ipRocketLink™ Model 3101 Series ADSL2+ WiFi Four-Port Router Getting Started Guide Important This is a Class B device and is intended for use in a light industrial (commercial) or residential environment. It is not intended for use in a heavy industrial environment. Sales Office: +1 (301) 975-1000 Technical Support: +1 (301) 975-1007 E-mail: support@patton.com WWW: www.patton.com Part Number: 07M3101-GS, Rev.
Patton Electronics Company, Inc. 7622 Rickenbacker Drive GaithersbuModel 3101, MD 20879 USA Tel: +1 (301) 975-1000 Fax: +1 (301) 869-9293 Support: +1 (301) 975-1007 Web: www.patton.com E-mail: support@patton.com Trademark Statement The term ipRocketLink is a trademark of Patton Electronics Company. All other trademarks presented in this document are the property of their respective owners. Copyright © 2010-2011, Patton Electronics Company. All rights reserved.
Summary Table of Contents 1 General Information...................................................................................................................................... 17 2 Applications Overview................................................................................................................................... 23 3 Installation and Initial Configuration ...........................................................................................................
Table of Contents Summary Table of Contents ........................................................................................................................... 3 Table of Contents ........................................................................................................................................... 4 List of Figures ................................................................................................................................................. 9 List of Tables ...
Model 3101 Series Getting Started Guide Table of Contents Logging In.............................................................................................................................................................32 Viewing Device Information .................................................................................................................................33 Summary ...................................................................................................................
Model 3101 Series Getting Started Guide Table of Contents Parental Control Setup ..........................................................................................................................................71 Time Restriction .............................................................................................................................................71 URL Filter ....................................................................................................................
Model 3101 Series Getting Started Guide Table of Contents 7 System Management.................................................................................................................................... 105 Overview .............................................................................................................................................................106 Running Diagnostic Tests .....................................................................................................
Model 3101 Series Getting Started Guide Table of Contents Configuration and Management..........................................................................................................................119 AC Adapter .........................................................................................................................................................119 Environment ......................................................................................................................
List of Figures 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Model 3101 Series front panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Model 3101 rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 3101 application . . . . . . . . . . . . . . . .
Model 3101 Getting Started Guide 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 List of Figures WMI: DNS Server Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 WMI: IPoA Connection Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 3101 Getting Started Guide 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 List of Figures WMI: Storage Device Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 WMI: Storage User Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Tables 1 2 3 General conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 LED Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Port Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About this guide This guide describes how to set up and manage the ipRocketLink™ Model 3101 ADSL2/2+ WiFi Router.
Model 3101 Series Getting Started Guide About this guide Precautions Notes, cautions, and warnings, which have the following meanings, are used throughout this guide to help you become aware of potential problems. Warnings are intended to prevent safety hazards that could result in personal injury. Cautions are intended to prevent situations that could result in property damage or impaired functioning. Note A note presents additional information or interesting sidelights.
Model 3101 Series Getting Started Guide About this guide Safety when working with electricity • Do not open the device when the power cord is connected. For systems WARNING • • • • • • without a power switch and without an external power adapter, line voltages are present within the device when the power cord is connected.
Model 3101 Series Getting Started Guide CAUTION About this guide Electrostatic Discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when electronic printed circuit cards are improperly handled and can result in complete or intermittent failures. Do the following to prevent ESD: • Always follow ESD prevention procedures when removing and replacing cards. • Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact.
Chapter 1 General Information Chapter contents Model 3101 Series Overview .................................................................................................................................18 Features ..........................................................................................................................................................18 Models ...................................................................................................................................
Model 3101 Series Getting Started Guide 1 • General Information Model 3101 Series Overview Patton’s Model 3101 Series ipRocketLink™ ADSL2/2+ bridge/routers are the perfect choice for users or service providers who need triple-play ready ADSL CPE with advanced routing functionality. Based on International Telecommunications Union (ITU) and American National Standard Institute (ANSI) standards G.992.1, G.992.2, G.992.3, G.992.5 and ANSI T1.
Model 3101 Series Getting Started Guide 1 • General Information Front Panel Model 3101/4IWU ipRocketLink ADSL2+ Router Power Line 4 Data 3 2 1 WLAN WPS USB LAN Model 3101/4I ipRocketLink ADSL2+ Router Power Data Line 4 3 2 1 LAN Model 3101/1I ipRocketLink ADSL2+ Router Power Data Ethernet Line Figure 1. Model 3101 Series front panels LEDs Table 2. LED Descriptions LED Power Color Status Green On Red Data Green Green Red Ethernet (1-4) Green The software is upgrading.
Model 3101 Series Getting Started Guide 1 • General Information Table 2. LED Descriptions LED Color Status WLAN (/4IWU model only) Green On Blink WPS (/4IWU model only) Green USB (/4IWU model only) Green WLAN is enabled. Data is being transmitted through the WiFi. Off WLAN is disabled. On Connection succeeds under WiFi Protected Setup. Blink Negotiation is in progress under WiFi Protected Setup. Off WiFi Protected Setup is disabled. On A 3G or USB connection has been established.
Model 3101 Series Getting Started Guide 1 • General Information Rear Panel Model 3101/4IWU Line Reset WLAN WPS Eth 1 Eth 2 Eth 3 USB Eth 4 Power Model 3101/4I Line Reset Eth 1 Eth 2 Eth 3 Eth 4 Power Model 3101/1I Power Reset Ethernet Line Figure 2.
Model 3101 Series Getting Started Guide Ports 1 • General Information Table 3. Port Descriptions Port Description Interface for connecting antennas Line RJ-11 port for connecting to ADSL telephone line WLAN WLAN switch for enabling/disabling the WLAN function Reset You may need to reset the Model 3101 if you lose network connectivity or if you can no longer communicate with the Model 3101 via the web interface.
Chapter 2 Applications Overview Chapter contents Typical applications...............................................................................................................................................
Model 3101 Series Getting Started Guide 2 • Applications Overview Typical applications You may use the Model 3101 for the following applications: • Home gateway • SOHO applications • Small enterprise applications • Higher data rate broadband sharing • Audio and video streaming and transfer • PC file and application sharing • Network and online gaming The Model 3101excels in manageability: • NetLinkPlug-and-play automatically facilitates remote unit configuration using standard ADSL CAC.
Chapter 3 Installation and Initial Configuration Chapter contents Installation Overview.............................................................................................................................................26 Planning the Installation........................................................................................................................................26 Location requirements .............................................................................................
Model 3101 Series Getting Started Guide 3 • Installation and Initial Configuration Installation Overview The Model 3101 maintains several separate interfaces– Ethernet LAN, ADSL (WAN), and a wireless LAN interface. Planning the Installation Location requirements Place the 3101 in a location where it can be connected to the various devices as well as to a power source. The 3101 should not be located where it will be exposed to moisture or excessive heat.
Model 3101 Series Getting Started Guide 3 • Installation and Initial Configuration Installing the Model 3101 Do not work on the system or connect or disconnect cables during periods of lightning activity. WARNING Do not place any objects on top of or near the vent holes on the Model 3101 case.
Model 3101 Series Getting Started Guide 3 • Installation and Initial Configuration Resetting the Model 3101 You may press the Reset button while the unit is on to reset to the original factory settings. Use a ballpoint pen or paper clip to gently push the reset button. Remember that this will delete any settings stored in flash memory including user account information and LAN IP settings. The device settings will be restored to the factory default IP address 192.168.1.1 and the subnet mask 255.255.255.0.
Model 3101 Series Getting Started Guide 3 • Installation and Initial Configuration Setting Up the 3101 for Configuration Connecting your computer or home network to the 3101 is a simple procedure, varying slightly depending on your operating system. This chapter will help you to seamlessly integrate 3101 with your computer or home network. The Windows default network settings dictate that in most cases the setup procedure described below will be unnecessary.
Model 3101 Series Getting Started Guide 3 • Installation and Initial Configuration PC Network Configuration Each network interface on the PC should either be configured with a statically defined IP address and DNS address, or should be instructed to automatically obtain an IP address using the Network DHCP server. 3101 provides a DHCP server on its LAN and it is recommended to configure your LAN to obtain its IP and DNS server IP automatically.
Chapter 4 Device Access and Information Chapter contents Overview ...............................................................................................................................................................32 Logging In.............................................................................................................................................................32 Viewing Device Information .....................................................................................
Model 3101 Series Getting Started Guide 4 • Device Access and Information Overview This chapter describes how to access the Model 3101 Series Web Management Interface (WMI), which allows you to configure and control all of the 3101 features and system parameters, using a user-friendly graphical interface. This user-friendly approach is also implemented in the WMI's documentation structure, which is based directly on the WMI's structure.
Model 3101 Series Getting Started Guide 4 • Device Access and Information Viewing Device Information The Device Info section of the WMI provides an overview of the unit’s interface statistics, connection status, and routes. Summary Click Device Info > Summary (Figure 7 on page 32) to view the unit’s software versions and DSL status: Board ID, Software Version, and the information of your WAN connection such as the upstream rate and the LAN IPv4 address.
Model 3101 Series Getting Started Guide 4 • Device Access and Information WAN In the Device Info > Statistics menu, click WAN (Figure 10) to view the WAN interface statistics. You can query information on packets recevied on the WAN interfaces. Click Reset Statistics to return the values to zero. Figure 10. WMI: WAN Statistics xTM In the Device Info > Statistics menu, click xTM (Figure 11) to view the ATM interface statistics. You can query information on packets recevied on the xTM interfaces.
Model 3101 Series Getting Started Guide 4 • Device Access and Information xDSL In the Device Info > Statistics menu, click xDSL (Figure 12) to view the DSL interface statistics. Figure 12. WMI: xDSL Statistics xDSL BER Test. Click xDSL BER Test on the xDSL Statistics page to run a Bit Error Rate (BER) Test on the DSL line. Select a time from the Tested Time (sec) drop-down menu and click Start to begin the test. The Tested Time choices are: 1, 5, 10, 20, 60, 120, 180, 240, 300, and 360. Figure 13.
Model 3101 Series Getting Started Guide 4 • Device Access and Information Route Click Device Info > Route (Figure 14) to view route table information. Figure 14. WMI: Route Info ARP Click Device Info > ARP (Figure 15) to view MAC and IP information of equipment attached to the 3101. Figure 15. WMI: ARP Info DHCP Click Device Info > DHCP (Figure 15) to view the host name, the IP address assigned by the DHCP server, the MAC address which is corresponding to the IP address, and the DHCP lease time.
Chapter 5 Advanced Configuration Chapter contents Overview ...............................................................................................................................................................39 Layer2 Interface Setup ...........................................................................................................................................39 WAN Service Setup...........................................................................................................
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Policy Routing ................................................................................................................................................78 DSL Setup.............................................................................................................................................................78 Universal Plug & Play (UPnP) Setup .............................................................................
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Overview The Advanced Setup section of the WMI allows you to configure features (see figure 17) for the 3101. Figure 17. Advanced Setup Menu Layer2 Interface Setup Click Advanced Setup > Layer2 Interface > ATM Interface (Figure 21) to configure, modify, and remove DSL ATM interfaces. Figure 18. WMI: DSL ATM Interface Configuration In the main DSL ATM interface list, you can click Add to configure a new ATM PVC identifier. Figure 19.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration On the ATM PVC Configuration page, you can set the VPI and VCI values, elect the DSL latency, link type (EoA is for PPPoE, IPoE, and Bridge.), connection mode, encapsulation mode, service category, and IP QoS scheduler algorithm. • VPI (Virtual Path Identifier): The virtual path between two points in an ATM network, and its valid value is from 0 to 255.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration • “PPP over Ethernet (PPPoE)” on page 41 • “MAC Encapsulation Routing (MER) (IPoE)” on page 45 • “PPP over Ethernet (PPPoE)” on page 41 • “IP over ATM (IPoA)” on page 52 • “Bridging” on page 55 PPP over Ethernet (PPPoE) To create a new PPPoE connection: 1. Click Add from the main WAN service page to configure a new connection. (Before you can add a new PPPoE service, make sure that you have created a proper ATM PVC configuration.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration 3. On the PPP Username and Password page, provide information for the PPP username, password, service name, and authentication method. Figure 24. WMI: PPP Information – PPP Username: The valid username provided by your ISP. – PPP Password: The valid password provided by your ISP. – PPPoE Service Name: Enter the service name provided by your ISP. If the ISP does not provide a service name, do not enter any information.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration – Use Static IPv6 Address: If enabled, the 3101 uses this IP as the WAN IP address. If disabled, the 3101 obtains an IP address assigned through uplink equipment. – Enable IPv6 Unnumbered Model: Enable or disable this function. – Enable PPP Debug Mode: Enable or disable this function. – Bridge PPPoE Frames Between WAN and Local Ports: Enable or disable this function.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration 5. On the DNS Configuration page (Figure 26) you may obtain the DNS server addresses from the selected WAN interface or manually enter the static DNS server addresses. If only a PVC with IPoA or static MER protocol is configured, you must manually enter the static DNS server addresses. Click Next to continue. Figure 26. WMI: DNS Server Configuration 6.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration MAC Encapsulation Routing (MER) (IPoE) To create a new MER WAN service: 1. Click Add from the main WAN service page to configure a new connection. (Before you can add a new PPPoE service, make sure that you have created a proper ATM PVC configuration. See figure 19 on page 39). The following page displays. Click Next to continue. Figure 28. WMI: Select Layer2 Interface 2.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Figure 30. WMI: WAN IP Settings 4. On the Network Address Translation Settings page (Figure 31), you may modify NAT Settings and select to enable IGMP Multicast. – Enable NAT: Select to enable the NAT functions of the 3101. If you do not enable NAT, you must add a route on the uplink equipment; otherwise, the access to the Internet will fail. It is recommended to enable NAT. – Enable Firewall: Enable/disable IP filtering.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration 5. On the Routing-Default Gateway page (Figure 25), select a preferred WAN interface as the system default gateway. Click Next to continue. Figure 32. WMI: Routing - Default Gateway 6. On the DNS Configuration page (Figure 26) you may obtain the DNS server addresses from the selected WAN interface or manually enter the static DNS server addresses.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration 7. The final connection configuration page (Figure 34) shows an summary of the IPoE settings. Click Save to keep your settings. You will need to reboot the unit to activate this WAN service. Figure 34. WMI: MER (IPoE) Connection Summary PPP over ATM (PPPoA) To create a new PPPoA connection: 1. Click Advanced Setup > Layer2 Interface > ATM Interface to configure, modify, and remove DSL ATM interfaces.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration 3. Click Add from the main WAN service page to configure a new connection. The following page displays. Click Next to continue. Figure 36. WMI: Select Layer2 Interface 4. On the Service Configuration page (Figure 23), modify the service description. Click Next to continue. Figure 37. WMI: PPPoA Service Description 5.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration – PPP Username: The valid username provided by your ISP. – PPP Password: The valid password provided by your ISP. – Authentication Method: Select from AUTO, PAP, CHAP, MSCHAP. (Default = AUTO) – Enable Fullcone NAT: With NAT, all requests from the same internal IP address and port are mapped to the same external IP address and port.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration 7. On the DNS Configuration page (Figure 26) you may obtain the DNS server addresses from the selected WAN interface or manually enter the static DNS server addresses. If only a PVC with IPoA or static MER protocol is configured, you must manually enter the static DNS server addresses. Click Next to continue. Figure 40. WMI: DNS Server Configuration 8.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration IP over ATM (IPoA) To create a new IPoA connection: 1. Click Advanced Setup > Layer2 Interface > ATM Interface to configure, modify, and remove DSL ATM interfaces. In the main DSL ATM interface list, you can click Add to configure a new ATM PVC identifier for PPPoA mode. Figure 42. WMI: ATM PVC Configuration 2.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration 4. On the Service Configuration page (Figure 44), modify the service description. Click Next to continue. Figure 44. WMI: IPoA Service Description 5. On the WAN IP Settings page, enter the WAN IP address and the WAN subnet mask provided by your ISP. Click Next to continue. Figure 45. WMI: WAN IP Settings 6. On the Network Address Translation Settings page (Figure 46), you may modify NAT Settings and select to enable IGMP Multicast.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration 7. On the Routing-Default Gateway page (Figure 47), select a preferred WAN interface as the system default gateway. Click Next to continue. Figure 47. WMI: Routing - Default Gateway 8. On the DNS Configuration page (Figure 48) you should use a static DNS IP address for IPoA mode. Select the proper DNS server interface and enter the primary DNS server and the secondary DNS server. Click Next to continue. Figure 48.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration 9. The final connection configuration page (Figure 49) shows an summary of the IPoA connection. Click Save to keep your settings. You will need to reboot the unit to activate this WAN service. Figure 49. WMI: IPoA Connection Summary Bridging To create a new bridge connection: 1. Click Add from the main WAN service page to configure a new connection.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration 2. On the Connection Type page (Figure 51), select the radio button for Bridging and select LLC/SNAPROUTING as the Encapsulation Mode. Click Next to continue. Figure 51. WMI: Bridging Connection Type 3. The final connection configuration page (Figure 52) shows an summary of the Bridging connection. Click Save to keep your settings. You will need to reboot the unit to activate this WAN service. Figure 52.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration • Information: Click this button to display the information of the 3G network card. • Upload Driver: For an unsupported USB dongle, click this button to upload the new driver for supporting the USB. The driver is a text file. Click Pin Manage, and the following page displays. Figure 54. WMI: 3G Pin Configuration • Enable PIN protect: If enabled, you need to enter the PIN code when rebooting or inserting the USB.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration In the 3G WAN Service page, you may configure the settings of the 3G USB modem. • Enable USB Modem: f you want to access the Internet through the 3G network card, you must enable the USB modem. • User Name: Username provided by your 3G ISP. • Password: Password provided by your 3G ISP. • Authentication Method: Select a proper authentication method in the drop- down list. You can select Auto, PAP, CHAP, or MSCHAP.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration connection takes priority over the 3G connection. When the DSL WAN connection starts to perform dial-up, the 3G connection will be disconnected. If the DSL WAN connection has established, you may manually perform 3G dial-up, and then the DSL WAN connection will be disconnected. LAN Setup Click Advanced Setup > LAN (Figure 57) to define an IP address for the 3101 and configure the DHCP server. Figure 57.
Model 3101 Series Getting Started Guide Note 5 • Advanced Configuration New settings can only be made after the 3101 has been rebooted. If necessary, reconfigure the IP address on your PC (including one that is statically assigned) so that it matches the new configuration. Enabling IGMP Snooping IGMP snooping enables the router to forward multicast traffic intelligently, instead of flooding all ports in the VLAN.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Editing the DHCP Option Click the Edit DHCP Option button in the Local Area Network (LAN) Setup page to display the DHCP Option Setup page. On this page, you can add, edit or delete the DHCP options, and these options will be sent to the DHCP client. Figure 60. WMI: DHCP Option Editing the DHCP Option 60 Click the Edit DHCP Option 60 button in the Local Area Network (LAN) Setup page to display the DHCP Option Setup 60 page.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Configuring the second IP address and subnet mask for a LAN interface On the Local Area Network (LAN) Setup page, you are allowed to set the second IP address and the subnet mask for a LAN interface. Figure 64. WMI: Second IP Address for LAN Interface After enabling the second IP Address and Subnet Mask for LAN interface option, enter an IP address and a subnet mask for the LAN interface.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration lyzing received MLD messages, a Layer 2 device running MLD Snooping establishes mappings between ports and multicast MAC addresses and forwards IPv6 multicast data based on these mappings. Click the Save/Apply button to apply the settings. Network Address Translation (NAT) Setup Virtual Servers The firewall can prevent unexpected traffic on the Internet from your host on the LAN.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration • Use interface: Select an interface that you want to configure. • Select a Service: Select a proper service in the drop-down list. • Custom Server: Enter a new service name to establish a user service type. • Server IP Address: Assign an IP address to virtual server. • External Port Start: When selecting a service, the port number will automatically be displayed. You can modify it if necessary.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Click the Add button to display the Port Triggering Configuration page. Figure 69. WMI: Adding a Port Triggering Entry • Use interface: Select an interface that you want to configure. • Select an application: Select a proper application in the drop-down list. • Custom application: Manually define an application. • Trigger port Start:The start port number that LAN uses to trigger the open port.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration DMZ Host DMZ allows all the ports of a PC on your LAN to be exposed to the Internet. Set the IP address of the PC to be DMZ host, so that the DMZ host will not be blocked by firewall. Click Advanced Setup > NAT > DMZ Host to configure the DMZ host. Figure 70. WMI: NAT > DMZ Host Enter the IP address of the DMZ host and click the Apply/Save button.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Security Setup Click Advanced Setup > Security to manage IP filtering and MAC filtering for the 3101. By default, the firewall is enabled. The firewall is used to block the file transmission between the Internet and your PC. It serves as a safety guard and permits only the authorized files to be sent to the LAN. Note If the 3101 is configured for bridge mode, IP filtering is disabled and the IP filtering interface does not display.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration • Source IP Address: Enter an IP address that the outgoing packet (protocol-selected packet) will block. • Source Port: UPD/TCP source port or a range of ports. • Destination IP Address: The destination IP address of the exterior network. • Destination Port: UPD/TCP destination port or a range of ports. Incoming Click on Incoming under IP Filtering in the Security menu to configure incoming IP filtering rules.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration • Filter Name: Enter the name of incoming filter rule. • IP Version: Select the proper IP version from the drop-down list. • Protocol: Select one: TCP/UDP, TCP, UDP, or ICMP. • Source IP Address: Enter an IP address that the incoming packet (protocol-selected packet) will allow. • Source Port: UPD/TCP source port or a range of ports. • Destination IP Address: The destination IP address of the exterior network.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration FORWARDED means that all MAC layer frames will be forwarded except for packets that match any of the specified rules in the following table. BLOCKED means that all MAC layer frames will be blocked except for packets that match any of the specified rules in the following table. Figure 78. WMI: MAC Filtering To change the MAC Filtering Global Policy from FORWARDED to BLOCKED, click Change Policy.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Click Add to create a new MAC filter rule. The Add MAC Filter page displays (Figure 80). Figure 80. WMI: Adding a MAC Filter To create a new MAC filter, provide information for the following parameters: • Protocol Type: Select one: PPPoE, IPv4, IPv6, AppleTalk, IPX, NetBEUI or IGMP. • Destination MAC Address: Enter the MAC address of the destination. • Source MAC Address: Enter the MAC address of the source.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Figure 82. WMI: Adding an Access Time Restriction Policy • User Name: The name of the user you want to prevent from accessing the unit. • Browser’s MAC Address: The MAC address of the LAN device where the browser is currently running (default setting). • Other MAC Address: The MAC address of a different LAN device you want to restrict. (To find out the MAC address of a Windows-based PC, enter ipconfig /all in the PC’s command window).
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Figure 84. WMI: URL Filter Setup On the Add URL Filter page, enter the URL address and the corresponding port number. For example, enter the URL address http://www.google.com and the port number, then click the Apply/Save button. The following page displays: Figure 85. WMI: Completing a URL Filter Entry Quality of Service (QoS) Setup Click Advanced Setup > Quality of Service to manage traffic for the 3101.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Figure 86. WMI: Enable QoS Queue Configuration Click Queue Config (Figure 87) in the Quality of Service menu to add or remove a QoS rule. The lower integer value for precedence indicates the higher priority. Figure 87.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Click Add on the QoS Queue Setup page to create a new queue entry and assign it to a specific network interface. Figure 88. WMI: Add QoS Queue Entry • Name: nter the name of QoS queue. • Enable: Enable or disable the QoS queue. • Interface: Select the proper interface for the QoS queue. Click Apply/Save to save and activate the queue.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Figure 90. WMI: Add Network Traffic Class Rule Routing Setup Click Advanced Setup > Routing to manage the default gateway, static route, and Routing Information Protocol (RIP) settings.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Default Gateway The Routing–Default Gateway page (Figure 91) is the default page that displays when you click on Routing in the Advanced Setup menu. From this page, you can modify the default gateway settings. Select a proper WAN interface in the list of Available Routed WAN Interfaces as the system default gateway. Click Apply/ Save to activate any changes. Figure 91.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration • Gateway IP Address: The next-hop IP address. • Metric: The metric value of routing. Click Apply/Save to apply the settings. Policy Routing Click Routing > Policy Routing to add or remove a static policy rule. Click the Add button to enter the policy name, source IP and default gateway, and select the physical LAN port and interface on the Policy Routing Setup page (Figure 93). Click the Apply/Save button to save the configuration.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Universal Plug & Play (UPnP) Setup Click Advanced Setup > UPnP to activate the UPnP capability on the 3101. PCs with UPnP (Universal Plug & Play) can offer their own network services and automatically use services offered in the network. Click Apply/Save to activate any changes. Figure 95. WMI: UPnP Configuration Domain Name System (DNS) Proxy Setup Click Advanced Setup > DNS Proxy to configure the DNS proxy function.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Packet Acceleration Setup Click Advanced Setup > Packet Acceleration (Figure 98) to enable packet flow accelerator. Click Apply/Save to activate any changes. Figure 98. WMI: Packet Acceleration Storage Service Setup Storage Device Info Click Advanced Setup > Storage Service > Storage Device Info to display information about the storage device that connects to the DSL router. Figure 99.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Interface Grouping Setup Click Advanced Setup > Interface Grouping to configure mapping groups. Figure 102. WMI: Interface Grouping Entries Interface grouping supports multiple ports to PVC and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with the appropriate LAN and WAN interfaces using the Add button.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Figure 103.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration IPSec Setup Click Advanced Setup > IPSec to configure IPSec tunnel mode connections. Figure 104. WMI: IPSec Tunnel Connections Click the Add button to display the IPSec Settings page. Enter information for the IPSec connection name, tunnel mode, and remote IPSec gateway address. If you need to configure the advanced settings of this IPSec tunnel connection, click the Show Advanced Settings button to display more configuation options.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Certificate Setup Click Advanced Setup > Certificate to request or import a certificate to help identify your device to other devices or verify certificates from other devices. Local Certificates The Local Certificates page (Figure 106) is the default page that displays when you click on Certificate in the Advanced Setup menu. Local certificates are used by peers to verify your identity.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration • State/Province Name: Enter the name of the state or province where your organization's head office is located. Provide the full name of the state or province. • Country/Region Name: Select the two-letter ISO abbreviation for your country (for example, GB for the United Kingdom). Click Apply to generate the certificate request. Wait several seconds while the system creates the request.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Import Certificate On the Local Certificates page, click Import Certificate (Figure 110) to paste an existing certificate and private key. Figure 110. WMI: Import Local Certificate Click Apply to add the certificate. Trusted CA Certificates Click Certificate > Trusted CA to display the Trusted CA (Certificate Authority) Certificates page. CA certificates are used by the 3101 to verify peers' certificates.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Click Import Certificate (Figure 112) to paste an existing certificate. Click Apply to add the certificate. Figure 112. WMI: Import CA Certificate Power Management Click Advanced Setup > Power Management to control hardware modules and power consumption. Figure 113. WMI: Power Management Use the radio buttons to select desired options. Click Apply to save the settings.
Model 3101 Series Getting Started Guide 5 • Advanced Configuration Multicast Setup Click Advanced Setup > Multicast to configure the multicast parameters of the IPv4 and IPv6. Click Apply/ Save to apply the settings. Figure 114.
Model 3101 Series Getting Started Guide Multicast Setup 5 • Advanced Configuration 89
Chapter 6 Wireless Configuration Chapter contents Overview ...............................................................................................................................................................91 Basic Wireless Setup ..............................................................................................................................................91 Wireless Security Setup....................................................................................................
Model 3101 Series Getting Started Guide 6 • Wireless Configuration Overview Click Wireless in the navigation menu to view wireless configuration options for the 3101.
Model 3101 Series Getting Started Guide 6 • Wireless Configuration • Enable Wireless: If you want to make wireless available, you must check this box first. Otherwise, the Hide Access Point SSID, Country, Enable Wireless Guest Network, and Guest SSID box will not be displayed. • Enable Autogeneration: After enabling this function, it will automatically set the SSID and the encryption mode.
Model 3101 Series Getting Started Guide 6 • Wireless Configuration Wireless Security Setup Click Security in the Wireless menu to configure security features of the wireless LAN for the 3101. The Wireless -- Security page displays (Figure 116). On this page, you can configure the network security settings through the Wi-Fi Protected Setup (WPS) method (see “WPS Setup” on page 94) or by setting the network authentication mode (see “Manual Setup AP” on page 94). Click Apply/Save to activate any changes.
Model 3101 Series Getting Started Guide 6 • Wireless Configuration WPS Setup Figure 117. WMI: WPS Configuration There are 2 primary methods used in the Wi-Fi Protected Setup (WPS): • PIN entry, a mandatory method of setup for all WPS certified devices • Push button configuration (PBC), an actual push button on the hardware or through a simulated push button in the software. (This is an optional method on wireless client).
Model 3101 Series Getting Started Guide 6 • Wireless Configuration Provide information for the following parameters: • Select SSID: Select the wireless LAN SSID to configure security features. • Network Authentication: Select the authentication mode for the selected SSID. Authentication configuration fields display automatically when you select a mode from this menu.
Model 3101 Series Getting Started Guide 6 • Wireless Configuration 802.1X When you select 802.1X as the Network Authentication mode (Figure 120), you are required to enter information for the RADIUS server. RADIUS server is short for a Remote Authentication Dial-in User Service server, which is most commonly a third party server, used for authenticating wireless clients that want to connect to an access point.
Model 3101 Series Getting Started Guide 6 • Wireless Configuration WPA When you select WPA as the Network Authentication mode (Figure 121), provide information for the following parameters: Figure 121. WMI: Wireless Security – WPA Authentication Mode • WPA Group Rekey Interval: Enter a value for the time that the WPA key must change. If the value is set to 0, the change is done automatically between the server and the client. • RADIUS Server IP Address: Enter the IP Address of the authentication server.
Model 3101 Series Getting Started Guide 6 • Wireless Configuration WPA-PSK, WPA2-PSK, or Mixed WPA2/WPA-PSK When you select WPA-PSK, WPA2-PSK, or Mixed WPA2/WPA-PSK as the Network Authentication mode (Figure 122), provide information for the following parameters: Figure 122. WMI: Wireless Security – WPA-PSK Authentication Mode • WPA/WAPI passphrase: Enter the password for WPA station. • WPA Group Rekey Interval: Enter a value for the time that the WPA key must change.
Model 3101 Series Getting Started Guide 6 • Wireless Configuration WPA2 or Mixed WPA2/WPA When you select WPA2 or Mixed WPA2/WPA as the Network Authentication mode (Figure 123), provide information for the following parameters: Figure 123. WMI: Wireless Security – Mixed WPA2/WPA Authentication Mode • WPA2 Preauthentication: Select to enable or disable preauthentication. • Network Re-auth Interval: Specify the timer of re-authentication between the server and the client.
Model 3101 Series Getting Started Guide 6 • Wireless Configuration MAC Filter Setup Click MAC Filter in the Wireless menu to allow or reject access to the wireless network for wireless clients.The Wireless -- MAC Filter page displays (Figure 124). From this page, you can create a list of MAC addresses that are banned from accessing the 3101or allowed to associate with the 3101. Figure 124.
Model 3101 Series Getting Started Guide 6 • Wireless Configuration Wireless Bridge Setup Click Wireless Bridge in the Wireless menu to configure wireless bridge features for the 3101. The Wireless - Bridge page displays (Figure 125). The Wireless Distribution System (WDS) allows you to extend the range of your wireless network by introducing one or more WDS-enabled devices into your wireless network. You can only establish WDS links with WDS-enabled devices. Figure 125.
Model 3101 Series Getting Started Guide 6 • Wireless Configuration Advanced Wireless Setup Click Advanced in the Wireless menu to configure advanced wireless features for the 3101. The Wireless -Advanced page displays (Figure 126). Usually, you do not need to change the settings on this page. Click Apply/Save to activate any changes. Figure 126. WMI: Advanced Wireless Configuration Provide information for the following parameters (as needed): • Band: Select 802.11b/g using wireless frequency band range.
Model 3101 Series Getting Started Guide 6 • Wireless Configuration • Channel: Select the appropriate channel to correspond with your network settings. All devices in your wireless network must use the same channel in order to work correctly. The 3101 supports auto channeling functionalty. • Auto Channel Timer: Specify the time limit (in minutes) for auto channeling. • 802.11n/EWC: Select disable 802.11n or Auto. • Bandwidth: Select the bandwidth for the network.
Model 3101 Series Getting Started Guide 6 • Wireless Configuration beacon) before sending the beacon again. The beacon interval may be adjusted in milliseconds (ms). The default value (100) is recommended. • XPress Technology: Select Enable or Disable. This feature is special acceleration technology for IEEE802.11g. The default is Disabled. • Transmit Power: Adjust the transmission range. This tool can be helpful for security purposes if you want to limit the transmission range.
Chapter 7 System Management Chapter contents Overview .............................................................................................................................................................106 Running Diagnostic Tests ...................................................................................................................................106 Managing System Settings ..............................................................................................................
Model 3101 Series Getting Started Guide 7 • System Management Overview This chapter provides information on testing connections and configuring typical system settings. For information about testing the DSL connection for the unit, see “Running Diagnostic Tests” on page 106. For information about configuring device settings, see “Managing System Settings” on page 106. Running Diagnostic Tests Click Diagnostics in the navigation menu to test the DSL connection for the 3101.
Model 3101 Series Getting Started Guide 7 • System Management Settings Click Settings in the Management menu to backup, restore, and update system configuration files. Backup Click Backup under Settings in the Management menu to create a backup file of the current configuration. Click Backup Settings (Figure 129) to display the Save File prompt. Select the location to save the backup file and click OK. Figure 129.
Model 3101 Series Getting Started Guide 7 • System Management System Log Click System Log in the Management menu to view and configure logging for the 3101. The System Log page displays (Figure 132). Figure 132. WMI: System Log Click View Security Log to view and configure security logging for the 3101. Click the Close button to exit. Figure 133. WMI: Security Log From the System Log page, click Configure System Log to modify log options. The System Log Configuration page displays (Figure 134).
Model 3101 Series Getting Started Guide 7 • System Management Click View System Log to view and configure logging for the 3101. Click the Close button to exit. Figure 135. WMI: System Log TR-069 Client Click TR-069 Client in the Management menu to manage ACS (Auto Configuration Server) connections and other stand-alone routers and LAN-side client devices. The TR-069 Client Configuration page displays (Figure 136). Click Apply/Save to activate any changes. Figure 136.
Model 3101 Series Getting Started Guide 7 • System Management Access Control The Access Control options in the Management menu allow you to enable/disable services and change passwords. Services Click Services under Access Control in the Management menu to enable and disable LAN and WAN services (Figure 137). Supported services for LAN/WAN include: FTP, HTTP, ICMP, SSH, TELNET and TFTP. Click Apply/Save to activate any changes. Figure 137.
Model 3101 Series Getting Started Guide 7 • System Management Update Software Click Update Software in the Management menu to update the firmware for the 3101(Figure 139). Click Browse to select the new software image file. Click Update Software to apply the update. Wait a few minutes while the 3101 reboots. Note While the software update is in progress, do not shut down the router. After the software update completes, the router automatically reboots.
Chapter 8 Contacting Patton for assistance Chapter contents Introduction ........................................................................................................................................................113 Contact information............................................................................................................................................113 Patton support headquarters in the USA ...............................................................................
Model 3101 Series Getting Started Guide 8 • Contacting Patton for assistance Introduction This chapter contains the following information: • “Contact information”—describes how to contact Patton technical support for assistance. • “Warranty Service and Returned Merchandise Authorizations (RMAs)”—contains information about the RAS warranty and obtaining a return merchandise authorization (RMA). Contact information Patton Electronics offers a wide array of free technical services.
Model 3101 Series Getting Started Guide 8 • Contacting Patton for assistance Out-of-warranty service Patton services what we sell, no matter how you acquired it, including malfunctioning products that are no longer under warranty. Our products have a flat fee for repairs. Units damaged by lightning or other catastrophes may require replacement.
Appendix A Compliance Chapter contents Compliance .........................................................................................................................................................116 EMC .............................................................................................................................................................116 Low-Voltage Directive (Safety) .............................................................................................................
Model 3101 Series Getting Started Guide A • Compliance Compliance EMC • EN55022, Class B • EN55024 • EN61000-3-2 • EN61000-3-3 Low-Voltage Directive (Safety) • IEC/EN60950-1, 2nd Edition PSTN • This device is not intended nor approved for connection to the PSTN CE Notice (Declaration of Conformity) Patton Electronics, Inc declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Appendix B Specifications Chapter contents Ethernet Interface................................................................................................................................................118 WiFi Interface .....................................................................................................................................................118 ADSL Interface.........................................................................................................................
Model 3101 Series Getting Started Guide B • Specifications Ethernet Interface Model 3101/1I: One 10/100 Base-TX Ethernet port, IEEE 802.3/3u Model 3101/4I: 4-port 10/100 Base-TX Ethernet port, IEEE 802.3/3u Model 3101/4IWU: 4-port 10/100 Base-TX Ethernet port, IEEE 802.3/3u; One USB 2.0 device port, type B connector WiFi Interface IEEE 802.
Model 3101 Series Getting Started Guide B • Specifications Point-to-Point Protocol (including PPPoA and PPPoE) and user authentication via PAP or CHAP TCP, UDP, ARP, RARP, IPCP, ICMP, IGMP IP routing: static route, RIP v1 and v2 NAT/PAT with extensive ALG supports DNS relay agent; Layer 2 tunneling protocol (L2TP) Security Built-in firewall with protection against DOS attacks with blacklisting, IP spoofing, and other common types of attacks Packet filtering at MAC layer (raw filter) and IP layer, includi
