Installation Guide

ManualsBrandsPeak Aluminum Railing ManualsLumber & Composites3-5/6 ft. x 3-1/3 ft. Black Wide Aluminum Single Walk Through Picket Gate

peakproducts.com

All fasteners are included with each component.

Tools & Materials Needed

• Hacksaw or metal cutting saw

• Drill

• Drill bits: 1/8", 1/4", 5/32", 7/32"

• 3/8" socket or wrench

• Phillips screwdriver

• Measuring tape

• Non-corrosive exterior silicone caulking

Lag bolt

Connector

Bolt

Phillips screw

Self-drilling screw

See WARNING on inside panel

Installation GuideInstallation Guide

U.S. VersionU.S. Version

Summary of content (7 pages)

PAGE 1
Installation Guide U.S. Version Tools & Materials Needed • Hacksaw or metal cutting saw • Drill • Drill bits: 1/8", 1/4", 5/32", 7/32" • 3/8" socket or wrench • Phillips screwdriver • Measuring tape • Non-corrosive exterior silicone caulking All fasteners are included with each component. Self-drilling screw Lag bolt Phillips screw Connector Bolt See WARNING on inside panel peakproducts.
PAGE 2
Dear Customer, We’d like to take a moment to say “thank you and congratulations” for choosing our products. At Peak™ your satisfaction is very important to us. That is why we work very hard to provide you with products of exceptional quality, value, and beauty. And that is also why we want to hear from you. Please contact us with your comments or suggestions at: quality@peakproducts.com Or if you prefer, write to us at: “Customer Care” The Peak Group of Companies P.O. Box 96060 Richmond, B.C.
PAGE 3
PICKET INSTALLATION Measure and mark the position of all posts and space equally. Fasten the end post in place - ensure that the post is plumb. Temporarily position the second post - do NOT secure it yet. Cut the hand and base rails to fit between the posts. Install the base rail support(s) into the bottom channel of the base rail and install all but the last four spacers into each rail. Remove the temporary post to install the last few pickets and spacers.
PAGE 4
GLASS PANEL INSTALLATION (18” wide or greater) Always use two people to handle glass panels. Always lift a glass panel by its sides. Tempered glass is extremely fragile – do not bump the edges. Always use protective gear including eyewear and gloves when handling glass panels. Measure and mark the position of all posts and space equally. Fasten the end post in place - ensure the post is plumb. Temporarily position the second post - do NOT secure it yet. Cut the hand and base rails to fit between the posts.
PAGE 5
6” wide GLASS PANEL KIT INSTALLATION IMPORTANT NOTICE: This kit was designed to fit perfectly in a 6’ railing section. If your railing is shorter than 6’, you will need to cut the spacers or remove glass panel(s) accordingly. Distance between glass panels or glass panel and post must never exceed 4”. The distance between a post and a glass panel must never exceed 4”. Always lift a glass panel by its sides. Tempered glass is extremely fragile – do not bump the edges.
PAGE 6
STAIR RAILING INSTALLATION Follow all applicable building codes for stair post placement and heights of rails above nose of stair treads. NOTE: Stair pickets and spacers are different from regular pickets and spacers. For United States stair railing installations, regular hand and base rails are not International Code Council compliant for graspability. Always use stair hand and base rail set for stair applications. Use Stair Connectors (SCs) at each post.
PAGE 7
GATE INSTALLATION Gate opening (W), must not exceed 46". Remove the latch side of the gate (Fig. 1). Cut the top and bottom gate rails 7 1/2" shorter than the gate opening (Fig. 2). Align the top rail of the gate with the handrails. Drill 5/32" pilot holes into the post and lag bolt the gate to the post. (Fig. 1) Installati U.S (Fig. 2) W ( 46" max) W minus 7 1/2" Tools & Materi Use self-drilling screws for these steps: - Secure the retainer to the gate frame at marked position.