Specifications

ManualsBrandsPaxton Manualscomputer componentsNet2 RS485 TCP/IP Ethernet

Page 1

0V12V

Green

White/Green

Screen or spare cores from

network cable

White/O rang e

Orang e

KR 1redae dap

e 1

R le ay 2

R le ay 1

Keypad 2 Reader 2

stupnI

P ewo r

nidocelbac5T g

krowteN

Net2 classic

Red 12V dc

Red LED

Amber LED

Green LED

Data/D0

Clock/D1

Media Detect

0V out

Load

Data

Clock

R c

dV21de

R DELde

DELrebm

DELnee

/ataD

1D/kcolC

tceteDa

ideM

tuo

daoL

ataD

kcolC

+12V

:noit

uaC

o ylnosre

erc

dV2

. F tcerrocro

noitcennoc fo f

rsredaerV

5dlo re ot

sno

itcurt

sni

PLACE SERIAL

NUMBER

LABEL HERE

http://paxton.info/107

123456

0889

Reset to DHCP

mode

Unswitched

fused spur

To next ACU

The interface plugs directly

into the TCP/IP Ethernet

network via a standard

RJ45 connection box.

Switchable 120 ohm

resistors

To reset the unit to DHCP, power up with

the reset button held down until the unit

beeps. The interface is now fully reset

and will now operate in DHCP mode.

Ins-30001 Net2 485 TCP/IP Ethernet interface (Rev4)

Fitting

29/06/2011

Suitability

**IMPORTANT - THIS IS A NETWORK DEVICE**

Please contact your IT Administrator before installing this product

DHCP compatible

(xed IP recommended)

Connect over LAN, WAN or VPN

Technical Support

Technical help is available: Monday - Friday from 07:00 - 19:00 (GMT)

Saturday from 09:00 - 13:00 (GMT)

01273 811011 support@paxton.co.uk

Documentation on all Paxton products can be found on our website - http://www.paxton.co.uk/

**IMPORTANT**

Apply power to the unit after connecting

the RJ45 plug to a network point.

This device requires Net2 v4.07 or later to operate.

Earlier Net2 software is not compatible with this unit.

If your PC can only support Net2 v3 software, please

contact Technical Support for further advice.

1. Power (Green) - 12V power LED.

2. Termination (Red) - The on-board resistors are in place across the RS485 data pairs.

3. Rx (Red) - The interface is receiving data (RS485).

4. Tx (Green) - The interface is sending data (RS485).

5. Server Connected (Green) - The TCP/IP interface is communicating with the PC Net2 server.

6. Server Link Green = 100 Mbit/s : Orange = 10 Mbit/s (TCP/IP speed).

LED indications

Paxton

Summary of content (4 pages)

PAGE 1
29/06/2011 Paxton Ins-30001 Net2 485 TCP/IP Ethernet interface (Rev4) Technical Support 01273 811011 support@paxton.co.uk Technical help is available: Monday - Friday from 07:00 - 19:00 (GMT) Saturday from 09:00 - 13:00 (GMT) Documentation on all Paxton products can be found on our website - http://www.paxton.co.
PAGE 2
The Net2 TCP/IP Ethernet Interface allows a Net2 data line to be controlled from a PC running the Net2 Server across a TCP/IP Ethernet network. There is a 1 km maximum length for a data line. This can be increased by using Net2 RS485 high speed repeaters (477-836) or by creating multiple data lines using several Ethernet connections controlled from the one PC. The data line must be wired in a single daisy chain. The data converter may be located anywhere along the data line.
PAGE 3
When connecting to a LAN The IP address should be assigned a fixed value, or should be given a DHCP reservation. Unreserved IP addresses issued by DHCP servers are not guaranteed to be constant, leading to potential failure of communication between Net2 software and the device. Run the Net2 Server Configuration Utility (Start/Programs/Net2) and Click on TCP/IP nodes. Click on;Detect and the MAC address of the device(s) will appear in the table.
PAGE 4
If you detect the MAC address but the device now shows 'Not Responding', you must check the IP address, to make sure it is still in range with the PC or network. If it is not, you should either change the IP address of the PC or the IP address of the device so they are both again in the same range. Our Technical team can talk you through this if you need help.