Manual

ManualsBrandsPDR Mounts ManualsAccessories for videoawm250

Model

AWM250 ARTICULATING WALL MOUNT INSTRUCTIONS

Thank you for purchasing the PDR mount.

To ensure the correct usage, please read and follow the instructions

manual thoroughly. Please store the instructions in a safe place

To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the weight

display and the wall mount.

Always use at least two persons for all installations.

Fully tighten all of the mounting screws as specified in the installation instructions.

Features

Special techniques are necessary for installation of the panel display mount.

Do not attempt to perform this work by yourself.

Request an installation specialist to install this unit.

Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.

Please remember that if you remove the panel display from the wall later, you will find the screw holes and anchor bolts for t

mounting unit left on the wall. Also note that long use of the panel display may discolor the wall around it due to its heat a

airflow.

Fig 1

All PDR mounts and adapters carry a limited lifetime warranty against defects in material and workmanship. We are not liable

for improper installation that results in damage to mounts, adapters or presentation equipment.

To register visit our web site @ www.pdrmounts.com

Mounts by

A division of David Engineering & Mfg. Inc.

for future reference.

of both the panel

Features:

RSimple to adjust

R250 lb load rating ( 50” to 71” TV max recommended ) adapter may be required for large displays

RRugged heavy gauge metal construction

RTension adjustment on all joints “ANTI-CREEP TENSION ADJUSTMENT”

RTough powder-coated “Matte Black” finish

RExtends 25.1” from wall and closes to 4.7”

RPivots left or right tilts up 5 deg, down 15deg

RCable management included

RLimited lifetime manufacturer warranty on defects in material or workmanship

RMade in the USA

Summary of content (8 pages)

PAGE 1
Mounts by A division of David Engineering & Mfg. Inc. Model AWM250 ARTICULATING WALL MOUNT INSTRUCTIONS Thank you for purchasing the PDR mount. To ensure the correct usage, please read and follow the instructions manual thoroughly. Please store the instructions in a safe place for future reference. All PDR mounts and adapters carry a limited lifetime warranty against defects in material and workmanship.
PAGE 2
INSTALLATION LOCATION WARNING The wall where the wall mount is to be installed must be capable of long-term support of the total load of the panel display and wall mount. Measures should al so be taken to ensure sufficient strength to withstand the force of earthquakes, vibration and other external forces. Note: Incorrect installation can cause the panel display to fall and cause injury. Total load ( panel display + mount ) MAXIMUM WEIGHT - 250 Lbs. ( 113 Kg.
PAGE 3
DRAWING SPECIFICATIONS 15° 25.10 FULLY EXTENDED 5° 32.00” 29.5 max” 1.75 min” 4.68” 24.61 25.50” .32 DIA TYP 3 13.
PAGE 4
MOUNTING HARDWARE 1 M8 X 16 PAN HEAD PHILLIPS MACHINE SCREW 4 REQUIRED 6 M6 X 16 PAN HEAD PHILLIPS MACHINE SCREW 4 REQUIRED 5/16 X 7/8 USS STEEL FLAT WASHER 6 REQUIRED 7 2 3 5-16 X 2 1/2 LAG BOLT 6 REQUIRED M5 X 16 PAN HEAD PHILLIPS MACHINE SCREW 4 REQUIRED 8 4 5 SQUARE MULTI WASHER 4 REQUIRED 1/4-20 X 1/2 PAN HEAD PHILLIPS SELF TAPPING MACHINE SCREW 8 REQUIRED CABLE MANAGEMENT BRACKET 8 REQUIRED 4 9 LOCKING TAB 2 REQUIRED 10 1/4-20 PAN HEAD PHILLIPS SCREW 2 REQUIRED
PAGE 5
1. FASTEN MOUNTING PLATE TO WALL Determine the exact mounting location for the wall mounting plate prior to the installation, considering the swing of the articulating arm. The plate must be secured to the CENTER of the wall studs capable of at least (4) times the weight of the display and AWM250 . The wall plate should be mounted at the same horizontal center line as the desired display center line (viewing horizontal center line).
PAGE 6
3. SECURE THE DISPLAY BRACKETS TO THE MONITOR Place the display panel on a protected surface. Position the display bracket with the round holes towards the bottom See Fig 3 Position the brackets equal distance from the bottom and top. Using the proper screws and the square multi washers supplied (1,2,3,8),insert and tighten hardware. See Fig 3a NOTE: Do not over tighten the bracket mounting screws as damage to the display internal mounting threads could occur.
PAGE 7
4. TYPICAL PDR PANEL MOUNTING TO ARTICULATING ARM, TENSION CONTROL Lift the display with the wall arms attached on to the AWM250 and center the display on the mounting plate. Assemble the locking tab (items 9 & 10) and insert into the slot in the display arm. (See Fig 4a & 4b) Center the display on the mounting plate and tighten the screws (10) on the locking tab (9). Care should be taken not to over tighten screws (10).
PAGE 8
5. DISPLAY PANEL ADJUSTMENT AND CABLE MANAGEMENT After placing the display on to the AWM250 articulating arm and securing the locking screw tabs, fine adjustments can be made for your best viewing. If the display is not level from left to right Loosen the display leveling bolts and adjust the display and re-tighten the bolts. To tilt the display up or down, loosen the tilt lock knob and adjust with the fine tilt adjuster to the desired view angle. Re-tighten the Tilt lock when complete.