USER MANUAL MODEL 1058 VLINK Modem Part# 07M1058-B Doc# 058091UB Revised 6/10/02 An ISO-9001Certified Company SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007
1.0 1.1 1.2 1.3 1.4 1.5 Warranty Information ................................................................. Radio and TV Interference............................................................ CE Notice...................................................................................... FCC Part 68 (1058DV Only) ......................................................... Industry Canada Notice ................................................................ Service.......................................
1.0 WARRANTY INFORMATION Patton Electronics warrants all Model 1058 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of the shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not performs as warranted, your sole recourse shall be repair or replacement as described above.
1.3 FCC PART 68 (1058DV ONLY) The Model 1058D is not intended to be connected to the public telephone network. Caution The VLINK port is not intended to be connected to the public telephone network. The 1058DV contains a POTS/ISDN connection that can be connected to the public telephone network. Caution This equipment complies with Part 68 of the FCC Rules. Please note the following: 1. You are required to request service from the telephone company before you connect the Model 1058DV to a network.
3. If your Model 1058DV causes harm to the telephone network, the telephone company may temporarily discontinue your service. If possible, they will notify you in advance, but if advance notice is not practical, you will be notified as soon as possible and will be informed of your right to file a complaint with the FCC. 4. If you experience trouble with the Model 1058DV, please contact Patton Electronics Company for service or repairs. Repairs should be performed only by Patton Electronics Co. 5.
2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for one year for parts and labor. If any questions or problems arise during installation or use of this product, contact Patton Electronics Technical Support at +1 (301) 975-1007. 2.
automatically add and delete MAC addresses, only passing packets across the VDSL link that are meant for the remote peered LAN. Figure 1. Typical application The 1058DV/CO and 1058DV/CP work together to create a transparent extension between two peered Ethernet LANs. POTS/ISDN calls can be made over a VDSL link without interfering with the data. Figure 1 shows a typical point-to-point application.
3.0 INSTALLATION Because the Model 1058 requires no configuration, it can be installed quickly. If you are installing a standalone unit, refer to section 3.1 “Standalone unit installation”. Otherwise, refer to section 3.2 “Rack card installation”. 3.1 STANDALONE UNIT INSTALLATION Do the following: 1. Connect the line interface between the units (refer to section 3.3, “Connecting the Twisted-Pair Line Interface” on page 10) Note See Figure 2 for the standalone unit’s rear panel arrangements. 2.
2. Secure the rear card using the supplied metal screws. 3. Slide the front card into the chassis until you feel resistance as the front card engages the rear card. When that happens, gently push the front card forward until it is fully seated in the card-edge receptacle of the rear card (it should click into place). 4. Secure the front card using the captive fasteners.
3.3 CONNECTING THE TWISTED-PAIR LINE INTERFACE The Model 1058 supports communication between two peer Ethernet LAN sites over a distance of up to 4,652 ft (1,418 m) over 24 AWG (0.5 mm) twisted-pair wire. Note Actual distance and link performance may vary depending on the environment and type/gauge of wire used. Follow the steps below to connect the Model 1058 VDSL Interfaces. Note The Model 1058 units work in pairs.
A de in the US Ma r we Po K LIN V et rn he Et RING TIP Figure 5. Model 1058D (Terminal Block) twisted pair line interface. 3.4 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE The shielded RJ-45 port labeled Ethernet is the 10/100Base-T interface. This port is designed to connect directly to a 10/100Base-T network. Figure 6 shows the signal/pin relationships on this interface. You may connect this port to another Ethernet device via a Type 4 or Type 5 cable that is up to 328 ft long.
straight-through RJ-45 cable. Figure 7 diagrams the cable wiring for connecting the Model 1058 to a 10/100Base-T hub. 1058 10/100Base-T Port RJ-45 Pin No. 10/100Base-T Hub RJ-45 Pin No. 1 (TX+)--------------------------------------------------1 (RX+) 2 (TX-)---------------------------------------------------2 (RX-) 3 (RX+)--------------------------------------------------3 (TX+) 6 (RX-)---------------------------------------------------6 (TX-) Figure 7.
work. The RJ-45 connector in the model 1058’s POTS/ISDN interface is wired as shown in Figure 9. 1 (no connection) 2 (no connection) 1 2 3 4 5 6 7 8 3 (no connection) 4 (2-wire RING) 5 (2-wire TIP) 6 (no connection) 7 (no connection) 8 (no connection) Figure 9. Model 1058DV (RJ-45) POTS/ISDN interface 3.6 CONNECTING POWER An external AC or DC power supply is available separately. This connection is made via the barrel jack on the rear panel of the Model 1058.
4.0 OPERATION Once the Model 1058s are properly installed, they should operate transparently. No user settings required. This section describes reading the LED status monitors. 4.1 POWER UP Before applying power to the Model 1058, please review section 3.6, “Connecting Power” on page 13 to verify that the unit is connected to the appropriate power source. 4.2 FRONT PANEL LED STATUS MONITORS The Model 1058 features five front panel LEDs that monitor power, the Ethernet signals, and the VDSL connection.
V LIN K VL m de Mo r e w Po VLINK Link K IN Power VLINK QOL ink L OL Q E e th Ethernet Link et rn k n Li Ethernet Activity y vit ti Ac Figure 11. Model 1058 rack card front panel Table 1: Front panel LED description LED Power VLINK Link VLINK QOL Ethernet Link Ethernet Activity Description Solid GREEN to indicate the unit is powered on. (Active Green) Solid green (ON) to indicate that the end-to-end VDSL link between the Model 1058s is established.
APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • Shielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet • VDSL Connection: RJ-45 and Terminal Block A.2 TRANSMISSION LINE Two-wire unconditioned twisted pair. A.3 VDSL LINE RATE 12.5 Mbps, symmetric upstream/downstream. A.4 ACTUAL DATA RATE 10 Mbps, symmetric upstream/downstream. A.5 VDSL DISTANCE 4,000 ft (1,219 m) A.6 VDSL SURGE SUPPRESSOR Gas tube with maximum current surge: 20 kA (8120 µs). A.
APPENDIX B MODEL 1058 SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Model # Base Models 1058DRC/CO 1058DRC/CP 1058DVRC/CO 1058DVRC/CP 1058D/CO 1058D/CP 1058D-2PK 1058DV/CO 1058DV/CP 1058DV-2PK 07M1058 Power Supplies 08055DCUI 08055-120-5-1 12V-PSM 24V-PSM 48V-PSM Power Cords* 0805US 0805EUR 0805UK 0805AUS 0805DEN 0805FR 0805IN 0805IS 0805JAP 0805SW Description CO VDSL Rack Card; data only CP VDSL Rack Card; data only CO VDSL Rack Card; voice and data CP VDSL Rack Card; voice and data CO VDSL Mo
APPENDIX C MODEL 1058 SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX• Pin 3: RX+ • Pin 6: RX• Pins 4, 5, 7, 8: no connection C.2 VDSL INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection Terminal Block See Figure 5 on page 11. C.
Copyright © 2001, 2002 Patton Electronics Company All Rights Reserved.
