Live Air 2 PDMOVIE Wireless Follow Focus System
Wecome To Use LIVE AIR 2 Notice For Use Before using the product, please read the instructions carefully or watch the tutorial videos to learn how to use the products properly. If there are any direct or indirect adverse effects due to operational errors, PDMOVIE will not assume any responsibility. Please do not dismantle, repair or refit the internal structure of the product without authorization.
Configuration List ① ② ③ ④ Controller （PDL-TC-AFP） Controller （PDL-TC-AZ） Controller （PD2-HT） MOTOR MINI （PD-BTMP） ⑤ ⑥ ⑦ ⑧ Li42B Battery Li42Bx2 Battery Micro USB Charging Cable Li42B Battery Charger ⑨ ⑩ 11 Camera Hot Shoe Clamp 15MM Pipe USB Charging Cable 0.9m ( 4 pin ) Serial number Name PDL-AFP PDL-AZP PDL-AP 1 Controller（PDL-TC-AFP） 1 － － 2 Controller（PDL-TC-AZ） － 1 － 3 Controller（PD2-HT） － － 1 4 MOTOR MINI（PD-BTMP） 1 1 1 5 Li42B Battery (3.7V 600mAh 2.
PDL-AFP/AZP Instruction Manual Antenna Micro USB 0.8 Gear Charge Interface Lights For Controller Status Focus Control ON/OFF Button CALIBRATION/ RESET Button Lights For Motor Status U-clamp Wheel Battery 1. Install Motor Install the motor on the 15mm rod and make sure the motor gear matches with the lens gear.( If it install on DSLR Camera lens, please use the camera hot shoe clamp.) Step 1. Install the motor on 15mm rod. Step 3. Install battery. Step 2. Locking U-clamp.
2. Turn on the Bluetooth controller and motor Press the ON/OFF button on the Bluetooth controller for three seconds until the indicator light powers on. The motor will turn on automatically when the battery is inserted. 3. Bluetooth Connection After the Bluetooth controller is turned on, the indicator lights will flash quickly for 60 seconds, which means the Bluetooth is searching. When the Bluetooth connection is successful, the controller indicator light will brighten all the time.
(3) Manually calibration: A. When the motor gear and the lens gear are completely connected,turn the lens to the starting point and hold for 0.5 seconds. B. Then turn the lens ring to the end and hold for 0.5 seconds. C. Finally turn the lens ring back towards the center to finish. (It is recommend that you use manual calibration when using a DSLR camera lens) (1) Turn the lens ring to the starting point and hold for 0.5 seconds. (2) Turn the lens ring to the end and hold for 0.
Table 2 Bluetooth controller.
REMOTE AIR APP The motor can also be controled by the iOS app. Please search PDMOVIE or REMOTE AIR, then download the app from the Apple store. 1.Turn on the motor.* 2.Initiate Bluetooth on phone. 3. Turn on the APP (Automatically connects to the motor)* 1. Please make sure the Bluetooth controller is off. 2. Before opening the app, please make sure the app is not already running, if so, please close the app and reopen again.
Bluetooth Control PDL-AP Instruction Manual Start pairing 1. Controller turns on Bluetooth mode： Please make sure the handle is turned off, and then press the ON/OFF button and the FOCUS button in the meantime.Short press three times, then press and hold the ON/OFF button to refresh the bluetooth. 2. Insert the battery to start the motor. 3.
Supplementary Specification 1. App introduction information or video obtained by PDMOVIE official website/ FACEBOOK/ YOUTUBE. Or find it from APP interface - “SET” “HELP” . 2. The normal run time of Bluetooth controller PDL-TC-AF is 8-10 hours. If the controller battery runs out , it can use the USB 5V output or other mobile power for charging. The normal charge time is 20-25 minutes. 3. The distance for Bluetooth control is 32 feet, and Bluetooth controller (PDL-TC-AF) is mainly used for a single user. 4.
