brightness (100%) when motion is detected, and stays on as long as
motion continues. When motion is no longer detected, it remains on for the predetermined shut-off delay time you
set (30s/1min/3min), then returns to the predetermined low level brightness and CCT color automatically.
● The light turns off automatically at dawn.
Note: You can adjust the low-level brightness (0~50%) and CCT color (2700K~5000K) by using the
low-level brightness (0~50%) knob and CCT color (2700K~5000K) knob on the backplate (See Fig.6)
5. CUSTOM SETTING MODE (nighttime operation only):
● In "CUSTOM SETTING" mode, the light turn on at dusk and off at dawn automatically.
● Instead of "3H", the motion sensor operation can be set to start at a specific time. Turn the wall switch “OFF”, and
turn it “ON” twice within 3 seconds. The light will go into motion-sensor operation at the specified time every night.
The light turns off automatically at dawn.
For example, a homeowner wants to have the light stay on high-level brightness from dusk to 8pm, and would like
the light to go into "AUTO motion sensor mode. To achieve this, the homeowner will turn the wall switch “OFF”,
and turn it “ON” twice within 3 seconds. This sets the time the light goes into "AUTO" mode every day, the light
will behave the same way.
To revert back to Default, turn the wall switch “OFF” and then turn it “ON” after 5 seconds.
Note: You can adjust the low-level brightness (0~50%)
and CCT color (2700K~5000K) by using the low-level
brightness (0~50%) knob and CCT color (2700K~5000K)
knob on the backplate (See Fig.6)
6. Manual Override (nighttime operation only)
● To temporarily override the settings in “AUTO” or “3H” mode
for on-demand continuous high-level brightness at night, turn
the wall switch “OFF” then turn it “ON” twice within 3 seconds,
the light remains on all night long. To shift back to “AUTO” or
“3H” mode, turn the wall switch “OFF” then turn it “ON” twice
within 3 seconds again. (See Fig.7)
● The light turns off automatically at dawn.
7. CCT Color Switching
● CCT Color adjustable function apply to low level brightness, 3H, PC and Custom Setting mode.
Fig. 7
“AUTO” or
“3H” Mode
Manual
Override
Manual Override Operation Diagram
Turn wall switch OFF-ON-OFF-ON
in 0.5~3 Seconds
Turn wall switch OFF-ON-OFF-ON
in 0.5~3 Seconds
Note: To make sure the above functions operate properly, always keep the wall switch in the “ON” position
(including the daytime).
ASSEMBLY INSTRUCTIONS (continued)
ASSEMBLY INSTRUCTIONS (continued)
FUNCTION AND OPERATION (continued)
Page 5 of 8
201029