Installation Instructions

ManualsBrandsPatriot Lighting ManualsIndoor LightingEmma 5-Light Bronze Flexible Track Lighting Set

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

NOTE: 1. Before installing, consult local electrical codes for wiring requirements.

2. Please read these instructions carefully before installing this fixture. If you are not

familiar with installations, please consult a qualified electrician.

3. Do not install this lighting system in a damp or wet location.

4. Lighted lamp is hot! Do not touch lamp at any time. Use a soft cloth or cupule. Oil

from skin may damage lamp.

5. Customer Service: 1-800-887-6326 (weekdays 9 a.m. – 5 p.m. CST)

349-5900

WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT

BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Canopy Installation

Fig.1

1. Attach the cross bar to the outlet box by using two mounting

screws.

2. Pull out the outlet wires and the house grounding wire from the

outlet box. Make wire connections using the wire nuts:

a. Connect the black wire from the fixture to the black wire from

outlet box.

b. Connect the white wire from the fixture to the white wire from

outlet box.

c. Attach the fixture grounding wire to the cross bar with the

green grounding screw. Then connect it to the house grounding

wire with a wire nut.

Carefully put the wires back into the outlet box.

3. Attach the canopy to the cross bar. Lift the canopy, allowing the

two screws to slide into the mating slots. Rotate the canopy

clockwise until both screws from the cross bar drop into the slot

recesses. Tighten screws securely.

Wire Nut

Mating Slot

Canopy

Rail Adapter

Outlet Box

Screw

Mounting Screw

Green Grounding

Screw

Cross Bar

Patriot Lighting

130917

Hardware Package:

(1 SET)

Summary of content (4 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS 349-5900 WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult local electrical codes for wiring requirements. 2. Please read these instructions carefully before installing this fixture. If you are not familiar with installations, please consult a qualified electrician. 3. Do not install this lighting system in a damp or wet location. 4.
PAGE 2
Rail support Installation: Anchor Rail Support 14~18 inches Ceiling Support Base Rail Support Dry Wall Screw 14~18 inches Fig.2-b Pipe of rail support Fig.2-a 1. Mark two desired positions and drill them on the ceiling for two rail supports on the side of the canopy. NOTE: Center the canopy between two rail supports and The distance between each rail support and the canopy is 14 ~ 18 inches (See Fig 2-a). So the remainder length of the rail could be bent to a wonderful arc. 2.
PAGE 3
Rail Adapter Grounding Clip Fig.8-a Fig.8-b 10. Repeat the steps of Rail Supports Installations to locate the rest rail supports. Then Follow steps 2~4 of Rail Installation to install the rail onto the other rail supports. Grounding Strip Brass Strip Brass Clip Rail Fig.7 Spot Light Installation: CAUTION: To reduce the risk of fire, electrical shock, or personal injury, do not touch or remove the spot light on the rail when the light is on. Instead, turn off the electrical power.
PAGE 4
. Attach the glass shades to the glass holders, secure them with socket rings, using supplied fixer. (See Fig.12) 5. Install bulbs (Included). (See Fig.12) a. Attach the cupule to the top surface of the halogen bulb lens. b. Insert and twist the bulb (GU10 BASE MR16C BULB ONLY) into the socket of the lamp holder using the cupule. c. Remove the cupule from the halogen bulb lens by pulling the knob of the cupule. Note: Do not discard the cupule, it will be needed when replacing the bulb.