- Patton Electronics Short Range Modem with Carrier Sense USER MANUAL 1006

ManualsBrandsPatton electronic ManualsNetwork Card1006

MODEL 1006

DB-9 Async. Short

Range Modem with

Carrier Sense

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

http://www.patton.com

Part #07M1006-C

Doc. #060011UC

Revised 4/29/98

USER

MANUAL

An ISO-9001

Certified Company

Summary of content (8 pages)

PAGE 1
USER MANUAL MODEL 1006 DB-9 Async. Short Range Modem with Carrier Sense Part #07M1006-C Doc. #060011UC Revised 4/29/98 An ISO-9001 Certified Company SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www.patton.
PAGE 2
1.0 WARRANTY INFORMATION Patton Electronics warrants all Model 1006 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not perform as warranted, your sole recourse shall be repair or replacement as described above.
PAGE 3
2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Year parts and labor. If any questions or problems arise during installation or use of this product, please do not hesitate to contact Patton Electronics Technical Support at (301) 975-1007. 3.0 INSTALLATION The Model 1006 is easy to install.
PAGE 4
1. RJ-11 SIGNAL RJ-45 1 ----------------GND† 2 ----------------RCV3 ----------------XMT+ 4 ----------------XMT5 ----------------RCV+ 6 ----------------GND† SIGNAL 1 ----------------N/C 2 ----------------GND† 3 ----------------RCV4 ----------------XMT+ 5 ----------------XMT6 ----------------RCV+ 7 ----------------GND† 8 ----------------N/C Open the unit by gently inserting a screwdriver between the DB-9 connector and the lip of the plastic case (see below).
PAGE 5
4. Connect one pair of wires to XMT+ and XMT- (transmit positive and negative) on the terminal block, making careful note of which color is positive, and which color is negative. 8. Place the 2 halves of the strain relief assembly on either side of the telephone wire and press together very lightly. Slide the assembly so that it is about 2 inches from the terminal posts and press together firmly. If your cable diameter is too small or too large for our strain relief, please contact our technical support.
PAGE 6
APPENDIX A 10. TIP the top half of the case as necessary to place it over the strain relief assembly. Do not snap the case together yet. PATTON MODEL 1006 SPECIFICATIONS Transmission Format: Asynchronous Data Rate: 0 to 19,200 bps (no strapping) Distance: See table below Surge Protection: Compliant with IEC 801.5 level 2, 1kV (Model 1006S Only) 11. Insert one captive screw through a saddle washer and then insert the entire piece through the hole in the DB-9 end of the case.
PAGE 7
APPENDIX B APPENDIX C PATTON MODEL 1006 CABLE RECOMMENDATIONS PATTON MODEL 1006 PIN/SIGNAL ASSIGNMENTS The Patton Model 1005 operates at frequencies of 20kHz or less and has been performance tested by Patton technicians using twistedpair cable with the following characteristics: Wire Gauge Capacitance Resistance 19 AWG/.9mm 22 AWG/.6mm 24 AWG/.5mm 83nf/mi or 15.72 pf/ft. 83nf/mi or 15.72 pf/ft. 83nf/mi or 15.72 pf/ft. .0163 Ohms/ft. .0326 Ohms/ft. .05165 Ohms/ft.