Monarch 6017 HandiPrint Printer TC6017OI Rev. AB 4/01 ©2000 Monarch Marking Systems, Inc. All rights reserved.
Each product and program carries a respective written warranty, the only warranty on which the customer can rely. Monarch reserves the right to make changes in the product, the programs, and their availability at any time and without notice. Although Monarch has made every effort to provide complete and accurate information in this manual, Monarch shall not be liable for any omissions or inaccuracies. Any update will be incorporated in a later edition of this manual. ©2000 Monarch Marking Systems, Inc.
TABLE OF CONTENTS GETTING STARTED ................................................. 1-1 Unpacking the Printer ............................................ 1-1 Programming Information ....................................... 1-1 Battery and Safety Information................................ 1-2 Installing the Battery .............................................. 1-2 Charging the Battery .............................................. 1-4 Reading the LED ................................................
ii
GETTING STARTED 1 Use these operating instructions with your Monarch 6017 HandiPrint Printer. The printer works with the SYMBOL SPT 1700 or PPT 2700 handheld computer (“handheld”). The printer can print text, bar codes, and limited graphics on thermal direct receipt paper. Use these instructions to ♦ connect the printer ♦ load supplies ♦ charge the battery ♦ clean the printhead.
Battery and Safety Information The printer is powered by a 7.4V Lithium Ion (LiIon) battery. There are no memory effects with LiIon batteries and reconditioning is not required. Lithium ion batteries do not have to be completely drained before charging. ♦ Charging time is approximately 1.5 to 3 hours. ♦ Take the battery out of the printer when storing the printer for long periods of time. ♦ The battery storage temperature is 40 ° F to 104 ° F (4 ° C to 40 ° C).
3. Open the strap at the VELCRO tab and pull the strap through the slot. You now have access to the battery door. Move the strap out of the way. 4. Unlock the battery door by sliding down the battery tab. Tab 5. Open the battery door.
6. Insert the battery into the printer as shown. 7. Press the battery into place. 8. Lock the battery door by pushing up the battery tab. 9. Thread the strap through the slot and secure the strap at the VELCRO tab. Make sure the strap is adjusted to fit your hand. 10. Charge the battery. To remove the battery, open the battery door and tip the battery out of the printer. Charging the Battery The battery can be charged ♦ inside the printer using the AC power adapter provided.
You can print while the battery is charging; however, the battery may not receive a full charge. You can also charge the handheld while it is connected to the printer. However, the batteries (printer and handheld) may not receive a full charge. To print with the AC power adapter connected, you must have a battery inside the printer. 1. Plug the cable into the socket located on the side of the printer as shown (under the symbol). 2. Connect the angle plug into the AC power adapter. 3.
Reading the LED This table explains the LED indicator. LED Indicator LED Indicator Status Red On The charger is charging the battery at a fast rate. If the battery voltage is below 5.0V, the battery is “trickle” charged until the battery reaches 5.0V. The LED is off when the battery is fully charged. Green On Printer is on and ready to accept data. The LED is off when the printer is off and the battery is not charging.
Connecting the Printer Attach the handheld to the printer's 14-pin connector as shown. Cutout 14-Pin Connector Bottom Lip The handheld’s bottom lip fits snugly under the printer’s cutout. If your handheld has a strap, you may remove the strap or keep it attached to the handheld (allows for a more secure fit) before inserting the handheld into the printer. Attaching the Printer’s Strap and Button The printer is shipped with the strap and mounting button already attached.
3. Using the grommet provided, secure the strap into the attaching hole. 4. Thread the strap through the slot and secure the strap at the VELCRO tab. Make sure the strap is adjusted to fit your hand. Self-tapping Phillips screw 5. Button Using the self-tapping Phillips screw provided, secure the button to the strap grommet. The screw threads itself while you tighten it. Make sure the button is securely fastened to the printer. Do not over tighten the screw. You may strip the threads.
LOADING SUPPLIES 2 The printer can print text, bar codes, and some limited graphics on thermal direct receipt paper. See Appendix A, “Specifications” for the width and thickness requirements. 1. Open the supply cover by inserting your fingers into the rubber pull tab and pulling up firmly on the supply cover as shown. Do not pull too hard on the rubber pull tab.
2. Drop the supply into the well. Make sure the supply unwinds from the top as shown. 3. Position the supply between the printhead guides. Printhead Guide Platen Roller 4. Make sure some supply extends past the platen roller. 5. Close the supply cover. Tearing Supply The printer’s supply door acts as a tear bar. Tear down against the tear bar to remove receipts. CAUTION The tear bar may have sharp edges.
USING THE PRINTER 3 This chapter includes information about printing, using the magnetic stripe reader, and scanning bar codes. Printing You must have a printing application installed on your handheld before you can print receipts. Monarch offers a print utility that is free to download from our Web site. Refer to the printing instructions included with your print utility. Make sure your printer’s battery is charged before printing.
Quickly swipe the card through the reader either left-toright or right-to-left with the magnetic stripe in the reader. The magnetic stripe must be facing toward the handheld while it is passed through the reader. Stripe is facing toward handheld The green LED on the printer indicates the following: LED Indicator On Blinks once Off Status Ready/waiting for card. Error reading card’s data. Good swipe (card’s data read). OR Not ready for card.
Scanning Bar Codes Scanning bar codes is application specific. You should only scan a bar code when prompted by your application. 1. Point the scanner at a slight angle approximately four to eight inches from the bar code symbol. Scanner button located on rubber grip 2. You can press either button (on the left and right side of the printer) or both buttons at the same time instead of using the button on the handheld. Scanning buttons are identified by the symbol. 3.
Scanning Tips ♦ Make sure there are no voids in the bar code symbol. ♦ Hold the scanner four to eight inches from the bar code. Move the scanner toward and away from the bar code to find the correct distance for a successful scan. ♦ Aim the scanner at a slight angle to the bar code. ♦ Keep the scanner window clean. ♦ Move to a more dimly lit area if you have several unsuccessful scans. ♦ Direct sunlight may cause unsuccessful scans.
4 CLEANING You may need to clean the printhead and platen roller after printing approximately six rolls of supply, whenever you load new supplies, or when you see voids in the print as shown. CAUTION Do not use sharp objects to clean the printhead. This may damage the printer and require a service charge. 1. Open the supply cover by inserting your fingers into the rubber pull tab and pulling up firmly on the supply cover. 2. Remove the supply roll (when cleaning the printhead). 3.
4. Clean the platen roller with a dry cloth or small brush. You can also use another cotton swab moistened with isopropyl alcohol. Turn the platen roller with your finger and run the cotton swab or dry cloth across it. Make sure the platen roller is clean all the way around. Black Mark Sensor Platen Roller Tear Bar 5. Moisten another cotton swab with isopropyl alcohol. Rub the cotton swab across the black mark sensor to remove any build-up. 6. Moisten another cotton swab with isopropyl alcohol.
TROUBLESHOOTING 5 If you cannot fix a problem, call Technical Support. Problem Action Does not feed or has a paper jam. Remove any jammed supplies. Reload supplies. Does not print. ♦ Check or replace the printer’s battery. ♦ Your handheld’s application may include a query for the battery voltage. Refer to the Programmer's Manual for more information. ♦ Make sure the supplies are loaded correctly and not upside down.
Problem Action Light/heavy printing or voids in printing. Clean the printhead. Check or recharge the battery. See “Charging the Battery” in Chapter 1 for more information. Your System Administrator may need to adjust the print contrast. Your handheld’s application may include a print contrast adjustment. Refer to the Programmer's Manual for more information.
A SPECIFICATIONS Printer Specifications Height: 2.8 inches (71 mm) Width: 4.25 inches (108 mm) Length: 9.5 inches (241 mm) Weight: w/ battery & supply 1.41 lbs. (0.64 kg) Shipping Weight: 3 lbs. (1.4 kg) Power: 7.
Charging Time: Approximately 3 hours with no printing Communications: RS-232 port Print Ratio 25% black maximum per square inch Supply Specifications Supplies: Thermal direct receipt paper Supply Thickness: 2.2 to 3.5 mils (receipt paper) Supply Width: 3.125 inches (79 mm) Supply Length: 1.0 inch (25.4 mm) minimum feed 8.0 inch (203 mm) 1 roll of receipt paper is approximately 600 inches (15,240 mm) Supply Sensing: Black mark (on the face of the supply) Roll Diameters: Inside: .
Using the Optional Stand Read the following if you purchased the optional printer stand. The stand can be ♦ used on a table top or wall-mounted. ♦ adjusted to minimize glare on the handheld’s display ♦ folded flat for storage. For a Table Top: 1. Place the stand on the table top. 2. Unfold the stand and lock into place with the wire bar. 3. Slide the printer into the stand until the button catches in the stand. The button must be attached to the printer. 4.
For Wall-Mounting: Wall-mounting hardware is not included. Use two screws or nails that support at least 5 pounds (2.3 kg.). 1. Place the unfolded stand against the wall. 2. Use a pencil to mark inside the two keyholes for the screws or nails. 3. Attach the screws or nails through the keyholes and into the wall. 4. Slide the printer into the stand until the button catches in the stand. 5.
For supplies, service, or assistance call: 1-800-543-6650 (In the U.S.A.) 021 869 97 70 (In Switzerland) www.gomaro.