Owner's manual

ManualsBrandsPDR Mounts ManualsAccessories for videoawm125-vesa

Model

AWM125 ARTICULATING WALL MOUNT INSTRUCTIONS

Thank you for purchasing the PDR mount.

To ensure the correct usage, please read and follow the instructions

manual thoroughly. Please store the instructions in a safe place

To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the weight

display and the wall mount.

Always use at least two persons for all installations.

Fully tighten all of the mounting screws as specified in the installation instructions.

Features

Special techniques are necessary for installation of the panel display mount.

Do not attempt to perform this work by yourself.

Request an installation specialist to install this unit.

Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.

Please remember that if you remove the panel display from the wall later, you will find the screw holes and anchor bolts for t

mounting unit left on the wall. Also note that long use of the panel display may discolor the wall around it due to its heat a

airflow.

Fig 1

All PDR mounts and adapters carry a lifetime warranty against defects in material and workmanship. We are not liable for

improper installation that results in damage to mounts, adapters or presentation equipment.

Visit our web site @ www.pdrmounts.com

Mounts by

A division of David Engineering & Mfg. Inc.

for future reference.

of both the panel

Simple to adjust

Adapter plate included

125 lb rated ( 22” to 36” max TV recommended )

Rugged heavy gauge metal construction

Tough powder-coated finish

Extends 19.85” from the wall and closes to under 4”

Pivots left or right, tilts up 5 deg and down 15 deg

Includes cable management system

Tension bolts to adjust smooth action and eliminate creep

Summary of content (6 pages)

PAGE 1
Mounts by A division of David Engineering & Mfg. Inc. Model AWM125 ARTICULATING WALL MOUNT INSTRUCTIONS Thank you for purchasing the PDR mount. To ensure the correct usage, please read and follow the instructions manual thoroughly. Please store the instructions in a safe place for future reference. All PDR mounts and adapters carry a lifetime warranty against defects in material and workmanship.
PAGE 2
INSTALLATION LOCATION WARNING The wall where the wall mount is to be installed must be capable of long-term support of the total load of the panel display and wall mount. Measures should al so be taken to ensure sufficient strength to withstand the force of earthquakes, vibration and other external forces. Note: Incorrect installation can cause the panel display to fall and cause injury. Total load ( panel display + mount ) MAXIMUM WEIGHT= 125 Lbs. ( 57 Kg.
PAGE 3
PARTS LIST 1 6 M6-1.0 X 16 PAN HEAD PHILLIPS MACHINE SCREW 4 REQUIRED 5/16 X 2 1/2 LAG BOLT 3 REQUIRED 2 7 1/4-20 X 1/2" SELF TAPPING PAN HEAD SCREW 4 REQUIRED 5/16 X 7/8 USS STEEL FLAT WASHER 3 REQUIRED 8 3 1/4 X 1/2 X 3/16 PLASTIC SPACER 4 REQUIRED PLASTIC CABLE MANAGEMENT CABLE TIE HOLDER 4 REQUIRED 9 4 M4-0.7 X 16 PAN HEAD PHILLIPS MACHINE SCREW 4 REQUIRED NYLON ZIP TIE 4 REQUIRED 5 M5-0.
PAGE 4
Model AWM125 DRAWING SPECIFICATIONS Single stud articulating wall mount 15° 5° 19.85” 15.06 cL 3.84 3.07 14.13 [200] [100] 7.87 3.94 [100] 3.94 [200] 7.
PAGE 5
1. FASTEN MOUNT TO THE WALL Determine the exact mounting location of the wall mount prior to the installation, considering the swing of the articulating arm. The AWM125 mount must be secured to the CENTER of the wall stud capable of at least (4) times the weight of the display and AWM125 mount. The center of the AWM125 should be mounted at the same horizontal center line as the desired display center line (viewing horizontal center line). 1:Position the AWM125 mount to the desired position.
PAGE 6
3. Mounting the display onto the AWM125 Articulating arm 1: With the VESA adapter plate attached to the display, lift and place the slot on top of the VESA adapter plate onto the tab of the AWM125 tilt plate See fig 4 Allow the display to swing down and locate flush with the studs engaging into the slots on the AWM125 mount. See fig 4 2:Using the washers and nuts supplied, fasten the display to the AWM125 articulating arm. See fig 4 and 5 Fig 4 Fig 5 Slot and Tab WASHER AND NUT 3.