This publication, photographs, illustrations and software are under the protection of international copyright laws and all rights reserved. It does not allow any reproduction of this manual, content and any materials contained herein without the written consent of the authentic manufacturer. The information in this manual is subject to change without notice.
Table of Contents Trademark ..................................................................................... I Static Electricity Precautions.................................................III Pre-Installation Inspection.....................................................III Features & Checklist Translations.............................................. V Chapter 1: Introduction.................................................................1 Key Features ...........................................
Static Electricity Precautions Static electricity could damage components on this mainboard. Take the following precautions while unpacking this mainboard and installing it in a system. 1. Don’t take this mainboard and components out of their original static-proof package until you are ready to install them. 2. While installing, please wear a grounded wrist strap if possible. If you don’t have a wrist strap, discharge static electricity by touching the bare metal of the system chassis. 3.
Notice: 1.Owing to Microsoft’s certifying schedule is various to every supplier, we might have some drivers not certified yet by Microsoft. Therefore, it might happen under Windows XP that a dialogue box (shown as below) pop out warning you this software has not passed Windows Logo testing to verify its compatibility with Windows XP. Please rest assured that our RD department has already tested and verified these drivers. Click the “Continue Anyway” button and go ahead the installation. 2. USB 2.
Features & Checklist Translations Liste de contrôle Le coffret de votre carte mère contient les éléments suivants : La carte mère Le Manuel utilisateur Un câble plat pour lecteur de disquette (optionnel) Une câble plat pour lecteur IDE CD de support de logiciels Features Processeur Prise en charge du Processeur Socket-478 • Supporte le CPU Intel Pentium 4 series avec la Technologie Hyper Threading ● Supporte un Bus Avant allant jusqu’à 800 MHz La technologie “Hyper-Threading” permet au système d’exploitat
IDE Interne Ports E/S Internes LAN Fast Ethernet (optionnel) USB 2.0 • Deux Connecteurs IDE • Prend en Charge les modes PIO (Entrée/Sortie Programmable) et DMA (Accès Direct à la Mémoire) • Supporte maîtrise de bus Ultra DMA IDE avec vitesse de transfert de 33/66/100/133 Mo/sec La carte mère possède un jeu complet de ports d’E/S et de connecteurs: •Deux ports PS/2 pour souris et clavier •Un port série •Un port parallèle •Six ports USB2.
Checkliste Die Verpackung Ihres Mainboards enthält folgende Teile: Mainboard Handbuch Bandkabel für Floppylaufwerke (optional) Bandkabel für IDE-Laufwerke Software-CD Ausstattung Prozessor Unt Unterstütz Socket-478-Prozessoren • Unterstützung für Intel Pentium 4-CPUs mit “Hyper-Threading”Technologie • Unterstützung von bis zu 800 MHz Front-Side Bus “Hyper-Threading”-Technologie läßt das Betriebssystem glauben, es sei an zwei Prozessoren angeschlossen, was zwei parallele Threads auf separaten ‘logischen’
Onboard I/O Ports Fast Ethernet LAN (optional) USB 2.0 Das Mainboard verfügt über einen kompletten Satz von I/O-Schnittstellen und Anschlüssen: • Zwei PS/2-Steckplätze für Maus und Tastatur yboard • Ein serieller Steckplatz • Ein paralleler Steckplatz • Sechs USB2.0-Ports (vier auf der Rückseite, Onboard USB-Header für zwei zusätzliche Ports) • Audioanschlüsse für Mikrofon, line-in und line-out •Unterstützt 10/100Mbps-Betrieb und halben/vollen Duplex-Betrieb •Übereinstimmend mit IEEE 802.3/802.
Lista L’imballo della scheda madre é composto da: La scheda madre Il manuale Una piattina per il collegamento dei drive (opzionale) Una piattina IDE Il CD con il Software di supporto Features Processor Dotata di Socket 478 per Processori • Supporta CPU Intel Pentium serie 4 con tecnologia Hyper Threading • Supporta fino a 800 MHz Front Side Bus La tecnologia Hyper-Threading permette al sistema operative di essere dotato di due procressori.
Onboard LAN (opzionale) USB 2.0 • Sei porte USB2.0 (quattro porte sul pannello posteriore, terminali USB a bordo che offrono due porte extra) • Jack audio per microfono, ingresso linea e uscita linea • Operazioni 10/100Mbps e half/full duplex • Conforme allo standard IEEE 802.3/802.3u • Negoziazione automatica 28 clause IEEE 802.
LiSTA DE VERIFICACIÓN El paquete de su placa principal contiene los sigtes.
Puertos I/O Abordos Ethernet LAN Rápido (optional) USB 2.0 La placa principal tiene un juego completo de puertos I/O y conectores: • Dos puertos PS/2 para ratón y teclado • Un puerto serial • Un puerto paralelo • Seis puertos USB 2.0 (cuatro puertos de panel trasero, cabezales USB abordos que proveen dos puertos extras) • Clavijas de sonido para micrófono, entrada y salida de línea • Soporta operación 10/100Mbps y operación de duplex medio/completo. • Conformidad IEEE 802.3/802.
Lista de verificação A embalagem da sua placa principal contém os seguintes itens: A placa principal O Manual do Utilizador Um cabo para a unidade de disquetes (opcional) Um cabo para a unidade IDE CD de suporte para o software Características Processador Suporte do Processador Socket-478 • Suporta CPU série Intel Pentium 4 com Tecnologia Hyper Threading • Suporta até 800 MHz Front-Side Bus Tecnologia Hyper-Threading que permite o sistema operador a pensar que ele está conectado em dois processadores, faz
Fast Ethernet LAN (optional) USB 2.0 • Uma porta série • Uma porta paralela • Seis portes USB2.0 (quatro portes traseiros, um conector USB na placa com dois portes extras) • Jacks audio para microfone, line-in e line-out • Suporta operação 10/100Mbps e operação parcial/completa duplex IEEE 802.3/802.3u complacente • Suporta IEEE 802.
检查单 您的主板包装含有以下项目： 主板 用户手册 一根磁盘驱动器扁平电缆（可选） 一根 IDE 驱动器扁平电缆 软件支持 CD 功能 处理器 支持 Socket-478 处理器 • 支持带有/多线程技术的 Intel Pentium 4 系列 CPU • 支持 800 MHz 前端总线 “多线程”技术可以让操作系统认为自己连接了两个处理器，允许两个 线程并行运行，每个线程位于同一处理器中的单独“逻辑”处理器中。 芯片组 芯片组包含 868Pro HT1683/HT1563, 它基于一种新型的、可扩展的架构，能 提供已经证明的可靠性和高性能。 • 2x 寻址和 4x 数据传输。 • 64 位数据总线和 32 位寻址。 • 266/333/400MHz DDR SDRAM 内存 • 支持 AGP 规格 V2.0、V3.0。 • 支持 HyperTransportTM I/O，带宽可达 1.6GB/s。 • 符合 PCI 2.
Onboard LAN (optional) USB 2.0 • 6 个 USB 2.0 端口（主板后面板带 4 个接口，板上 USB 接口提供其它 2 个 端口） • 麦克风、线入和线出声音插孔 • 支持 10/100Mbps 工作和半/全双工工作 • 符合 IEEE 802.3/802.3u 标准 • 支持 IEEE 802.3u 第 28 项的自协商 • 支持链路故障节电模式下操作 • 支持基线漂移 (BLW) 补偿 • 自适应均衡 • 符合通用串行总线规格 2.0 版本 • 符合 Intel 0.95 版本的增强主控器接口规格 • 符合 1.1 版本的通用主控器接口规格 • PCI 多功能设备由 2 个用于全速/低速传输数据的 UHCI 主控器 和 1 个用于 高速传输数据的 EHCI 主控器组成 • Root 集线器包括 4 个下行端口，带有与 UHCI 和 EHCI 主控制器共用的集 成物理层收发器。 • 支持 1.
Chapter 1 Introduction This mainboard has a Socket-478 supporting Intel Pentium 4/Hyper Threading Technology processors with Front-Side Bus (FSB) speeds up to 800 MHz. Hyper Threading Technology, designed to take advantage of the multitasking features in Windows XP, gives you the power to do more things at once. This mainboard integrates the 868Pro HT1683/HT1563 chipsets that support the built-in USB 2.0 providing higher bandwidth, implementing Universal Serial Bus Specification Revision 2.
Key Features This mainboard has these key features: Socket-478 Processor ♦ Supports Intel Pentium 4 series CPU with Hyper Threading Technology ♦ Supports up to 800 MHz Front-Side Bus Hyper-Threading technology enables the operating system into thinking it’s hooked up to two processors, allowing two threads to be run in parallel, both on separate ‘logical’ processors within the same physical processor.
♦ Full-duplex Codec with independent and variable sampling rate ♦ Earphone Buffer Built-In, SNR up to 90db ♦ 4Ch DAC, support 4-channel speak-out ♦ Advanced power management support Expansion Options The mainboard comes with the following expansion options: ♦ Four 32-bit PCI slots ♦ One 8x AGP slot ♦ One Communications Network Riser (CNR) slot Onboard IDE ♦ Two IDE Connectors ♦ Supports PIO (Programmable Input/Output) and DMA (Direct Memory Access) modes ♦ Supports IDE Ultra DMA bus mastering with transfer
USB 2.0 ♦ Compliant with Universal Serial Bus Specification Revision 2.0 ♦ Compliant with Intel’s Enhanced Host Controller Interface Specification Revision 0.95 ♦ Compliant with Universal Host Controller Interface Specification Revision 1.
Package Contents Your mainboard package contains the following items: The mainboard The User’s Manual One diskette drive ribbon cable (optional) One IDE drive ribbon cable The Software support CD Optional Accessories You can purchase the following optional accessories for this mainboard. The Extended USB module The CNR v.
Chapter 2 Mainboard Installation To install this mainboard in a system, please follow these instructions in this chapter: Identify the mainboard components Install a CPU Install one or more system memory modules Make sure all jumpers and switches are set correctly Install this mainboard in a system chassis (case) Connect any extension brackets or cables to connectors on the mainboard Install peripheral devices and make the appropriate connections to connectors on the mainboard Note: 1.
Mainboard Components Identify major components on the mainboard via this diagram underneath. Note: Any jumpers on your mainboard that do not appear in this illustration are for testing only. I/O Ports The illustration below shows a side view of the built-in I/O ports on the mainboard.
PS/2 Mouse PS/2 Keyboard Parallel Port (PRN) COM1 LAN Port (optional) USB Ports Use the upper PS/2 port to connect a PS/2 pointing device. Use the lower PS/2 port to connect a PS/2 keyboard. Use the Parallel port to connect printers or other parallel communications devices. Use the COM port to connect serial devices such as mice or fax/modems. COM1 is identified by the system as COM1. Connect an RJ-45 jack to the LAN port to connect your computer to the Network. Use the USB ports to connect USB devices.
2. Match the pin1 corner marked as the beveled edge on the CPU with the pin1 corner on the socket. Insert the CPU into the socket. Do not use force. 3. Push the locking lever down and hook it under the latch on the edge of socket. 4. Apply thermal grease to the top of the CPU. 5. Install the cooling fan/heatsink unit onto the CPU, and secure them all onto the socket base. 6. Plug the CPU fan power cable into the CPU fan connector (CPUFAN1) on the mainboard.
Memory Module Installation Procedure These modules can be installed with up to 2 GB system memory. Refer to the following to install the memory module. 1. Push down the latches on both sides of the DIMM socket. 2. Align the memory module with the socket. There is a notch on the DIMM socket that you can install the DIMM module in the correct direction. Match the cutout on the DIMM module with the notch on the DIMM socket. 3.
Install the Mainboard Install the mainboard in a system chassis (case). The board is an ATX size mainboard. You can install this mainboard in an ATX case. Make sure your case has an I/O cover plate matching the ports on this mainboard. Install the mainboard in a case. Follow the case manufacturer’s instructions to use the hardware and internal mounting points on the chassis. PJ1 SYSFAN1 1 1 1 ATX1 SW1 Connect the power connector from the power supply to the ATX1 connector on the mainboard.
Connecting Optional Devices Refer to the following for information on connecting the mainboard’s optional devices: IR1 1 1 JP1 1 1 AUDIO1 USB3 1 SPK1 SPK1: Speaker Connector Connect the cable from the PC speaker to the SPK1 header on the mainboard. Pin 1 3 Signal SPKR GND Pin 2 4 Signal NC +5V AUDIO1: Front Panel Audio Connector This connector allows the user to install auxiliary front-oriented microphone and line-out ports for easier access.
Pin 1 3 5 7 9 Signal VERG_FP_USBPWR0 USB_FP_P0USB_FP_P0+ GROUND KEY Pin 2 4 6 8 10 Signal VERG_FP_USBPWR0 USB_FP_P1USB_FP_P1+ GROUND USB_FP_OC0 1. Locate the USB3 connector on the mainboard. 2. Plug the bracket cable onto the USB3 connector. 3. Remove a slot cover from one of the expansion slots on the system chassis. Install an extension bracket in the opening. Secure the extension bracket to the chassis with a screw.
IR1: Infrared Port The infrared port allows the wireless exchange of information between your computer and similarly equipped devices such as printers, laptops, Personal Digital Assistants (PDAs), and other computers. Pin 1 3 5 Signal NC +5V IRTX Pin 2 4 6 Signal KEY GND IRRX 1. Locate the infrared port IR1 connector on the mainboard. 2. If you are adding an infrared port, connect the ribbon cable from the port to the IR1 connector and then secure the port to an appropriate place in your system chassis.
IDE Devices IDE devices include hard disk drives, high-density diskette drives, and CD-ROM or DVD-ROM drives, among others. The mainboard ships with an IDE cable that can support one or two IDE devices. If you connect two devices to a single cable, you must configure one of the drives as Master and one of the drives as Slave. The documentation of the IDE device will tell you how to configure the device as a Master or Slave device. The Master device connects to the end of the cable.
Expansion Slots This mainboard has one AGP, one CNR and four 32-bit PCI slots. AGP1 CNR1 PCI4 PCI3 PCI2 PCI1 Follow the steps below to install an AGP/CNR/PCI expansion card. 1. Locate the AGP, CNR or PCI slots on the mainboard. 2. Remove the blanking plate of the slot from the system chassis. 3. Install the edge connector of the expansion card into the slot. Ensure the edge connector is correctly seated in the slot. 4. Secure the metal bracket of the card to the system chassis with a screw.
Chapter 3 BIOS Setup Utility Introduction The BIOS Setup Utility records settings and information of your computer, such as date and time, the type of hardware installed, and various configuration settings. Your computer applies the information to initialize all the components when booting up and basic functions of coordination between system components. If the Setup Utility configuration is incorrect, it may cause the system to malfunction. It can even stop your computer booting properly.
Running the Setup Utility Every time you start your computer, a message appears on the screen before the operating system loading that prompts you to “Hit if you want to run SETUP”. Whenever you see this message, press the Delete key, and the Main menu page of the Setup Utility appears on your monitor. CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc.
Standard CMOS Setup Page This page displays a table of items defining basic information about your system. CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc. Standard CMOS Setup System Time: System Date: Primary IDE Master : Primary IDE Slave : Secondary IDE Master : Secondary IDE Slave : 14:24:16 Thu 10/09/2003 Hard disk Not Detected Not Detected CD/DVD ROM Help Item User [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. Floppy Drive A : 1.
Advanced Setup Page This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer. CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc.
Graphic Win Size DRAM CAS Latency Hyper Threading Function Auto detect DIMM/PCI Clock Spread Spectrum This item defines the size of aperture if you use a graphic adapter. This item determines the operation of SDRAM memory CAS (column address strobe). It is recommended that you leave this item at the default value. The 2T setting requires faster memory that specifically supports this mode. If your P4 CPU is not HT CPU, this item will be hidden. If your P4 CPU is HT CPU, BIOS will show this item.
Features Setup Page This page sets up some parameters for peripheral devices connected to the system. CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc.
Controller Audio Device Modem Device Ethernet Device OnBoard USB Function USB Function For DOS IDE channels. This item enables or disables the AC’97 audio chip. This item enables or disables the AC’97 modem chip. This item enables or disables the onboard Ethernet LAN. Enable this item if you plan to use the USB ports on this mainboard. Enable this item if you plan to use the USB ports on this mainboard in a DOS environment.
Power Management Suspend Time Out Resume On RTC Alarm Keyboard Power On LAN/Ring Power On Use this item to enable or disable a power management scheme. If you enable power management, you can use the items below to set the power management operation. Both APM and ACPI are supported. This item sets up the timeout for Suspend mode in minutes. If the time selected passes without any system activity, the computer will enter power-saving Suspend mode. The system can be turned off with a software command.
PCI / Plug and Play Setup Page This page sets up some parameters for devices installed on the PCI bus and those utilizing the system plug and play capability. CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc. PCI / Plug and Play Setup Primary Graphics Adapter Allocate IRQ to PCI VGA PCI IDE BusMaster Primary Graphics Adapter Allocate IRQ to PCI VGA PCI IDE BusMaster AGP Yes Disabled Help Item Select which graphics controller to use as the primary boot device.
BIOS Security Features Setup Page This page helps you install or change a password. CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc. BIOS Security Features Setup Security Settings Help Item Supervisor Password : Not Installed Change Supervisor Password Press Enter Supervisor Password Change Supervisor Password Install or Change the password. This item indicates whether a supervisor password has been set. If the password has been installed, Installed displays.
CPU PnP Setup Page This page helps you manually configure the CPU of this mainboard. The system will automatically detect the type of installed CPU and make the appropriate adjustments to these items on this page. CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc.
Hardware Monitor Page This page sets up some parameters for the hardware monitoring function of this mainboard. CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc. Hardware Monitor Setup *** System Hardware Monitor*** Vcore Vdimm Vivdd Vcc5V SB3V CPU Fan Speed SYSTEM Fan Speed CPU Temperature SYSTEM Temperature CPU/NB/System Temperature FAN & Voltage Measurements 1.419V 2.544V 2.112V 5.026V 3.
Discard Changes and Exit Highlight this item and press to discard any changes that you have made in the Setup Utility and exit the Setup Utility. When the Discard Changes and Exit dialog box appears, press to discard changes and exit, or press to return to the main menu. Note: If you have made settings that you do not want to save, use the "Discard Changes and Exit" item and press to discard any changes you have made.
Chapter 4 Software & Applications Introduction This chapter describes the contents of the support CD-ROM that comes with the mainboard package. The support CD-ROM contains all useful software, necessary drivers and utility programs to properly run our products. More program information is available in a README file, located in the same directory as the software. To run the support CD, simply insert the CD into your CD-ROM drive.
Installing Support Software 1.Insert the support CD-ROM disc in the CD-ROM drive. 2.When you insert the CD-ROM disc in the system CD-ROM drive, the CD automatically displays an Auto Setup screen. 3.The screen displays three buttons of Setup, Browse CD and Exit on the right side, and three others Setup, Application and ReadMe at the bottom. Please see the following illustration. The Setup button runs the software auto-installing program as explained in next section.
Auto-Installing under Windows 98/ME/2000/XP If you are under Windows 98/ME/2000/XP, please click the Setup button to run the software auto-installing program while the Auto Setup screen pops out after inserting the support CD-ROM: 1. The installation program loads and displays the following screen. Click the Next button. 2. Select the items that you want to setup by clicking on it (the default options are recommended). Click the Next button to proceed. 3. The support software will automatically install.
Installing under Windows NT or Manual Installation If you are under Windows NT, the auto-installing program doesn’t work out; or you have to do the manual installation, please follow this procedure while the Auto Setup screen pops out after inserting the support CD-ROM: 1. Click the ReadMe to bring up a screen, and then click the Install Path at the bottom of the screen. 2. Find out your mainboard model name and click on it to obtain its correct driver directory. 3.
Hyper Threading CPU You must update BIOS to initiate BIOS Hyper Threading Function and use HT CPU function under WinXP Operating System; if not, please disable this option. ♦ When BIOS detects the HT CPU, it shows the “Hyper Threading Function (default Disabled)” option, which you must set Enabled if you want to test HT CPU function. If there is no HT CPU, this option is hidden and default Disabled. ♦ You must re-install WINXP to activate the HT CPU function.
