USER MANUAL MODEL 2174 CopperLINK™ High Speed Ethernet Extender This is a Class A device and is not intended for use in a residential environment. Part# 07M2174-UM Rev.
CONTENTS 1.0 1.1 1.2 1.3 1.4 1.5 1.6 Warranty Information ................................................................. Regulatory Information ................................................................. EMC Directive:.............................................................................. Low-Voltage Direcive (Safety): ..................................................... PSTN: ...........................................................................................
RJ-45 .......................................................................................... 19 C.2 CopperLINK Interface ................................................................ 19 RJ-45 .......................................................................................... 19 Terminal Block............................................................................ 19 D Line Rate & Reach Chart, Based on 24 AWG (0.5 MM) .........
1.0 WARRANTY INFORMATION Patton Electronics warrants all Model 2174 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of the shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not performs as warranted, your sole recourse shall be repair or replacement as described above.
tion. The device has been tested and found to comply with the limits for a Class A computing device in accordance with specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection from such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular installation.
1.6 SAFETY WHEN WORKING WITH ELECTRICITY • This device contains no user serviceable parts. This device can only be repaired by qualified service personnel. • Do not open the device when the power cord is connected. For systems without a power switch and without an external power adapter, line voltages are present within the device when the power cord is connected. • For devices with an external power adapter, the power adapter shall be a listed Limited Power Source.
In accordance with the requirements of council directive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate this product from other waste and scrap and deliver to the WEEE collection system in your country for recycling. WARNING WARNING This device contains no user serviceable parts. This device can only be repaired by qualified service personnel. This device is NOT intended nor approved for connection to the PSTN.
2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for one year for parts and labor. If any questions or problems arise during installation or use of this product, contact Patton Electronics Technical Support at +1 (301) 975-1007. 2.
Figure 1. Typical application The pair of 2174 models work together to create a transparent extension between two peered Ethernet LANs using twisted pair (2-wire), Cat5+, or 75-ohm BNC. Figure 1 shows a typical point-to-point application. 3.0 INSTALLATION CAUTION The Interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability.
Et Et Et Et C VD 12 h3 h2 h1 h0 1A Et Et Et Et C VD 12 h1 h0 1A Et Et Et Et C VD 12 h3 h2 h2 h1 h0 1A Figure 2.
3.1 CONNECTING THE LINE INTERFACE CAUTION The Interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability. The Model 2174 supports communication between two peer Ethernet LAN sites over a distance of up to 10,000 ft (3 km) over 24 AWG (0.5 mm) twisted-pair wire, Cat5+, or 75-ohm BNC.
h3 Et h2 Et h1 Et h0 Et 12 VD C 1A RING TIP Figure 4. Model 2174 (Terminal Block) twisted pair line interface Connecting the Line Interface for Model 2174/BNC To connect the line interface of the Model 2174/BNC, simply use a coaxial cable with a BNC connector at each end to connect the pair of Model 2174s. 3.
3.3 CONNECTING POWER CAUTION The Interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability. The Model 2174 does not have a power switch, so it powers up as soon as it is plugged in. An external AC or DC power supply is available separately. This connection is made via the barrel jack on the rear panel of the Model 2174.
S1 S1 Switch toggle Push toggle down for OFF position 1 2 3 4 5 7 8 ON S1 Push toggle up for ON position ON 6 1 2 3 4 5 6 7 8 Figure 6. DIP switch orientation 4.2 CONFIGURING DIP SWITCH S1 DIP switch S1 is where you configure the CopperLINK line. The following tables describe the configuration for the 2174.
Switch S1-1: Local/Remote Configuration Use switch S1-1 to configure the unit as Remote or Local in the Model 2174 pair. Table 2: Local/Remote Unit Configuration S1-1 ON OFF Setting CPE/Remote CO/Local Switches S1-2 and S1-3: Symmetric/Asymmetric Operation Use switches S1-2 and S1-3 to configure the CopperLink line rate typeand operation.
5.0 OPERATION Once the Model 2174s are properly installed, they should operate transparently. No user settings required. This section describes reading the LED status monitors. Before applying power to the Model 2174, please review section 3.3, “Connecting Power” on page 13 to verify that the unit is connected to the appropriate power source. 5.
APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • Four RJ-45, 10/100Base-T, IEEE 802.3 Ethernet • CopperLINK Connection: RJ-45 A.2 TRANSMISSION LINE Two-wire unconditioned twisted pair or 75-ohm BNC A.3 COPPERLINK LINE RATE AND COPPERLINK DISTANCE • Line Rate: Up to 200 Mbps asymmetrical • Distance: Up to 9,842 ft (3 km) Note Distances depend on line rate and line conditions. A.
APPENDIX B MODEL 2174 SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Model # Description Base Models 2174/EUI-2PK High Speed CopperLink Ethernet Extender Kit (Local and Remote); RJ45 Line, 100-240VAC 2174/TB/EUI-2PK High Speed CopperLink Ethernet Extender Kit (Local and Remote); Terminal Block Line, 100-240VAC 2174/BNC/EUI-2PK High Speed CopperLink Ethernet Extender Kit (Local and Remote); BNC Line, 100-240VAC 07M2174-UM User Manual Power Supplies PS-03671H1-002 100-240VAC (12V, DC/2A) W
APPENDIX C MODEL 2174 SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX• Pin 3: RX+ • Pin 6: RX• Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection Terminal Block Et E Et Et 12 C VD h3 th2 h1 h0 1A RING TIP Figure 1.
APPENDIX D LINE RATE & REACH CHART, BASED ON 24 AWG (0.5 MM) Table 6: Line Rate & Reach Chart Using Twisted-Pair (Long Range) Mode (Long Range) Symmetric Asymmetric Distance in Feet Mbps ft m/km DS US 250 ft 1000 ft 2,000 ft 3,000 ft 5,000 ft 10,000 ft 76 m 305 m 610 m 914 m 1.5 km 3 km 68 62 50 33 16 2.5 40 44 16 4 2 1 250 ft 1000 ft 2,000 ft 3,000 ft 5,000 ft 10,000 ft 76 m 305 m 610 m 914 m 1.
Table 7: Line Rate & Reach Chart Using Twisted-Pair (High Speed) Mode (High Speed) Distance in Feet Mbps ft m/km DS US Symmetric 250 ft 1000 ft 2,000 ft 3,000 ft 3,500 ft 76 m 305 m 610 m 914 m 1 km 121 73 45 46 30 144 103 37 10 4 Asymmetric 250 ft 1000 ft 2,000 ft 3,000 ft 3,500 ft 76 m 305 m 610 m 914 m 1 km 168 126 60 42 35 95 54 21 6 1 Note The actual distance and link performance may vary depending on the environment and type/gauge of wire used.
NOTES _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ __________________________________________
NOTES _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ __________________________________________
Copyright © 2011. Patton Electronics Company All Rights Reserved.