Manual

ManualsBrandsPaxton ManualsFor HomeEasyprox compact

Page 1

30/01/2012

Layout

Parts list

Tools List

Power Drill

Drill bits 10 mm, 25 mm

Philips screwdriver

Hacksaw for cutting bolts

Hammer / Mallet

Chisel 25 mm

Stanley knife

Adhesive tape

Pencil

Tape measure

8 mm spanner (supplied)

2 mm Allen key (supplied)

1) Front Lock Assembly

2) Rear Lock Assembly

3) Rubber Escutcheon x2

4) Left and Right Handles

5) Battery Pack

6) Tubular Mortice Lock

7) Spindle

8) 8 mm Conversion Sleeve

9) 2 mm Allen Key

10) 8 mm Spanner

11) Strike Plate Backbox

12) Strike Plate

13) Long Mounting Screws x4

14) Short Mounting Screws x4

This unit is for indoor use only.

Technical Support

Technical help is available: Monday - Friday from 07:00 - 19:00 (GMT)

Saturday from 09:00 - 13:00 (GMT)

01273 811011 support@paxton.co.uk

Ins-30056 Easyprox compact

Documentation on all Paxton products can be found on our website - http://www.paxton.co.uk/

6 7

8 9

10 11 12

Paxton

Summary of content (7 pages)

PAGE 1
30/01/2012 Paxton Ins-30056 Easyprox compact Technical Support 01273 811011 support@paxton.co.uk Technical help is available: Monday - Friday from 07:00 - 19:00 (GMT) Saturday from 09:00 - 13:00 (GMT) Documentation on all Paxton products can be found on our website - http://www.paxton.co.uk/ Layout This unit is for indoor use only.
PAGE 2
Installing the hardware Step 1 - Marking out Decide on the lock height and mark this on the door. Fold the template along one dotted line and tape it to the door with the 'Centreline of Latch' at the required height. Mark the 4 x 10 mm and 1 x 25 mm holes. Remove the template, fold along the other dotted line and apply it to the other side of the door at the same height. Mark the holes as before. Step 2 - Drilling 80 25 57 Drill a 25 mm hole in the door edge at least 80 mm deep to accept the latch.
PAGE 3
Step 5 - Mounting on the door Select the short (doors thinner than 45 mm) or long mounting screws and cut to length if required. (door thickness + 5 mm) Fit the rubber escutcheons to the front and back plates. Present the front and rear lock assembly to the door, locating the square drive in its recess and join the two parts together with 4 mounting screws. Step 6 - Fitting the handles Fit the two handles, positioning the screw holes to the underside and secure with the grub screws provided.
PAGE 4
Enrolment Card - must be presented when the system is first powered on 1 2 3 CA e FUNCTION CARD RD CA e th ON rd to ck TI t ca is cardthis pa this the NC en ent thens in esented by FU rolm ion, presthe tok tokenerprfollow n ate e th TY ard ON rd to ckis TI It McaI t isccardthenis tpathlidthatise the NC OeXn eseennt thn,ensprines prtoesvaenckted.
PAGE 5
Door open time (seconds) 1 2 RD a CA ard when N e c d for s: p IO tim locke follow sto ll CT en or isisunset as wi FUNCTION CARD door open time card The period that the door is unlocked for when a valid token is presented is set as follows: N p do FUoor o that prthese ented d 3 4 ! EP BE P! BEE RD a CA card when for ON me ked lows: p sto TI n ti is unloct as fol ll wi NC pe door is se ing FUoor o that prthese ented periothd e beep ing ep d rio be pe the , d d is rd ire ain rio ca pe en is requ ag
PAGE 6
Commissioning checks With the product fixed securely to the door: 1) Hold the door unlocked by presenting the fail open release card. 2) Check that the handles are running smoothly. This is best done by depressing the handle all the way to the bottom and then releasing it as slowly as possible. If the handle is left behind at any point, it is likely that the product has not been installed squarely enough. Check the handle on both sides of the door.
PAGE 7
Full System Reset The unit is returned to its Factory settings and will require initialising again. 1. Remove the unit from the door by removing the 4 mounting screws on the rear lock assembly. 2. Remove the access plate at the rear of the front lock assembly. (top two standoff screws) 3. Locate the reset push button at the lower right corner of the circuit board. 4. Hold the button down and wake up the unit by briefly depressing the handle. The unit will beep 3 times. 5.