Installation Instructions

Security Light
Dusk-to-Dawn
MODEL No: V-5500D-G
PACKAGE CONTENTS
INSTALLATION INSTRUCTIONS
ADDITIONAL WARNINGS
3 YEAR LIMITED WARRANTY
This product is guaranteed against failure due to factory defects on materials or workmanship for three (3) years from the date of
purchase. This warranty is non-transferable and applies only to the original owner. Proof of purchase is required for repair or
replacement. This warranty does not cover normal wear of parts or damage resulting from any misuse of the product. Misuse of the
product includes, but is not limited to: washing the product, using in extreme weather conditions, opening the product, or trying to
remodel the product. Important: this warranty is only valid if the product has been purchased through an authorized reseller.
WARNINGS
WARNING: This product may represent a possible shock or
fire hazard if improperly installed or mounted. Products should
be installed following these instructions, local electrical codes and/or
the current National Electric Code (NEC).
WARNING: This produc t needs to be grounded properly in a
manner consis tent with l oc al el ec tr i c al codes and/or the
current National Electric Code (NEC). If the installer cannot
determine if this product i s pr oper l y gr ounded, has no gr ound wire,
or is unfamil i ar wi th el ec tr i c al wir i ng methods of pr oper l y
grounding fixture, c ons ul t a qual i fi ed el ec tr i c ian.
WARNING: Do NOT look directly at LED light sources.
This fixture is IP54 rated and therefore suitable for dry or
damp locations only for indoor and outdoor.
WARNING: Use only in 120VAC, 60Hz circuits.
WARNING: Do NOT mount on ground.
WARNING: TO AVOID ELECTRIC SHOCK,
DISCONNECT POWER BEFORE INSTALLING
SAFETY AND PRECAUTIONS
1. Suitable for wet locations.
2. Do NOT touch LEDs.
3. Do NOT look directly at LED light sources.
4. The LED modules used in this fixture are not serviceable.
5. Do NOT make contact or install fixture while making contact with water.
6. NOT suitable for ground installations. Do NOT mount below 6 ft.
7. This product is inspected prior to shipping. Do not use if product is cracked, broken or missing parts.
8. Suitable for use in operating environments ranging between -13° F to 122° F (-25° C to 50° C).
9. Do NOT leave bare wires exposed outside of the electrical connections.
10. Electrical requirements can be found on back of the fixture.
11. If unsure how to install a light fixture, call a qualified electrician.
12. Do NOT install near other sources of light. Nearby light sources may prevent sensor from detecting darkness.
• Shut off power at the circuit breaker or fuse box before installing or servicing this fixture.
CUSTOMER SERVICE
For questions regarding this product, please contact us at 303.652.6164
, M-F 7am - 4pm MT .
Before beginning, disconnect the power to the junction box. If replacing an existing fixture with more than two wire
leads, make a note as to the color of the wire and where they were connected.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment. The user is cautioned that any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from
that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.
Mount fixture at least 6 ft off the ground.
Electrical requirements can be found on fixture.
Use with a Minimum 90° supply conductors.
Revision Date: 08-07-2017
TROUBLESHOOTING GUIDE
CLEANING INSTRUCTIONS
Disconnect power to fixture before cleaning. Using a soft cloth, clean the fixture using a mild, non-abrasive glass cleaner. DO NOT
use solvents. DO NOT use cleaners containing abrasive agents. NEVER spray liquid cleaner directly onto the LEDs, fixture or wiring.
Before starting work to connect the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
Fixture does not turn on.
Problem
Probable Cause
Solution
Light comes on during the
daylight hours.
Light cycles ON and OFF
continuously (strobe light effect).
1. Dusk-to-dawn sensor is
detecting reflected light
from the security light.
1. Change the position of the light head.
Reposition light away from the reflecting surface.
2. Place a small piece of black electrical tape over
the bottom half of the dusk-to-dawn sensor.
3. Move the light to a different location where the
results are better.
1. Bad connection.
2. Faulty switch.
3. Power is off.
1. Fixture is located in a shaded
area; dusk-to-dawn sensor is
detecting darkness.
1. Check wiring connections.
2. Test switch or replace it.
3. Verify power supply is on.
1. Shine a light at the dusk-to-dawn sensor. If the security
light immediately shuts off, then the fixture is located
in an area that is too dark to allow enough light to
enter the sensor. The light will need to be relocated.
Circuit breaker trips or fuse blows
when light is turned on.
Discontinue use
immediately.
1. Call customer service at 303.652.6164.
2. Call an electrician.
WARNING: DO NOT alter or disassemble the fixture, it
is completely enclosed and does not contain
replaceable or serviceable parts.
DIMMING
• THIS FIXTURE DOES NOT WORK WITH DIMMERS.
LED Facts:
Color Temperature: 5000K
Lumens: 5500 LM
Lumen Efficacy: 90
Input Voltage: 110-240V, 50-60Hz
Rated Watts: 58W
CRI > 70
Power Efficiency: 88%
LED Emitter Life: 50,000 hours
Cold Start Operating Temperature:
-13° F to 122° F(-25° C to 50° C)
Warm Up Time: +/-120s (±25%)
Beam Angle: 120°
2. Feed the supply wires through the
elongated hole in the mounting plate. Guide
the mounting post through the center hole of
the mounting plate (Fig. 3). Push the
mounting plate onto the mounting post until
flush with the surface (Fig. 4). The “UP” and
“arrow” need to be located at the top.
4. The light canopy fits onto the mounting plate in a specific manner (Fig. 8). Line
the holes and posts up and guide the light canopy onto the mounting plate
already attached to the junction box. There are also 3 contact pins that align and
will engage the terminal block on the mounting plate (Fig. 9).
3. Insert the Ground Wire into the
terminal marked “ ”, insert the Black
Supply Wire (Live) into the terminal
marked “ ”. Insert the White Supply
Wire (Neutral) into the terminal marked
“ ”(Fig. 6) and tighten screws to each
terminal (Fig. 7).
1. Pull the ends of the supply wires out the front
of the junction box. Fasten the crossbar to the
junction box as shown (Fig. 1 & 2). Works with
round, rectangular and square boxes, mounted
in any direction.
4.625 in.
11,74cm
9 in.
22,9cm
7.125 in.
18,1cm
(Fig. 1)
(Fig. 2)
1. Call customer service at 303.652.6164.
2. Call an electrician.
2. Dusk-to-dawn sensor may
be malfunctioning.
Crossbar with
Ground Screw
Round
Plastic Cap
Light Canopy
Mounting Plate
Contact Terminals
Light Head
2x
Wood Screws
2x (short)
Machine Screws
1x (long)
Machine Screw
Adjustable Fixture Elbow
Mounting Post
Dusk-to-Dawn
Sensor
Surface Box Gasket
OPERATION
OPTIONAL
1. The light head can pivot a full 90°up
and down 90°. It can also rotate right or
left for a total of 180° to aim light in a
multitude of angles. There are two
stops located on the fixture neck that
prevent the light head from rotating
beyond 180°. Do NOT try to defeat this
feature. Rotating beyond the set range
could damage the wires and lead to an
unsafe situation.
5. Insert the machine screw through the center
hole in the mounting base and secure the fixture to the
junction box (Fig. 10). Restore the power to the junction
box. Make sure the wall switch that controls the electrical
box for your security light is returned to the “ON”position
and check that the light is functioning properly. If the light
functions properly, fit the round plastic cap into the the
center hole in the light canopy to prevent water from
seeping into the fixture housing (Fig. 11).
6. Use silicone seal/caulking (not included) to seal-off around the mounting plate and the mounting surface to add an additional barrier
to prevent water seepage into the electrical enclosure.
(Fig. 10)
(Fig. 11)
Crossbar with
Ground Screw
For outdoor use.
(Fig. 3)
(Fig. 4)
DISCONNECT
POWER BEFORE
SERVICING
COUPER
L’ALIMENTATION
AVANT
L’ENTRETIEN
(Fig. 8)
contact
pins
(Fig. 9)
Mounting Post
Mounting Plate
1
3
4
2
180°
180°
UP
DOWN
(Fig. 5)
(Fig. 7)
(Fig. 6)
LEFT RIGHT
Stops