Instructions / Assembly

ManualsBrandsPEAK ManualsFence Gate Hardware KitsAquatinePLUS 2 in. 2.5 in. x 5 in. Black Aluminum Pool Fence Picket Angle Bracket Kit

Installation Guide

Tools & materials required for each application

• Mitre saw with a non-ferrous

metal cutting blade

• Drill

• Phillips #2 & #3 bits

• Phillips #2 screwdriver

• Slot-head screwdriver

• Level

• Socket or wrench set

• Measuring tape

• Pencil

Concrete anchor

Concrete screw

Hard Surfaces

Soft Surfaces

• Post hole digger

• Shovel

• Concrete mixing

equipment

• Concrete trowel

• Dry premixed concrete (per post):

Fasteners included with each fence component

LED Application

• Drill bits for metal:

1/4", 1/2", 5/8“

• Hole saw for metal: 1"

• Small round metal ﬁle

• Scissors

All Applications

Rail & Picket Kit Rail Kit for Glass Panel

Hard Surface Post Yard Gate

Climate with frost heave - 200 lb.*

Climate without frost heave - 100 lb.*

*Quantities are estimated. Always check your

local codes for post hole size and depth.

• Hammer drill

• Masonry bits:

7/32", 5/16"

• Hammer

5/8" Self-drilling screw 5/8" Self-drilling screw

Connector bolt

1" Self-drilling screw

Hinge bolt

Pool Gate

1" Self-drilling screw

5/8" Self-tapping screw

U.S. VersionU.S. Version

Summary of content (8 pages)

PAGE 1
Installation Guide U.S. Version Tools & materials required for each application Hard Surfaces All Applications Soft Surfaces • Mitre saw with a non-ferrous metal cutting blade • Post hole digger • Hammer drill • Shovel • Masonry bits: • Concrete mixing 7/32", 5/16" equipment • Hammer • Concrete trowel • Dry premixed concrete (per post): • Drill • Phillips #2 & #3 bits • Phillips #2 screwdriver • Slot-head screwdriver • Level Climate with frost heave - 200 lb.
PAGE 2
Dear Customer, We’d like to take a moment to say “thank you and congratulations” for choosing our products. At Peak® your satisfaction is very important to us. That is why we work very hard to provide you with products of exceptional quality, value, and beauty. And that is also why we want to hear from you. Please contact us with your comments or suggestions at: quality@peakproducts.com Or if you prefer, write to us at: “Customer Care” The Peak Group of Companies P.O. Box 96060 Richmond, B.C.
PAGE 3
PICKET FENCE INSTALLATION (soft surface) 5 This symbol indicates important information 1 First post Second post rail length rail length ! If you plan to cut the rails Measure and mark the position of all posts and ensure they are aligned. Dig the post holes. ! If required, cut the rails to fit between the brackets. before assembling the fence panel, ensure the rails are correctly oriented before cutting. Always check your local codes for post hole size and depth.
PAGE 4
PICKET FENCE INSTALLATION (hard surface) ! 1 6 This symbol indicates important information A B 2 Measure and mark the position of all posts and ensure they are aligned. Put the first post in position. ! Maximum post spacing: 6' 2 5/8" on center. A: Use a hammer drill with a 5/16" masonry bit to drill four holes 3" deep through each corner of the post base. Clean the holes. B: Use a hammer to insert assembled concrete anchors until washer is touching post base. Use a 7/16" wrench to tighten the nuts.
PAGE 5
GLASS FENCE INSTALLATION (hard surface only) WARNING Always use two people to handle glass panels. Always lift a glass panel by its sides. Tempered glass is extremely fragile – do not bump the edges. Always use protective gear including eyewear and gloves when handling glass panels. 6 1 Measure and mark the position of all posts and ensure they are aligned. Put the first post in position.
PAGE 6
LED INSTALLATION READ AND FOLLOW ALL WARNINGS AND SAFETY INSTRUCTIONS INCLUDED INSIDE THE LED STARTER KIT CARTON. RISK OF INJURY, ELECTRICAL SHOCK AND FIRE. CONSULT A QUALIFIED ELECTRICIAN FOR CORRECT WIRING AND SUPPLY OF ELECTRICITY. WARNING 3A B A WARNING BE SURE TO DISCONNECT THE POWER SUPPLY FROM THE POWER SOURCE BEFORE THIS STEP. Ensure you drill the hole on the desired side of the post. C: Finish by drilling a 1/2" hole.
PAGE 7
POOL GATE INSTALLATION 5 B A C IMPORTANT: Always understand and comply with your local building codes for access gate requirements: • Height, clearances, and openings • Swing direction from the pool or spa • Distance between the tops of horizontal members • Self-closing • Location of the self-latching device above grade • Other specified requirements A: Position the striker with the bottom of the latch and mark the location of the mounting holes on the gate.
PAGE 8
YARD GATE INSTALLATION WARNING 3A Do not use for pool or spa applications. 1 A 42" B The opening between the fence posts must be 42". For Aquatine™ PLUS fence posts: Use 1" self-drilling screws (provided) for these steps: A: Align the bottom of the gate with the bottom of the fence, then fasten each U-bracket to the fence post.