Integration Guide
Table Of Contents
- Cover
- Table of Contents
- Tables and Figures
- Text Format Conventions
- Terms and Abbreviations
- Referenced Documents
- 1. Overview
- 2. Architecture
- 3. Connectors
- 4. Software Integration
- 5. Mechanical
- 6. Compliance
- 6.1. Manufacturer’s Federal Communication Commission (FCC) Compliance Statements
- 6.1.1. Antenna Information
- 6.1.2. FCC Declaration of Conformity Statement
- 6.1.3. FCC Radiation Exposure Statement
- 6.1.4. Factors Affecting Module Usage Related to FCC Compliance
- 6.2. Manufacturer’s Innovation, Science and Economic Development (ISED) Canada Compliance Statements
- 6.2.1. Antenna Information
- 6.2.2. ISED (Canada) Compliance Statement
- 6.2.3. ISED Canada Radiation Exposure Statement
- 6.2.4. Factors Affecting Module Usage Related to ISED Compliance
- 6.2.4. Limites d'utilisation du module liées à la conformité ISED
- 6.3. Manufacturer’s European Union (EU) and United Kingdom (UK) Compliance Statements
- 6.3.1. EU and UK Declaration of Conformity
- 6.3.2. Antenna Information
- 6.3.3. European Union and UK Radiation Exposure Statement
- 6.3.4. EU and UK Compliance Statement
- 7. Safety Notices
- Industrial IoT Product Usage
20
INTEGRATION GUIDE
6.2.2. ISED (Canada) Compliance Statement
The following paragraphs must be included in any end-user documentation.
This device contains license-exempt transmitters/receivers that comply with
Innovation, Science and Economic Development Canada’s license-exempt RSSs.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement Économic Canada
applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage.
2. L’appareil doit accepter tour brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
6.2.3. ISED Canada Radiation Exposure Statement
These paragraphs must be included in any end-user documentation.
This transmitter/receiver has been evaluated for RF exposure for humans in
reference to ANSI C 95.1 (American National Standards Institute) limits. This
evaluation was based on RSS-102 Rev 5. To maintain compliance, the minimum
separation distance for RM-WIFI-AC-2X2-HP-CA is 7.87 inches (20 cm) from users
or general bystanders. Further RF exposure reduction can be achieved if the
product/antennas are kept as far as possible from the user’s body or is set to a
lower RF output power if such a function is available.
Cet émetteur/récepteur a été évalué quant à l'exposition aux RF pour les
personnes en référence aux limites ANSI C 95.1 (American National Standards
Institute). Cette évaluation est basée sur la norme RSS-102 Rév 5. Pour maintenir
la conformité, la distance minimale de séparation pour le RM-WIFI-AC-2X2-HP-CA
est de 7,87 pouces (20 cm) par rapport aux personnes présentes. Une réduction
supplémentaire de l'exposition aux RF peut être obtenue si le produit/les antennes
sont maintenus aussi loin que possible du corps de l'utilisateur ou s'ils sont réglés
sur une puissance de sortie RF inférieure, si une telle fonction est disponible.
6.2.4. Factors Aecting Module Usage Related to ISED Compliance
The RM-WIFI-AC-2X2-HP-CA radio module has been certied by the ISED under
the rules for a Modular Transmitter. There are some considerations and limitations
that are important for the end user or integrator of the module: