Instruction Manual

ManualsBrandsPaxton ManualsFor HomeEasyprox nano

Page 1

18/04/2013

Parts list

Tools List

Power Drill

Drill bits 10 mm, 25 mm

Philips screwdriver

Hacksaw for cutting bolts

Hammer / Mallet

Chisel 25 mm

Stanley knife

Adhesive tape

Pencil

Tape measure

8 mm spanner (supplied)

2 mm Allen key (supplied)

1) Front Lock Assembly

2) Rear Lock Assembly

3) Rubber Escutcheon x2

4) Left and Right Handles

5) Battery Pack

6) Tubular Mortice Lock

7) Spindle

8) 8 mm Conversion Sleeve

9) 2 mm Allen Key

10) 8 mm Spanner

11) Strike Plate Backbox

12) Strike Plate

13) Long Mounting Screws x4

14) Short Mounting Screws x4

This unit is for indoor use only.

Technical Support

Technical help is available: Monday - Friday from 07:00 - 19:00 (GMT)

Saturday from 09:00 - 13:00 (GMT)

01273 811011 support@paxton.co.uk

Ins-30107 Easyprox nano

Documentation on all Paxton products can be found on our website - http://www.paxton.co.uk/

This wireless unit requires a Net2Air bridge to

communicate with the server PC.

6 7

8 9

10 11 12

Paxton

This unit requires Net2 v4.23 or later software.

Call Technical Support if you require advice.

Summary of content (8 pages)

PAGE 1
8/04/2013 Paxton Ins-30107 Easyprox nano Technical Support 01273 811011 support@paxton.co.uk Technical help is available: Monday - Friday from 07:00 - 19:00 (GMT) Saturday from 09:00 - 13:00 (GMT) Documentation on all Paxton products can be found on our website - http://www.paxton.co.uk/ This wireless unit requires a Net2Air bridge to communicate with the server PC. This unit is for indoor use only. This unit requires Net2 v4.23 or later software. Call Technical Support if you require advice.
PAGE 2
Installing the hardware Step 1 - Marking out Decide on the lock height and mark this on the door. Fold the template along one dotted line and tape it to the door with the 'Centreline of Latch' at the required height. Mark the 4 x 10 mm and 1 x 25 mm holes. Remove the template, fold along the other dotted line and apply it to the other side of the door at the same height. Mark the holes as before. Step 2 - Drilling 80 25 57 Drill a 25 mm hole in the door edge at least 80 mm deep to accept the latch.
PAGE 3
Step 5 - Mounting on the door Select the short (doors thinner than 45 mm) or long mounting screws and cut to length if required. (door thickness + 5 mm) Fit the rubber escutcheons to the front and back plates. Present the front and rear lock assembly to the door, locating the square drive in its recess and join the two parts together with 4 mounting screws. Step 6 - Fitting the handles Fit the two handles, positioning the screw holes to the underside and secure with the grub screws provided.
PAGE 4
Software installation The Net2 software should be loaded on the controlling PC and at least one Net2Air bridge configured to communicate with the unit. Full documentation is supplied with the Net2Air bridge unit and also on the website as follows: XAN1051 - Installing Net2 software < http://paxton.info/1520 > XIns-30084 - Net2Air USB bridge < http://paxton.info/926 > XIns-30085 - Net2Air Ethernet bridge < http://paxton.info/920 > Download the latest version of Net2 software at: http://paxton.
PAGE 5
Software Configuration Door name: Name the Door. Door open time: Set the door open time. Unlock the Door during: Holds the door unlocked during this timezone. - Set to 'At No Time' for normal user operation. Reader: Local settings for the reader. Output: Configures the lock for timed release or toggle mode. Events: Shows the events for this control unit only. Access Rights: Lists users who have access through this door. Name: The reader can be named individually if required.
PAGE 6
Commissioning checks With the product fixed securely to the door: 1) Extend the door open time by changing this door's settings on the Net2 PC. Set ' Door open time' to 20 seconds and then present a user card at the door. Before each check, present a user card to unlock the door.
PAGE 7
Low battery warning When the battery voltage falls below 4V, the user will see a delay between the card being read and access being granted. This delay provides a warning that the battery pack should be replaced. The warning delay starts at 2 seconds, increasing up to 10 seconds as the battery discharges with use. Battery replacement 1. 2. 3. 4. Remove the unit from the door by removing the 4 securing screws on the rear lock assembly. Remove the top two standoff screws - Fig 1.
PAGE 8
Specifications Features Min Number of Cards Access levels 250 Time zones Maximum door open time Max 10,000 64 1 sec 60 sec 10 ACU's per Net2Air bridge - Recommended 200 Net2Air bridge per system Net2Air wireless range 20 m Events stored in ACU with no server connection 3,584 Read Range Environment Operating temperature - Battery limits Token Keyfob 50 mm 30 mm Min Max 0 °C + 55 °C Waterproof No Vandal resistance Low Paxton Battery Pack Battery type - High capacity (746-003) 6V DC