USER M A N UA L MODEL 5 7 4 , 5 7 6 , 5 7 8 , 584, 586, 588 Standalone Hub 100Base-T (CAT-5) Surge Protectors Part# 07M57x/58x-A Doc# 074100UA Revised 10/18/96 An ISO-9001 Certified Company SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www.patton.
1.0 WARRANTY INFORMATION Patton Electronics warrants all Model 57x/58x components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not perform as warranted, your sole recourse shall be repair or replacement as described above.
.0 INSTA L L AT I O N Model’s 57x and 58x surge protectors are easy to install and are designed to operate transparently to your network. This section describes cohnnection procedures for both models. 3.1 PRODUCT APPLICATIONS Also, the flat braided grounding wire(s) on the Model 57x should be attached to the grounded metal frame of the device being protected. If it is not possible to attach it to the equipment being protected, contact Patton Technical Support (See Section 1.1). 3.1.
3.2 INSTALLATION PROCEDURES In order to operate as designed, the Model 57x and 58x must be connected correctly to your Cat-5 network. For the safest installation, please read all the instructions below and follow them very carefully. 3.2.1 Connecting the Model 57x or 58x to an I/O Port 1. Turn off equipment power and disconnect the existing connection between the UTP cable and the equipment’s I/O port. 2.
APPENDIX A SPECIFICATIONS Environment: Category-5 Interfaces that utilize the RJ-45 connector, including RS-422, 423, 10BaseT, Token Ring, Fast Ethernet, 100Base-T, 100Base-T4 and ATM Connectors: RJ-45 Female Response Time: Clamped to 13V after 0.1µS Characteristic Impedance: 100 Ohms NEXT Loss (worst pair): Better than -40 dB at 100 MHz Surge Clamping Voltages: Model 57x: 13 V max with 1 KV Input; Model 58x: 15 V max with 2 KV Input Surge Rating: IEC 801.
APPENDIX C EIA/TIA TSB-40A COMPLIANCE APPENDIX C (continu e d ) TSB-40A COMPLIANCE TESTING RESULTS TYPICAL ATTENUATION MEASUREMENT The Model 57x/58x series surge protectors have been designed to conform to stringent EIA/TIA TSB-40 standards as required for all Category-5 connecting hardware. These standards specify the capacitance and near end cross-talk (N.E.X.T) to insure proper operation of ALL connected equipment. Specific test results are shown in the tables on the following pages*.
APPENDIX C (continu e d ) TSB-40A COMPLIANCE TESTING RESULTS TYPICAL RETURN LOSS MEASUREMENT Appendix C (continued) TSB-40A Compliance Testing Results TYPICAL INSERTION LOSS MEASUREMENT Freq MHz Pins: 1-2 dB Pins: 3-6 dB Pins: 4-5 dB Pins:7-8 dB Spec dB 1 4 8 10 16 20 25 31.25 62.5 100 34.0 38.0 39.0 38.0 34.0 33.7 31.0 28.1 21.0 17.0 28.0 38.0 41.0 41.0 35.0 33.0 30.0 27.0 22.0 21.0 28.0 45.0 42.0 39.0 33.0 31.0 34.0 28.0 22.0 18.2 29.0 43.8 42.0 39.5 33.0 31.6 30.0 27.8 22.0 17.
Dear Valued Customer, Thank you for purchasing Patton Electronics products! We do appreciate your business. I trust that you find this user manual helpful. We manufacture one of the widest selections of data communications products in the world including CSU/DSU's, network termination units, powered and self-powered short range modems, fiber optic modems, interface converters, baluns, electronic data switches, data-line surge protectors, multiplexers, transceivers, hubs, print servers and much more.