PeakTech® 1240/1245/1255/ 1260/1270/1275 Bedienungsanleitung / Operation manual Digital Oscilloscopes
1. Sicherheitshinweise zum Betrieb des Gerätes Dieses Gerät erfüllt die EU-Bestimmungen 2004/108/EG (elektromagnetische Kompatibilität) und 2006/95/EG (Niederspannung) entsprechend der Festlegung im Nachtrag 2004/22/EG (CE-Zeichen). Überspannungskategorie II; Verschmutzungsgrad 2. Zur Betriebssicherheit des Gerätes und zur Vermeidung von schweren Verletzungen durch Strom- oder Spannungsüberschläge bzw.
* Warnung!: Ist das Oszilloskop mit einem Eingangssignal von mehr als 42V spitze (30Veff) oder Schaltungen mit mehr als 4800VA verbunden, beachten Sie bitte die unten aufgeführten Hinweise, um Feuer oder einen elektrischen Schlag zu vermeiden: - Verwenden Sie nur isolierte Tastköpfe und Messleitungen. - Prüfen Sie sämtliches Zubehör vor dem Gebrauch und ersetzen Sie es bei Beschädigungen. Im Zweifel keine Messungen vornehmen.
Gefahr: Hoch- siehe Betriebs- spannung anleitung Masseklemme Schutzleiterklemme Gerätemasse (Erde) 3.
1. 2. 3. 4. 8. 7. 6. 5. Abb. 1 1. Ein/Aus 2. Anzeigebereich 3. Stromversorgungsanzeige Grünes Licht: Zeigt an, dass das Oszilloskop am Netzstrom angeschlossen und die Batterie voll ist (falls sich eine Batterie im Oszilloskop befindet). Gelbes Licht: Zeigt an, dass das Oszilloskop am Netzstrom angeschlossen ist und die Batterie aufgeladen wird (falls sich eine Batterie im Oszilloskop befindet). Licht aus: Nur batteriebetrieben, ohne Anschluss an den Netzstrom. 4.
3.3. Linke Seite 1. 2. Abb. 2 Linke Seite des Oszilloskops 1. Netzschalter: “―” heißt Gerät EIN; “○” heißt Gerät AUS. 2. Netzeingangsbuchse 3.4. Rechte Seite 1. 2. 3. 4. Abb. 3 Rechte Seite des Oszilloskops 1. USB Host-Anschluss: Wird verwendet, um Daten zu übertragen, wenn ein externes, an das Oszilloskop angeschlossenes USB-Gerät als “Host-Gerät” angesehen wird. Zum Beispiel: Dieser Anschluss wird beim Upgrade der Software über USB Flash Disk verwendet. 2.
3. VGA-Anschluss: Um das Oszilloskop an einen Bildschirm oder Projektor als VGA-Ausgang anzuschließen. 4. LAN-Anschluss: Der Netzwerkanschluss, der zum Anschluss eines Computers verwendet werden kann, um z.B. das Oszilloskop in ein bestehendes Netzwerk zu integrieren. 3.5. Rückseite 1. 2. 3. 4. 5. 4. Abb. 4 Rückseite des Oszilloskops 1. Anschluss für den Triggersignal-Ausgang & Pass/Fail-Ausgang 2. Tragegriff 3. Belüftung 4. Fußstütze (zum Einstellen des Kippwinkels des Oszilloskops) 5.
3.6. Steuerbereich (Tasten und Drehknöpfe) 4. 1. 2. 3. 5. 6. 7. 8. Abb. 5 Überblick über die Tasten 1. Menü-Optionseinstellung: H1~H5 2. Menü-Optionseinstellung: F1~F5 3. Menu off: Menü ausstellen 4. Multipurpose: Mehrzweck-Drehknopf („M-Drehknopf“) 5. Funktionstastenbereich: Insgesamt 12 Tasten 6. Vertikaler Regelbereich mit 3 Tasten und 4 Drehknöpfen.
3.7. Einführung in die Benutzeroberfläche Abb. 6 Benutzeroberfläche 1. Wellenform-Anzeigebereich. 2. Der Triggerstatus, einschließlich: Auto: Automatik-Modus und Wellenformerfassung ohne Triggerung. Trig: Trigger erkannt und Wellenform wird erfasst. Ready: Vor dem Triggersignal eintreffende Daten wurden aufgezeichnet und das Gerät ist für das Triggersignal bereit. Scan: Kontinuierliches Aufzeichnen und Anzeigen der Wellenform. Stop: Aufzeichnung der Wellenform gestoppt. 3.
18/19. Der aktuelle Triggertyp: Trigger auf der steigenden Flanke Trigger auf der fallenden Flanke Videozeilen-Synchrontrigger Videofeld-Synchrontrigger Zeigt den Wert des Triggerpegels des entsprechenden Kanals an. 20. Zeigt den Nominalwert für die Fensterzeitbasis an. 21. Zeigt die Einstellung der Hauptzeitbasis an. 22. Zeigt die aktuelle Abtastrate und die Record-Länge an. 23. Zeigt den gemessenen Typ und Wert des entsprechenden Kanals an.
2. Überprüfen des Zubehörs Das mitgelieferte Zubehör wird in Anhang B “Zubehör” dieses Handbuchs beschrieben. Prüfen Sie das Zubehör anhand dieser Beschreibung auf seine Vollständigkeit. Sollten Zubehörteile fehlen oder beschädigt sein, wenden Sie sich bitte an Ihren Händler. 3. Überprüfen des Geräts Sollten Sie Schäden am Äußeren des Geräts feststellen oder aber das Gerät funktioniert nicht ordnungsgemäß oder besteht die Leistungsprüfung nicht, wenden Sie sich bitte an Ihren Händler.
Abb. 7 Automatische Einstellungen (Autoset) Prüfen Sie CH2 durch Wiederholen der Schritte 2 und 3. 5. Durchführen der Tastkopfkompensation Wenn Sie den Tastkopf zum ersten Mal mit einem Eingangskanal verbinden, müssen Sie den Tastkopf an den Eingangskanal anpassen. Ein nicht oder falsch kompensierter Tastkopf ergibt Messfehler. Führen Sie die Tastkopfkompensation wie folgt durch: 1.
3. Wiederholen Sie die Schritte, falls nötig. Abb. 9 Tastkopfjustierung 6. Einstellen des Tastkopfdämpfungsfaktors Der Tastkopf besitzt mehrere Tastkopfdämpfungsfaktoren, die den Vertikalskalierungsfaktor des Oszilloskops beeinflussen. Wenn der eingestellte Tastkopfdämpfungsfaktor geändert oder überprüft werden soll, drücken Sie die Taste für das Funktionsmenü des jeweiligen Kanals und dann die dem Tastkopf entsprechende Auswahltaste, bis der richtige Wert angezeigt wird.
7. Durchführen der Auto-Kalibrierung Mit der Auto-Kalibrierung lässt sich das Oszilloskop schnell in den optimalen Zustand für hochgenaue Messungen versetzen. Sie können dieses Programm jederzeit ausführen, müssen dies jedoch tun, wenn die Umgebungstemperatur um mehr als 5° C variiert. Entfernen Sie alle Tastköpfe und Kabel von den Eingangsbuchsen, bevor Sie die Auto-Kalibrierung durchführen.
2. Ändern Sie die Vertikaleinstellung und beobachten Sie die daraus resultierende Änderung der Statusinformation. Mit den Statusinformation, die unten im Wellenfenster angezeigt werden, können Sie Änderungen des vertikalen Skalierfaktors für den Kanal erkennen. 3. Vertikalen Offset wieder auf 0 stellen: Drehen Sie den Knopf VERTICAL POSITION, um die vertikale Position des Kanals zu verändern und drücken Sie den VERTICAL POSITION - Knopf, um die vertikale Position auf 0 zurück zusetzen.
1. Mit dem Einstellknopf „SEC/DIV“ ändern Sie die Einstellungen für die horizontale Zeitbasis; Sie können dann die daraus resultierenden Änderungen der Statusinformationen beobachten. Drehen sie den Einstellknopf „SEC/DIV“, um die horizontale Zeitbasis zu verändern; Sie sehen dann die entsprechenden Änderungen in der Anzeige „Horizontal Time Base“ in der Statuszeile. 2. Mit dem Einstellknopf „HORIZONTAL POSITION“ stellen Sie die horizontale Position des Signals im Wellenformfenster ein.
11. Einstellung des vertikalen Systems Die VERTIKALEN BEDIENELEMENTE umfassen die drei Menütasten CH1 MENU, CH2 MENU und MATH sowie die vier Einstellknöpfe VERTICAL POSITION, VOLTS/DIV (eine Gruppe für jeden der beiden Kanäle). Einstellungen für Kanal 1 und 2 Jeder Kanal besitzt ein eigenes Vertikal-Menü, und jede Einstellung wird separat für den jeweiligen Kanal vorgenommen. Drücken Sie die Menütaste „CH1 MENU“ oder „CH2 MENU“, um das Bedienmenü für den entsprechenden Kanal anzuzeigen (siehe Abb. 14).
Die folgenden Tabelle beschreibt die Einträge des Channel Menu: Funktion Mögliche Beschreibung Einstellung Kupplung AC Blockiert die DC-Komponente im Eingangssignal. DC Lässt AC- und DC-Komponenten, im Eingangssignal, passieren. Invertiert Tastkopfeinstellung Ground Eingangssignal ist unterbrochen Aus Die Wellenform wird normal angezeigt.
Abb. 15 Oszillogramm der Wechselstromkopplung 11.2. Einschalten/Ausschalten eines Kanals Gehen Sie wie folgt vor, um dies z.B. für Kanal 1 zu tun: 1. Drücken Sie die Taste CH1 MENU, um das Menü CH1 SETUP aufzurufen. 2. Drücken Sie die Taste CH1 um Kanal 1 auszuschalten. 3. Drücken Sie die Taste CH1 erneut um Kanal 1 wieder einzuschalten. 11.3.
Abb. 16 Einstellen des Tastkopf-Dämpfungsfaktors Eine Liste von Dämpfungs-Koeffzizienten von Tastköpfen und die entsprechenden Menü-Einstellungen. Dämpfungs-Koeffizient des Tastkopfes entsprechende Menü-Einstellungen 1:1 1X 10:1 10X 100:1 100X 1000:1 1000X 11.4. Einstellen der invertierten Wellenform Bei der invertierten Wellenform wird das angezeigte Signal um 180 Grad gegenüber der Phase des Erdungspotentials gedreht. Gehen Sie wie folgt vor, um dies z.B. für Kanal 1 zu tun: 1.
Abb. 17 Wellenform nicht invertiert Abb. 18 Wellenform invertiert 11.5. Einstellen der Bandbreitenbegrenzung (nur P 1245/1255/1260) Wenn die Hochfrequenzkomponenten einer Wellenform nicht wichtig für ihre Analyse sind, kann die Bandbreitenbegrenzung eingesetzt werden, um Frequenzen über 20 MHz zu unterdrücken. Gehen Sie wie folgt vor, um dies z.B. für Kanal 1 zu tun: 1. Drücken Sie die Taste CH1 MENU, um das Menü CH1 SETUP aufzurufen. 2. Drücken Sie die Taste H4.
12. Anwendung der Mathematikfunktion Die Mathematical Manipulation-Funktion zeigt die Ergebnisse von Additionen, Multiplikationen, Divisionen und Subtraktionen angewandt auf Kanal 1 und Kanal 2 sowie die FFT-Operation von Kanal 1 bzw. Kanal 2. Abb.
Gehen Sie wie folgt vor, um z.B. eine Addition von Kanal 1 und 2 vorzunehmen: 1. Drücken Sie die Math-Taste, um das Wfm Math-Menü aufzurufen. 2. Drücken Sie die Taste H1 und rufen Sie das Menü Dual Wfm Math auf. Das Menü wird auf der linken Bildschirmseite angezeigt. 3. Drücken Sie die Menüauswahltaste F1 und wählen Sie CH1 bei Factor1. 4. Drücken Sie die Menüauswahltaste F2 und wählen Sie +. 5. Drücken Sie die Menüauswahltaste F3 und wählen Sie CH2 bei Factor2.
Funktionsmenü FFT Source (Quelle) Einstellung Beschreibung ON (Ein) Einschalten der FFT-Funktion OFF (Aus) Ausschalten der FFT-Funktion CH1 Auswahl von Kanal 1 als FFT-Quelle CH2 Auswahl von Kanal 2 als FFT-Quelle Rechteck Window (Fenster) Blackman Hanning Auswahl des FFT-Fensters Hamming Format Zoom dB Auswahl von dB als Format Vrms Auswahl von Vrms als Format x1 Faktor auf x1 setzen x2 Faktor auf x2 setzen x5 Faktor auf x5 setzen x10 Faktor auf x10 setzen Beispiel für die Schri
Typ Beschreibung Fenster Dieses Fenster eignet sich am besten für Frequenzauflösungen, ist aber das schlechteste für die genaue Messung der Amplitude dieser Frequenzen. Es ist das beste Fenster für die Messung des Frequenzspektrums von nicht repetitiven Signalen und der Messung von Rechteck Frequenzanteilen nahe DC. (Rectangle) Verwenden Sie das Rechteckfenster für die Messung von Transienten oder Spitzen, bei denen das Signalniveau vor und nach dem Ereignis fast gleich ist.
Abb. 21 Rechteck Fenster Abb. 22 Hamming-Fenster Abb.
Abb. 24 Blackman-Fenster Schnelltipps * Falls gewünscht, verwenden Sie die Zoom-Funktion zur Vergrößerung der FFT-Kurve. * Verwenden Sie die dBV RMS-Skala für eine detaillierte Ansicht mehrerer Frequenzen, selbst wenn diese unterschiedliche Amplituden haben. Verwenden Sie die lineare RMS-Skala, um in einer Gesamtansicht alle Frequenzen miteinander zu vergleichen. * Signale, die einen DC-Anteil oder Versatz enthalten, können zu falschen FFT-Signal-Amplitudenwerten führen.
14. Bedienung der Einstellknöpfe VERTICAL POSITION und VOLTS/DIV 1. Mit dem Einstellknopf VERTICAL POSITION verändern Sie die vertikale Position der Wellenformen aller Kanäle (einschließlich der durch mathematische Berechnung entstandenen). Die Auflösung dieses Einstellknopfes verändert sich mit der vertikalen Teilung. 2.
Abb. 26 Menü Time Mode Das Horizontal-Menü wird im Folgenden beschrieben: Funktions-Menü Einstellungen Main Time Base Beschreibung Die Einstellung der horizontalen Hauptzeitbasis wird benutzt, um die Wellenform anzuzeigen. Set (Set Window) Ein Bereich wird mit zwei Cursorn definiert. Zoom Der definierte Bereich wird vergrößert und als Vollbild angezeigt. 16. Hauptzeitbasis Drücken Sie die Menüauswahltaste H1 und wählen Sie Haupt-Zeitbasis.
17. Fenstereinstellung Drücken Sie die Menüauswahltaste H2 und wählen Sie Set Fenster. Auf dem Bildschirm erscheinen zwei einen Ausschnitt definierende Cursor. In diesem Fall können Sie die Einstellknöpfe HORIZONTAL POSITION und SEC/DIV verwenden, um die Horizontalposition sowie die Größe dieses Fensters einzustellen (siehe Abb. 28). Abb. 28 Fenstereinstellung 18. Fenstervergrößerung Drücken Sie die Menüauswahltaste H3 und wählen Sie Fenster.
19. Einstellen des Triggersystems Der Trigger legt fest, wann das OSZILLOSKOP mit dem Erfassen von Daten und der Anzeige der Wellenform beginnt. Einmal richtig eingestellt, kann der Trigger eine schwankende Anzeige in eine sinnvolle Wellenform umwandeln. Wenn das OSZILLOSKOP mit der Datenerfassung beginnt, zeichnet es ausreichend Daten auf, um die Wellenform links vom Triggerpunkt darzustellen. Das OSZILLOSKOP setzt die Datenerfassung fort, während es auf eine Triggerbedingung wartet.
1. Edge Ein Edge-Trigger tritt beim Trigger-Schwellenwert des Eingangssignals auf. Wählen Sie den Edge-Triggermodus, um auf der ansteigenden oder abfallenden Flanke des Signals zu triggern. Abb. 30 zeigt das Menü Edge Trigger. Abb. 30 Edge-Triggermenü Das Edge-Menü: Menü Einstellungen Beschreibung Single Edge Einstellen des Triggertyps für den vertikalen Kanal als Edge-Trigger. CH1 Kanal 1 als Triggersignal. CH2 Kanal 2 als Triggersignal.
2. Video Wählen Sie den Video-Modus, um auf Videofeldern oder Videozeilen von NTSC-, PAL- oder SECAM-Standardvideosignalen zu triggern. Für das Triggermenü siehe Abb. 31 Abb. 31 Video-Triggermenü Das Video-Menü: Menü Einstellungen Beschreibung Single Video Einstellen des Triggertyps für den vertikalen Kanal als Video-Trigger. CH1 Auswahl von CH1 als Triggerquelle. CH2 Auswahl von CH2 als Triggerquelle. EXT Externer Triggereingang EXT/5 1/5 der externen Triggerquelle für steigenden Messbereich.
Das Slope-Menü: Menü Single Source Einstellungen Beschreibung Einstellen des Triggertyps für den vertikalen Kanal als Slope Slope-Trigger. CH1 Auswahl von CH1 als Triggerquelle. CH2 Auswahl von CH2 als Triggerquelle. Slope Slope-Auswahl When Einstellen der Slope-Bedingung; Einstellen der Slope-Zeit mithilfe des M-Drehknopfes. High level Threshold &SlewRate Einstellen der oberen Grenze des High-Pegels mithilfe des M-Drehknopfes.
Das Pulse-Menü: Menü Einstellungen Beschreibung Single Pulse Einstellen des Triggertyps für den vertikalen Kanal als Impuls-Trigger. CH1 Auswahl von CH1 als Triggerquelle. CH2 Auswahl von CH2 als Triggerquelle. AC Blockiert DC-Anteil. DC Lässt alle Anteile durch. HF Blockiert das HF-Signal und lässt nur den NF-Anteil durch. LF Blockiert das NF-Signal und lässt nur den HF-Anteil durch. Source Couple Polarity Auswahl der Polarität.
6. Alternierender Trigger (Triggermodus: Edge) Das Alternierender Trigger (ALT) (Triggertyp: Abb. 34 zeigt das Menü Alternate Trigger. Abb.34 Menü für alternierenden Trigger (ALT) (Triggertyp: Edge) Das Alternierender Trigger (ALT) (Triggertyp: Edge) -Menü: Menü Einstellungen Alternate (ALT) Edge Source Couple Einstellen des Triggertyps für den vertikalen Kanal als Edge-Trigger. CH1 Auswahl von CH1 als Triggerquelle. CH2 Auswahl von CH2 als Triggerquelle. AC Blockiert DC-Anteil.
7. Alternierender Trigger (Triggermodus: Video) Das Alternierender Trigger (ALT) (Triggertyp: Video) wird in Abb. 35 dargestellt. Abb. 35 Menü für alternierenden Trigger (ALT) (Triggertyp: Video) Das Alternierender Trigger (ALT) (Triggertyp: Video) -Menü: Menü Einstellungen Alternate (ALT) Video Source Beschreibung Einstellen des Triggertyps für den vertikalen Kanal als Video-Trigger. CH1 Auswahl von CH1 als Triggerquelle. CH2 Auswahl von CH2 als Triggerquelle.
Das Alternierender Trigger (ALT) (Triggertyp: Slope) Menü: Menü Alternate (ALT) Source Einstellungen Beschreibung Slope Einstellen des Triggertyps für den vertikalen Kanal als Slope-Trigger. CH1 Auswahl von CH1 als Triggerquelle. CH2 Auswahl von CH2 als Triggerquelle. Slope Auswahl der Slope-Bedingung. When Einstellen der Slope-Bedingung; Einstellen der Zeit mithilfe des M-Drehknopfes. Threshol d Holdoff High level Einstellen des High-Pegels mithilfe des M-Drehknopfes.
Das Alternierender Trigger (ALT) (Triggertyp: Pulse) Menü: Menü Einstellungen Alternate (ALT) Pulse Source Couple Beschreibung Einstellen des Triggertyps für den vertikalen Kanal als Impuls-Trigger. CH1 Auswahl von CH1 als Triggerquelle. CH2 Auswahl von CH2 als Triggerquelle. AC Blockiert DC-Anteil. DC Lässt alle Anteile durch. HF Blockiert das HF-Signal und lässt nur den NF-Anteil durch. Blockiert das NF-Signal und lässt nur den HF-Anteil durch. LF Polarity Auswahl der Polarität.
2. Trigger Mode: Der Triggermodus legt fest, wie sich das Oszilloskop bei Fehlen eines Triggerereignisses verhält. Das Oszilloskop bietet drei Trigger-Modi: Auto, Normal und Single. * Auto: Bei diesem Wobbel-Modus erfasst das Oszilloskop Wellenformen, auch wenn es keine Triggerbedingung erkennt. Es erfolgt eine Zwangstriggerung, wenn während einer bestimmten Wartezeit keine Triggerbedingung eintritt (gemäß der Zeitbasis-Einstellung).
20. Einrichten der Abtastfunktion Drücken Sie die Taste ACQUIRE; auf dem Bildschirm erscheint das Menü wie in Abb. 38 gezeigt. Abb. 38 Menü ACQU MODE Die folgende Tabelle beschreibt das Menü Sampling Setup: Funktion Mögliche Beschreibung Einstellung Abtastung Allgemeiner Abtastmodus. May Erkennung Dient zur Erkennung von Störspitzen und zur Verringerung von Störungen.
Verändern Sie die ACQU-Mode-Einstellungen, um konsequent Veränderungen des Wellenformsignals zu beobachten. Abb. 39 Max Erkennungs-Mode, mit deren Hilfe die Spitzen der fallenden Flanke ermittelt werden können und Rauschen festgestellt wird. Abb. 40 übliche ACQU-Mode-Anzeige an der keine Spitzen ermittelt werden können Abb. 41 die angezeigte Wellenform nachdem das Rauschen mit dem Average Mode entfernt wurde. Die Averagenummer wurde eingestellt auf 16.
21. Einstellung des Anzeigesystems Drücken Sie die Taste DISPLAY; auf dem Bildschirm erscheint das Menü wie in Abb. 42 gezeigt. Abb. 42 Menü Display Set Die folgende Tabelle beschreibt das Menü Display Set: Funktion Mögliche Beschreibung Einstellung Type Vectors Der Raum zwischen benachbarten Abtastpunkten in der Anzeige wird mit einer Vektorkurve gefüllt. Persist Dots Nur die Abtastpunkte werden angezeigt. OFF Legt die Nachleuchtzeit für jeden Abtastpunkt fest.
Anzeigetyp: Drücken Sie die Menüauswahltaste F1, um zwischen Vektor- und Punktdarstellung hin- und herzuschalten. Die Abbildungen 43 und 44 zeigen die Unterschiede in der Darstellung. Abb. 43 Anzeige im Vektorformat Abb.
22. Nachleuchten Mit der Funktion Persist können Sie den Nachleuchteffekt eines Röhrenoszilloskops simulieren: die gespeicherten Originaldaten werden verblasst, die neuen Daten in kräftiger Farbe dargestellt. Drücken Sie die Taste „Display“ und H2, um dann mit der Menüauswahltaste F2 die verschiedenen Nachleuchtzeiten auszuwählen: 1sec, 2sec, 5sec, Infinite und Clear. Wenn Sie für die Nachleuchtzeit „Infinite“ wählen, werden die Messpunkte gespeichert, bis Sie die Nachleuchtzeit wieder ändern (siehe Abb.
Bedienung: 1. Drücken Sie die Taste DISPLAY, um das Menü Display Set Menu aufzurufen. 2. Drücken Sie die Menüauswahltaste H3 und wählen Sie XY bei Format. Das Anzeigeformat wechselt in den XY-Modus (siehe Abb. 46). Abb. 46 Anzeigeformat XY 24. Cymometer (Wellenmesser) Hierbei handelt es sich um ein 6-stelliges Cymometer. Das Cymometer kann Frequenzen von 2Hz bis zur vollen Bandbreite messen.
25. VGA-Ausgang Am VGA-Ausgang kann ein Computermonitor angeschlossen werden. Das Bild des Oszilloskops kann so deutlich auf dem Monitor angezeigt werden. So stellen Sie den VGA-Ausgang ein: 1. Drücken Sie die Display-Taste. 2. Drücken Sie im Display-Menü die Taste H5, um zwischen EIN bzw. AUS hin- und herzuschalten. 26. Speichern und Laden einer Wellenform Durch Drücken der Save (Speichern) -Taste können Sie die Wellenformen, Einstellungen oder Bildschirmdarstellungen speichern. Abb.
Speichern im internen Speicher (“Internal”) oder im USB-Speicher („External“). Wird die Option External (Extern) gewählt, wird die Storage Internal External Wellenform entsprechend ihrer aktuellen Aufzeichnungslänge gespeichert (s. “27. Speichern und Laden von Wellenformen” auf S. 48). Der Dateiname ist editierbar. Die Wellenform-Datei kann mit ® der PeakTech - Signalanalyse-Software geöffnet werden (auf der mitgelieferten CD).
Abb. 48 Tipp: Mit der COPY-Taste können Sie die aktuell angezeigte Wellenform einfach und schnelle in jeder Benutzeroberfläche auf einen extern verbundenen USB-Speicher speichern. Das Datenformat ist BIN, welches mit der beiliegend Gerätesoftware bearbeitet werden kann. Wurde im Speichermenü unter Storage (Speicherort) die Option “External” (extern) gewählt, sollten Sie einen USB-Speicher anschließen.
Letztes Zeichen löschen Beenden und speichern Umschalten zwischen Groß- und Tastatur schließen Kleinschreibung Abb. 49 Tipp: Nach dem oben genannten Schritt 3, mit dem Sie im Speichermenü unter Type die Option “Image” wählen, können Sie die aktuelle Bildschirmdarstellung in jeder Benutzeroberfläche durch Drücken der Copy-Taste speichern. Das Datenformat ist BIN, welches mit der beiliegend Gerätesoftware bearbeitet werden kann. 27.1.
Hinweis: Sowohl die Wellenformen von Kanal 1 als auch die Wellenform von Kanal 2 wird aufgezeichnet. Wird ein Kanal während der Aufzeichnung abgeschaltet, kann die Wellenform dieses Kanals im Playback-Modus nicht wiedergegeben werden. Abb. 50 Wellenform-Aufzeichnung Playback: Wiedergeben einer aufgezeichneten bzw. gespeicherten Wellenform. Das Playback-Menü: Menü Einstellung Beschreibung Start frame Auswahl der Anzahl von wiederzugebenden Start-Frames (1 ~ 1000) mithilfe des M-Drehknopfes.
Abb. 51 Wellenform-Wiedergabe Storage: Speichern der aktuellen Wellenform entsprechend des eingestellten Start- und End-Frames. Das Storage-Menü: Menü Einstellung Storage Start frame Mode FrameSet End frame Beschreibung Auswahl der Anzahl von zu speichernden Start-Frames (1 ~ 1000) mithilfe des M-Drehknopfes Auswahl der Anzahl von zu speichernden End-Frames (1 ~ 1000) mithilfe des M-Drehknopfes Save Speichern der Wellenform-Aufzeichnungsdatei im internen Speicher.
So verwenden Sie die Wellenform-Aufzeichnungsfunktion: 1. Drücken Sie die Save-Taste. 2. Drücken Sie die Taste H1 und wählen Sie mithilfe des M-Drehknopfes die option Record (Aufzeichnen). 3. Drücken Sie die Taste H2. Drücken Sie im Mode-Menü die Taste F2, um die Option Record (Aufzeichnen) zu wählen. 4. Drücken Sie die Taste H3.
Das Konfigurations-Menü: Funktionsmenü Einstellung Beschreibung Chinese Language Auswahl der Anzeigesprache (Chinesisch, Englisch, andere) des English Betriebssystems. Others Display Set Time On Off Ein-/Ausschalten der Datumsanzeige Hour Min Einstellen von Stunde/Minute Day Month Einstellen von Tag/Monat. Year Einstellen des Jahres. Sperrt alle Tasten. Freigabe: Drücken Sie die 50%-Taste im KeyLock Triggersteuerbereich und drücken Sie dann die Force-Taste. Wiederholen Sie dies 3-mal.
Das Adjust-Menü: Funktionsmenü Einstellung Beschreibung Self Cal Ausführen der Selbstkalibrierung. Default Aufrufen der Werkseinstellungen. Ausführen der Selbstkalibrierung (Self Cal) Die Selbstkalibrierungsfunktion dient dazu, die Genauigkeit des Oszilloskops bei veränderter Umgebungstemperatur so weit wie möglich zu erhöhen.
Das Pass/Fail-Menü: Funktionsmenü Operate Output Rule Einstellung Beschreibung Enable Steuerungs-Aktivierungsschalter Operate Steuerungs-Betriebsschalter Pass Geprüftes Signal entspricht der Regel. Fail Geprüftes Signal entspricht nicht der Regel. Beep Piepton (Beep), wenn das Signal der Regel entspricht. Stop Stopp, sobald das Signal der Regel entspricht. Info Steuern des Anzeigenstatus des Inforahmens. Source Auswahl der Quelle CH1, CH2 oder Math.
6. Regel speichern: Drücken Sie zuerst die Taste H5 und dann die Taste F2, um die Regeln zu speichern, die bei Bedarf durch Drücken der Taste F3 wieder aufgerufen werden können. Abb.58 Pass/Fail-Prüfung Hinweis: 1. Wenn die Pass/Fail-Funktion aktiviert wurde, doch XY oder FFT ausgeführt wird, wird die Pass/Fail-Funktion geschlossen. In den Modi XY oder FFT kann die Pass/Fail-Funktion nicht aktiviert werden. 2. In den Modi Factory, Auto Scale und Auto Set wird die Pass/Fail-Funktion ebenfalls geschlossen.
Das Output-Menü: Funktionsmenü Type Einstellung Beschreibung Trig level Synchrone Ausgabe des Triggersignals. Pass/Fail Ausgabe von High-Pegel bei “Pass” und von Low-Pegel bei „Fail“. 27.2.6. LAN Set Über den LAN-Anschluss kann das Oszilloskop direkt oder über einen Router an einen Computer angeschlossen werden. Die Netzwerkparameter können in dem unten beschriebenen Menü eingestellt werden.
Abb. 61 ® Einstellen der Netzwerkparameter der PeakTech Oszilloskop-Software: Führen Sie die Software auf dem Computer aus. Wählen Sie im Menüpunkt “Communications” die Option “Ports-settings” (Porteinstellungen). Setzen Sie die Option “Connect using” (Verbinden über) auf LAN. Die ersten drei Byte der IP-Adresse sind dieselben wie bei der IP-Adresse in Schritt (2). Das letzte Byte sollte anders lauten. Bei diesem Beispiel setzen wir die Adresse auf 192.168.1.72.
Einstellen der Netzwerkparameter des Oszilloskops: Drücken Sie beim Oszilloskop zunächst die Utility-Taste und danach die Taste H1. Wählen Sie mithilfe des M-Drehknopfes die Option LAN Set (LAN-Einstellung) aus. Drücken Sie die Taste H2. Das Einstellungsmenü wird rechts angezeigt. Setzen Sie die IP und den Port auf denselben Wert wie in Schritt 3 der Software-Einrichtung unter “Porteinstellungen” (Ports-settings) angegeben. Drücken Sie zur Bestätigung die Taste F5.
Abb. 64 ® Einstellen der Netzwerkparameter der PeakTech Oszilloskop-Software: Führen Sie die Software auf dem Computer aus. Wählen Sie im Menüpunkt “Communications” die Option “Port-settings” (Porteinstellungen). Setzen Sie die Option “Connect using” (Verbinden über) auf LAN. Die ersten drei Byte der IP-Adresse sind dieselben wie bei der IP-Adresse in Schritt (2). Das letzte Byte sollte anders lauten. Bei diesem Beispiel setzen wir die Adresse auf 192.168.1.72.
Einstellen der Netzwerkparameter des Oszilloskops: Drücken Sie beim Oszilloskop zunächst die Utility-Taste und danach die Taste H1. Wählen Sie mithilfe des M-Drehknopfes die Option LAN Set (LAN-Einstellung) aus. Drücken Sie die Taste H2. Das Einstellungsmenü wird rechts angezeigt. Setzen Sie die IP und den Port auf denselben Wert wie in Schritt 3 der Software-Einrichtung unter “Porteinstellungen” (Ports-settings) angegeben. Das Netgate sollte entsprechend des Routers eingestellt werden.
Abb.
Zur Messung der Frequenz, der Spitze-Spitze-Spannung des Kanals CH1 und der Mittelwert der RMS des Kanals CH2 gehen Sie wie unten beschrieben vor: 1. Drücken Sie die MEASURE-Taste, um das Menü der automatischen Messfunktionen anzuzeigen. 2. Drücken Sie die Taste H1, um das Menü “Hinzufügen” anzuzeigen. 3. Drücken Sie die Taste F2, um CH1 als Quelle auszuwählen. 4. Drücken Sie die Taste F1. Eine Auswahl der zur Verfügung stehenden Messungen wird auf der linken Seite des Bildschirms angezeigt.
30. Automatische Messung der Spannungsparameter Das Oszilloskop bietet automatische Spannungsmessungen einschließlich Vpp, Vmax, Vmin, Vavg, Vamp, Vrms, Vtop, Vbase, Overshoot und Preshoot. Abb. 69 gibt einen Impuls mit einigen Spannungsmesspunkten wieder. Abb. 69 Vpp: Spitze-Spitze-Spannung. Vmax: Maximale Amplitude. Die höchste positive Spitzenspannung, die über die gesamte Kurve gemessen wurde. Vmin: Minimale Amplitude.
Abb. 70 Rise Time: (Anstiegszeit) Die Zeit, die die Vorderflanke des ersten Impulses in der Kurve benötigt, um von 10% auf 90% ihrer Amplitude zu steigen. Fall Time: (Abfallzeit) Die Zeit, die die Vorderflanke des ersten Impulses in der Kurve benötigt, um von 90% auf 10% ihrer Amplitude zu fallen. +Width: Die Breite des ersten positiven Impulses am 50%-Amplitudenpunkt. -Width: Die Breite des ersten negativen Impulses am 50%-Amplitudenpunkt.
Bei Messungen mit dem Cursor können Sie die Position von Cursor 1 mit dem Einstellknopf CURSOR1 (VERTICAL POSITION) von Kanal 1, die von Cursor 2 mit dem Einstellknopf CURSOR2 (VERTICAL POSITION) von Kanal 2 verändern. Gehen Sie wie folgt vor, um die Spannungsmessung mit dem Cursor für Kanal 1 durchzuführen: 1. Drücken Sie CURSOR und öffnen Sie das Menü Curs Meas. 2. Drücken Sie die Menüauswahltaste H2 und wählen Sie CH1 als Quelle. 3. Drücken Sie die Taste H1 , um das Menü Typ anzuzeigen.
4. Stellen Sie die Positionen von CURSOR1 und CURSOR2 entsprechend der zu messenden Wellenform ein; es erscheinen dann Zyklus und Frequenz von Cursor 1 und Cursor 2 im Fenster. Die aktuelle Position von Cursor 1 wird unter Cursor1, die von Cursor 2 unter Cursor2 angezeigt (siehe Abb. 73). Abb. 73 Wellenform bei der Messung mit dem Cursor 32. Cursor-Messung für FFT-Modell: Drücken Sie die Taste Cursor, um das Menü für Messungen mit dem Cursor (CURS MEAS) aufzurufen.
Das Curs Meas-Menü: Funktionsmenü Einstellung Beschreibung OFF Schaltet die Messung mit dem Cursor aus. Vamp Zeigt den Cursor der Spannungsmessung und das Typ entsprechende Menü an. Freq Zeigt den Cursor der Frequenzmessung und das entsprechende Menü an. Quelle Math FFT Zeigt den Kanal für die Messung mit dem Cursor an.
Gehen Sie wie folgt vor, um die Frequenzmessung mit dem Cursor durchzuführen: 1. Drücken Sie Cursor-Taste und öffnen Sie das Menü Curs Meas. 2. Drücken Sie die Taste H1. Das Typ-Menü erscheint rechts im Bildschirm. Drücken Sie die Menüauswahltaste F3 und wählen Sie Freq bei Typ. Es erscheinen zwei violett gepunktete Vertikallinien, die auf die entsprechenden Cursor1 und Cursor2 verweisen. 3.
33. Verwenden der Autoscale-Funktion Hierbei handelt es sich um eine sehr nützliche Funktion für Erstanwender, die eine einfache und schnelle Prüfung des Eingangssignals durchführen möchten. Diese Funktion wird zur automatischen Verfolgung von Signalen verwendet, selbst wenn sich die Signale zu jeder Zeit ändern.
Die Wellenform wird nun wie in Abb. 78 dargestellt auf dem Bildschirm angezeigt. Abb. 78 Autoscale-Funktion: Mehrfachperioden-Wellenformen Horizontal-Vertikal Hinweis: 1. Wenn Sie die Autoscale-Funktion aufrufen, flackert alle 0,5 Sekunden ein A oben links im Bildschirm. 2. Im Autoscale-Modus kann das Oszilloskop den “Triggertyp” (Single und Alternate) sowie den “Modus” (Edge, Video) selbst einschätzen. Zu diesem Zeitpunkt steht das Trigger-Menü nicht zur Verfügung. 3.
Verwenden der integrierten Hilfe 1. Drücken Sie die Help-Taste und der Katalog wrd im Bildschirm angezeigt. 2. Drücken Sie Taste H1 oder H2, um ein Hilfethema auszuwählen, oder wählen Sie es mithilfe des M-Drehknopfes. 3. Durch Drücken der Taste H3 können Sie die Einzelheiten zum jeweiligen Thema anzeigen oder drücken Sie einfach auf den M-Drehknopf. 4. Drücken Sie die Taste H5, um die Hilfe zu verlassen oder zu einer anderen Funktion zu wechseln. 34.
34.2. RUN/STOP: Startet oder stoppt die Wellenformaufnahme. Hinweis: Im Zustand Stop können Sie die vertikale Teilung sowie die horizontale Zeitbasis der Wellenform innerhalb gewisser Grenzen einstellen, d.h. Sie können das Signal in horizontaler oder vertikaler Richtung dehnen. Wenn die horizontale Zeitbasis kleiner order gleich 50 ms ist, kann die horizontale Zeitbasis um 4 Teilungen nach unten ausgeweitet werden. 34.3.
2. Automatische Messung durchführen Das Oszilloskop kann die meisten angezeigten Signale automatisch messen. Gehen Sie wie folgt vor, um Frequenz-, Periode, Mittelwert- und Spitze-Spitze-Werte zu messen: 1. Drücken Sie die Taste Measure, um das Funktionsmenü für die automatische Messung anzuzeigen. 2. Drücken Sie die Taste H1, um das Menü “Hinzufügen” anzuzeigen. 3. Drücken Sie die Taste F2, um CH1 als Quelle auszuwählen. 4. Drücken Sie die Taste F1.
35.2. Beispiel 2: Verstärker-Verstärkung in der zu messenden Schaltung Stellen Sie die Tastkopfdämpfung im Menü auf 10X und mit dem Schalter auf dem Tastkopf ebenfalls auf 10X ein. Verbinden Sie CH1 des Oszilloskops mit dem Signaleingang der Schaltung und CH2 mit dem Ausgang. Bedienung 1. Drücken Sie die Taste AUTOSET; das Oszilloskop nimmt automatisch die richtige Einstellung der beiden Kanäle vor. 2. Drücken Sie die Taste MEASURE, um das Menü MEASURE anzuzeigen. 3. Drücken Sie die Taste H1. 4.
35.3. Beispiel 3: Aufzeichnen eines Einzelsignals Mit dem digitalen Oszilloskop ist es ganz einfach, ein nicht-periodisches Signal wie beispielsweise einen Impuls oder eine Signalspitze usw. aufzuzeichnen. Allerdings stellt sich das allgemeine Problem, wie ein Trigger eingerichtet werden soll, wenn Sie das Signal nicht kennen? Ist z.B. der Impuls ein TTL-Logiksignal, sollten Sie den Triggerpegel auf 2 V einstellen und die Triggerflanke auf die steigende Flanke einstellen.
Abb. 81 Aufzeichnen eines Einzelsignals 35.4. Beispiel 4: Analysieren von Signaldetails Die meisten elektronischen Signale weisen Rauschen auf. Dieses Oszilloskop bietet die sehr wichtige Funktion um zu ermitteln, was sich in dem Rauschen befindet, und den Rauschpegel zu reduzieren. Rauschanalyse Der Rauschpegel weist manchmal auf eine Störung in der elektronischen Schaltung hin. Mithilfe der Spitzenerkennungsfunktion Peak Detect können Sie mehr über dieses Rauschen erfahren.
Abb. 82 Signal mit Rauschen Signal vom Rauschen trennen Bei der Konzentration auf das Signal selbst ist es wichtig, den Rauschpegel so weit wie möglich zu reduzieren, damit der Benutzer mehr Signaldetails erhält. Die Mittelwertfunktion Average dieses Oszilloskops kann Ihnen dabei helfen. So aktivieren Sie die Average-Funktion: 1. Drücken Sie die Acquire-Taste, um das Acquire-Menü aufzurufen. 2. Drücken Sie die Taste H1, um das Menü Acqu Mode anzuzeigen. 3.
35.5. Beispiel 5: Anwendung der X-Y-Funktion Untersuchen der Phasendifferenz zwischen den Signalen beider Kanäle Beispiel: Testen des Phasenwechsels eines Signals nach dem Durchgang durch eine Schaltung. Der X-Y-Modus ist sehr nützlich für das Prüfen der Phasenverschiebung zweier verbundener Signale. Dieses Beispiel zeigt Ihnen Schritt für Schritt, wie Sie den Phasenwechsel des Signals prüfen, nachdem es einen bestimmten Schaltkreis durchlaufen hat.
Auf Grundlage des Ausdrucks sin(q) =A/B oder C/D ist q die Phasenwinkeldifferenz und die Definitionen von A, B, C und D werden im oben gezeigten Schaubild veranschaulicht. Als Ergebnis kann die Phasenwinkeldifferenz ermittelt werden, nämlich q = ± arcsin (A/B ) oder ± arcsin (C/D). Wenn die Hauptachse der Ellipse sich in den Quadranten I und III befindet, sollte sich die ermittelte Phasenwinkeldifferenz in den Quadranten I und IV befinden, d.h. im Bereich (0 ~ π /2) oder (3πc / 2 ~ 2π).
36. Fehlerbehebung 1. Das Oszilloskop ist eingeschaltet, aber keine Anzeige erscheint. * Prüfen Sie, ob der Strom richtig angeschlossen ist. * Prüfen Sie, ob der Netzschalter an der richtigen Position („―“) heruntergedrückt ist. * Prüfen Sie, ob die Sicherung neben der Netzeingangsbuchse nicht durchgebrannt ist (die Abdeckung kann mit einem Schlitzschraubendreher aufgehebelt werden). * Starten Sie das Gerät nach Durchführung der oben genannten Prüfungen erneut.
37. Technische Daten Soweit nicht anders angegeben, gelten die technischen Daten nur für Oszilloskope mit einer eingestellten Tastkopfdämpfung von 10X. Die technischen Daten gelten nur, wenn das Oszilloskop die folgenden beiden Bedingungen erfüllt: mindestens * Das Gerät sollte bei 30 Minuten lang ununterbrochen laufen. * Führen Sie die “Selbstkalibrierung” durch, wenn sich die Betriebstemperatur um bis oder sogar über 5℃ ändert (s. „7. Durchführen der Auto-Kalibrierung“ auf S. 13).
P 1240 P 1245 P 1255 Messraten Bereich P 1260 P 1270 P 1275 Interpolation Dual CH 0.5 S/s ~ 250 MSa/s Single CH 0.5 S/s ~ 500 MSa/s Dual CH 0.5 S/s ~ 500 MSa/s Single CH 0.5 S/s ~ 1 GSa/s Dual CH 0.5 S/s ~ 1 GSa/s Single CH 0.5 S/s ~ 2 GSa/s Dual CH 0.5 S/s ~ 1 GSa/s Single CH 0.5 S/s ~ 2 GSa/s Dual CH 0.5 S/s ~ 1.25 GSa/s Single CH 0.5 S/s ~ 2.5 GSa/s Dual CH 0.5 S/s ~ 1.6 GSa/s Single CH 0.5 S/s ~ 3.
5 ns/div~100 s/div, P 1240 step by 1~2~5 2 ns/div~100 s/div, P 1245 step by 1~2~5 2 ns/div~100 s/div, P 1255 step by 1~2~5 Scan Geschwindigkeit (S/div) 1 ns/div~100 s/div, P 1260 Horizontales step by 1~2~5 1 ns/div~100 s/div, P 1270 System step by 1~2~5 1 ns/div~100 s/div, P 1275 Messrate Sampling / Zeitverzögerungs- genauigkeit Interval (∆T) Genauigkeit (DC~100MHz) step by 1~2~5 ±100ppm Single: ±(1 Zeitintervall +100ppm×Messwert+0.6ns); Durchschnitt>16: ±(1 Zeitintervall +100ppm×Messwert+0.
Cursor ∆V und ∆T zwischen den Cursorn Vpp, Vmax, Vmin, Vtop, Vbase, Vamp, Vavg, Automatische Messfunktionen Messung Vrms, Overshoot, Preshoot, Freq, Period, Rise Time, Fall Time, Delay A→B +Width, -Width, +Duty, -Duty , Delay A→B Mathematische Wellenform +, -, *, / ,FFT Wellenform Speicher 15 Wellenformen Lissajous Band- breite Figur Volle Bandbreite Phasen - ±3 Grad Differenz Frequenz (typisch) 1 kHz Rechtecksignal KommuniUSB 2.
37.2. Allgemeine technische Daten 37.2.1. Anzeige Anzeige-Typ 8” Farb-LCD (Liquid Crystal Display) Anzeige-Auflösung 800 (Horizontal) × 600 (Vertikal) Pixel Anzeige-Farben 65536 Farben, TFT-Bildschirm 37.2.2. Ausgang der Tastkopf-Kompensation Ausgangsspannung (Typisch ) ca. 5 Vss, ≥1 MΩ. Frequenz (Typisch ) Rechteckfrequenz 1 KHz 37.2.3. Spannungsversorgung Spannungsversorgung 100 ~ 240 VACeff , 50/60 Hz, CAT II Leistungsaufnahmen < 18 W Sicherung 1 A T , 250 V Akku (optional) 7.
Reinigung Überprüfen Sie den Zustand von Tastkopf und Gerät in regelmäßigen Abständen. Reinigen Sie die Außenflächen des Geräts wie folgt: 1. Entfernen Sie Staub vom Gerät und vom Tastkopf mit einem weichen Tuch. Vermeiden Sie Kratzer auf der transparenten Schutzscheibe des LCD-Bildschirms, wenn Sie diesen reinigen. 2. Reinigen Sie das Gerät mit einem weichen, feuchten, gut ausgewrungenen Tuch; ziehen Sie dazu zuvor das Netzkabel aus der Steckdose.
Hinweise zur Batterie Abb. 86 Batteriezustandsanzeige Laden des Oszilloskops Schließen Sie das Netzkabel an eine Stromquelle an. Schalten Sie das Gerät mit dem Netzschalter ― ○ auf der linken Geräteseite ein (vergewissern Sie sich, dass die “―”-Seite heruntergedrückt wird). Leuchtet die Batteriezustandsanzeige auf dem Bedienfeld gelb, wird die Batterie aufgeladen. Nach vollständigem Aufladen leuchtet die Anzeige grün.
Gesetzlich vorgeschriebene Hinweise zur Batterieverordnung Im Lieferumfang vieler Geräte befinden sich Batterien, die z. B. zum Betrieb von Fernbedienungen dienen. Auch in den Geräten selbst können Batterien oder Akkus fest eingebaut sein.
Alle Rechte, auch die der Übersetzung, des Nachdruckes und der Vervielfältigung dieser Anleitung oder Teilen daraus, vorbehalten. Reproduktionen jeder Art (Fotokopie, Mikrofilm oder ein anderes Verfahren) nur mit schriftlicher Genehmigung des Herausgebers gestattet. Letzter Stand bei Drucklegung. Technische Änderungen des Gerätes, welche dem Fortschritt dienen, vorbehalten.
1. Safety Precautions This product complies with the requirements of the following European Community Directives: 2004/108/EG (Electromagnetic Compatibility) and 2006/95/EG (Low Voltage) as amended by 2004/22/EG (CE-Marking). Overvoltage category II; pollution degree 2. To ensure safe operation of the equipment and eliminate the danger of serious injury due to short-circuits (arcing), the following safety precautions must be observed.
* Do not store the meter in a place of explosive, inflammable substances. * Do not modify the equipment in any way * Do not place the equipment face-down on any table or work bench to prevent damaging the controls at the front. * Opening the equipment and service – and repair work must only be performed by qualified service personal * Measuring instruments don’t belong to children hands. Cleaning the cabinet Prior to cleaning the cabinet, withdraw the mains plug from the power outlet.
3.
1. 2. 3. 4. 8. 7. 6. 5. Fig. 1 1. Power on/off 2. Display area 3. Power indication light Green light: Indicating Oscilloscope connects with AC Power, and the battery is in full (if there is battery inside Oscilloscope). Yellow light: Indicating Oscilloscope connect with AC Power and the battery is in charging (if there is battery inside Oscilloscope). Dim: Only powered by battery without connecting AC Power. 4. Control (key and knob) area 5.
3.3. Left side panel 1. 2. Fig. 2 Left side panel 1. Power switch:“―” represents power ON; “○” represents power OFF. 2. AC power input jack 3.4. Right side panel 1. 2. 3. 4. Fig. 3 Right side panel 1. USB Host port: It is used to transfer data when external USB equipment connects to the oscilloscope regarded as “Host equipment”. For example: upgrading software by USB flash disk needs to use this port. 2.
3.5. Rear Panel 1. 2. 3. 4. 5. 4. Fig. 4 Rear Panel 1. The port of trigger signal output & Pass/Fail output 2. Handle 3. Air vents 4. Foot stool (can adjust the tilt angle of the oscilloscope) 5.
4. 3.6. Control (key and knob) area 1. 2. 3. 5. 6. 7. 8. Fig. 5 Keys Overview 1. Menu option setting: H1~H5 2. Menu option setting: F1~F5 3. Menu off : turn off the menu 4. M knob(Multipurpose knob) 5. Function key area: Total 12 keys 6. Vertical control area with 3 keys and 4 knobs.
3.7. User interface introduction Fig. 6 Illustrative Drawing of Display Interfaces 1. Waveform Viewing Area. 2. The Trigger State indicates the following information: Auto: The oscilloscope is under the Automatic mode and is collecting the waveform under the non-trigger state. Trig: The oscilloscope has already detected a trigger signal and is collecting the after-triggering information.
16. The frequency of the trigger signal of CH2. 17. It indicates the current function menu. 18/19. It shows the selected trigger type: Rising edge triggering Falling edge triggering Video line synchronous triggering Video field synchronous triggering The reading shows the trigger level value of the corresponding channel. 20. The reading shows the window time base value. 21. The reading shows the setting of main time base. 22. The readings show current sample rate and the record length. 23.
2. Check the Accessories The supplied accessories have been already described in the Appendix B “Accessories” of this Manual. You can check whether there is any loss of accessories with reference to this description. If it is found that there is any accessory lost or damaged, please get in touch with the distributor of Lilliput responsible for this service or the Lilliput’s local offices. 3.
Fig. 7 Auto set Check CH2 by repeating Step 2 and Step 3. 5. How to Implement the Probe Compensation When connect the probe with any input channel for the first time, make this adjustment to match the probe with the input channel. The probe which is not compensated or presents a compensation deviation will result in the measuring error or mistake. For adjusting the probe compensation, please carry out the following steps: 1.
3. Repeat the steps mentioned if necessary. Fig. 9 Adjust Probe 6. How to Set the Probe Attenuation Coefficient The probe has several attenuation coefficients, which will influence the vertical scale factor of the oscilloscope. To change or check the probe attenuation coefficient in the menu of oscilloscope: 1. Press the function menu button of the used channels (CH1 MENU or CH2 MENU). 2. 3. Press H3 button to display the Probe menu; select the proper value corresponding to the probe.
7. How to Implement Self-calibration The self-calibration application can make the oscilloscope reach the optimum condition rapidly to obtain the most accurate measurement value. You can carry out this application program at any time, but when the range of variation of the ambient temperature is up to or over 5 °C, this program must be executed. For the performing of the self-calibration, all probes or wires should be disconnected with the input connector first.
Vertical offset back to 0 shortcut key Turn the VERTICAL POSITION knob to change the vertical display position of channel and press the position knob to set the vertical display position back to 0 as a shortcut key, this is especially helpful when the trace position is far out of the screen and want it to get back to the screen center immediately. 2. Change the Vertical Setting and Observe the Consequent State Information Change.
2. Use the “HORIZONTAL POSITION” knob to adjust the horizontal position of the signal in the waveform window. The “HORIZONTAL POSITION” knob is used to control the triggering displacement of the signal or for other special applications. If it is applied to triggering the displacement, it can be observed that the waveform moves horizontally with the knob when you rotate the “HORIZONTAL POSITION” knob.
4. Press the “Force” button to force a trigger signal, which is mainly applied to the “Normal” and “Single” trigger modes. 11. How to Set the Vertical System The VERTICAL CONTROLS includes three menu buttons such as CH1 MENU, CH2 MENU and Math, and four knobs such as VERTICAL POSITION, VOLTS/DIV (one group for each of the two channels). Setting of CH1 and CH2 Every channel has an independent vertical menu and each item is set respectively based on the channel. 11.1.
The description of the Channel Menu is shown as the following list: Function Menu Coupling Inverted Setting Description DC Unblock the AC and DC components in the input signal. AC Block the DC component in the input signal. GROUND The Input signal is interrupted. OFF The waveform is displayed normally. ON Initiate the waveform inverted function. 1X Probe 10X Choose one according to the probe attenuation factor to 100X make the vertical scale reading accurate.
11.3. Regulate the probe attenuation. In order to match the attenuation coefficient of the probe, it is required to adjust the attenuation ration coefficient of the probe through the operating menu of the Channel accordingly (see “6. How to set the Probe Attenation Coefficient” on page 100). If the attenuation coefficient of the probe is 1:1, that of the oscilloscope input channel should also be set to X1 to avoid any errors presented in the displayed scale factor information and the measured data.
11.4. Setting of Waveform Inverted Waveform inverted: the displayed signal is turned 180 degrees against the phase of the earth potential. Taking the Channel 1 for example, the operation steps are shown as follows: 1. Press the CH1 MENU button and get access to the CH1 SETUP menu. 2. Press the H2 menu selection button and select ON for Inverted item. The waveform inverted function is initiated. 3. Press the H2 menu selection button again and select OFF for Inverted item.
11.5. Setting of Band Limit (only P 1245/1255/1260) When high frequency components of a waveform are not important to its analysis, the bandwidth limit control can be used to reject frequencies above 20 MHz. Taking the Channel 1 for example, the operation steps are shown as below: 1. Press the CH1 MENU button to call out the CH1 SETUP menu. 2. Press the H4 button and the Limit menu will display. 3. Press the F1 button to select the Band Limit as full band.
The corresponding FCL (Functional Capabilities List) of the Waveform Calculation: Function Menu Setting Factor1 Dual Wfm Math Sign Factor 2 Source CH1 CH2 +-*/ CH1 CH2 Description Select the signal source of the factor1 Select the sign of mathematical manipulation Select the signal source of the factor2 CH1 Select CH1 as FFT source. CH2 Select CH2 as FFT source. Rectangle Window Blackman Hanning Select window for FFT. Hamming FFT Format Zoom dB Select dB for Format.
13. Using FFT function The FFT (fast Fourier transform) math function mathematically converts a time-domain waveform into its frequency components. It is very useful for analyzing the input signal on Oscilloscope. You can match these frequencies with known system frequencies, such as system clocks, oscillators, or power supplies.
This is a very good window for resolving frequencies that are very close to the same value with somewhat improved amplitude accuracy over the rectangle window. It has a slightly better frequency resolution than the Hamming Hanning. Use Hamming for measuring sine, periodic and narrow band random noise. This window works on transients or bursts where the signal levels before and after the event are significantly different.
Fig. 22 Hamming window Fig. 23 Hanning window Fig.
13.2. Notes for using FFT * If desired, use the zoom feature to magnify the FFT waveform. * Use the default dB scale to see a detailed view of multiple frequencies, even if they have very different amplitudes. Use the Vrms scale to see an overall view of how all frequencies compare to each other. * Signals that have a DC component or offset can cause incorrect FFT waveform component magnitude values. To minimize the DC component, choose AC Coupling on the source signal.
Fig. 25 Information about Vertical Position 15. How to Set the Horizontal System The HORIZONTAL CONTROLS includes the HORIZ MENU button and such knobs as HORIZONTAL POSITION and SEC/DIV. 1. HORIZONTAL POSITION knob: this knob is used to adjust the horizontal positions of all channels (include those obtained from the mathematical manipulation), the analytic resolution of which changes with the time base. 2.
16. Main Time Base Press the H1 menu selection button and choose Main. In this case, the HORIZONTAL POSITION and SEC/DIV knobs are used to adjust the main window. The display in the screen is shown as Fig. 27. Fig. 27 Main Time Base 17. Set Window Press the H2 menu selection button and choose Set. The screen will show a window area defined by two cursors. In this case, the HORIZONTAL POSITION and SEC/DIV knobs can be used to adjust the horizontal position and size of this window area.
18. Window Expansion Press the H3 menu selection button and choose Zoom. As a result, the window area defined by two cursors will be expanded to the full screen size (see Fig. 29). Fig. 29 Zoom Window 19. How to set the Trigger System Trigger determines when Oscilloscope starts to acquire data and waveform display. Once trigger to be set correctly then it will convert the unstable display to meaning waveform.
19.1. Trigger Control The oscilloscope provides two trigger types: single trigger and alternate trigger. Single trigger: Use a trigger level to capture stable waveforms in two channels simultaneously. Alternate trigger: Trigger on non-synchronized signals. The Single Trigger and Alternate Trigger menus are described respectively as follows: Single trigger Single trigger has four modes: edge trigger, video trigger, slope trigger and pulse trigger.
Edge menu list: MENU SETTINGS INSTRUCTION Single Mode Edge Set vertical channel trigger type as edge trigger. CH1 Select CH1 as trigger signal. CH2 Select CH2 as trigger signal. EXT Select Ext-trigger as trigger signal EXT/5 Select attenuated Ext TRIG/5 as trigger signal. AC Line Select power line as trigger signal. AC Not allow DC portion to pass. DC Allow all portion pass. HF Not allow high frequency of signal pass and only low frequency portion Source Coupling pass.
Sync Line Synchronic trigger in video line Field Synchronic trigger in video field Odd Synchronic trigger in video odd filed Even Synchronic trigger in video even field Line NO. Synchronic trigger in designed video line, turn the M knob to set the line number Mode Holdoff Auto Acquire waveform even no trigger occurred Holdoff 100ns~10s, adjust the M knob to set time interval before another trigger occur Reset Set Holdoff time as 100ns 3.
4. Pulse Width Trigger Pulse trigger occurs according to the width of pulse. The abnormal signals can be detected through setting up the pulse width condition. The Pulse Width Trigger Menu is shown as Fig. 33. Fig. 33 Pulse Width Trigger menu Pulse Width Trigger menu list MENU SETTING INSTRUCTION Single Mode Pulse Set vertical channel trigger type as pulse trigger. CH1 Select CH1 as the trigger source. CH2 Select CH2 as the trigger source. AC Not allow DC portion to pass.
6. Alternate trigger (Trigger mode: Edge) Alternate trigger (Trigger Type: Edge) Menu is shown as Fig. 34. Fig. 34 Alternate trigger (Trigger Type: Edge) Menu Alternate trigger (Trigger Type: Edge) Menu list: MENU SETTING INSTRUCTION Alternate Mode Edge Set vertical channel trigger type as edge trigger. CH1 Select CH1 as the trigger source. CH2 Select CH2 as the trigger source. AC Not allow DC portion to pass. DC Allow all portion pass.
Alternate trigger (Trigger Type: video) Menu list: MENU SETTING INSTRUCTION Alternate Mode Video Set vertical channel trigger type as video trigger. CH1 Select CH1 as the trigger source. CH2 Select CH2 as the trigger source. Source NTSC Modu PAL Select video modulation SECAM Sync Line Synchronic trigger in video line. Field Synchronic trigger in video field. Odd Field Synchronic trigger in video odd filed Even Field Synchronic trigger in video even field Line NO.
9. Alternate trigger (Trigger Mode: Pulse) Alternate trigger (Trigger Type: Pulse) Menu is shown as Fig. 37. Fig. 37 Alternate trigger (Trigger Type: Pulse) Menu Alternate trigger (Trigger Type: Pulse) menu list: MENU Alternate Mode Source Coupling SETTING INSTRUCTION Pulse Set vertical channel trigger type as pulse trigger. CH1 Select CH1 as the trigger source. CH2 Select CH2 as the trigger source. AC Not allow DC portion to pass. DC Allow all portion pass.
* AC Line: AC power can be used to display signals related to the power line frequency, such as lighting equipment and power supply devices. The oscilloscope gets triggered on its power cord, so you do not have to input an AC trigger signal. When AC Line is selected as trigger source, the oscilloscope automatically set coupling to DC, set trigger level to 0V. 2. Trigger Mode: The trigger mode determines how the oscilloscope behaves in the absence of a trigger event.
20. How to Implement Sampling Setup Press the Acquire button and the menu is displayed in the screen, shown as Fig. 38. Fig. 38 ACQU MODE Menu The description of the Acqu Mode Menu is shown as follows: Function Menu Setting Sample Description General sampling mode. Use to capture maximal and minimal samples. Finding highest and lowest points over adjacent intervals. It is used for the Peak detect detection of the jamming burr and the possibility of reducing the Sample confusion.
Fig. 39 Peak Detect mode, under which the burrs on the falling edge of the square wave, can be detected and the noise is heavy. Fig. 40 Common ACQU Mode display, in which no burr can be detected. Fig. 41 The displayed waveform after the noise is removed under the Average Mode, in which the average number of 16 is set.
21. How to Set the Display System Push down the Display button and the menu displayed in the screen is shown as Fig. 42. Fig. 42 Display Set Menu The description of the Display Set Menu is shown as follows: Function Menu Type Setting Description Dots Only the sampling points are displayed. Vect The space between the adjacent sampling points in the display is filled with the vector form.
Fig. 44 Display in Dots form 22. Persist When the Persist function is used, the persistence display effect of the picture tube oscilloscope can be simulated. The reserved original data is displayed in fade color and the new data is in bright color. Press the H2 button, the Persist menu will display at the right of screen. Press the F1 button, different persistence time can be chosen: OFF, 1second, 2second, 5second and Infinity.
23. XY Format This format is only applicable to Channel 1 and Channel 2. After the XY display format is selected, Channel 1 is displayed in the horizontal axis and Channel 2 in the vertical axis; the oscilloscope is set in the un-triggered sample mode: the data are displayed as bright spots. The operations of all control knobs are as follows: * The Vertical VOLTS/DIV and the VERTICAL POSITION knobs of Channel 1 are used to set the horizontal scale and position.
24. Cymometer It is a 6-digit cymometer. The cymometer can measure frequencies from 2Hz to the full bandwidth. Only if the measured channel has triggering signal and in Edge mode, it can measure frequency correctly. In the Single trigger mode, it is a one channel cymometer and it can only measure the frequency of the triggering channel. In the ALT trigger mode, it is a two channel cymometer and it can measure the frequency of two channels. The cymometer is displayed at the right bottom of the screen.
The description of the Save Function Menu is shown as the following table: Function Menu Setting Wave Setting Type Image Record Description Choose the saving type (the Record Type see “27.1. How to Record/Playback Waveforms” on page 134). When the type is Wave, the menu shows as following: CH1 Source CH2 Choose the waveform to be saved. Math Object 1~15 Choose the address which the waveform is saved to or recall from. Recall or close the waveform stored in the current object address.
27. Save and Recall the Waveform This oscilloscope can store 15 waveforms, which can be displayed with the current waveform at the same time. The stored waveform called out cannot be adjusted. In order to save the waveform of the CH1 into the address 1, the operation steps should be followed: 1. Saving: Press the H1 button, the Type menu will display at the left of screen, turn the M knob to choose Wave for Type. 2. Press the H2 button and press F1 button to select CH1 for Source. 3.
2. After the USB disk is installed, press the Save panel button, the save menu is displayed at the bottom of the screen. 3. Press the H1 button, the Type menu will display at the left of screen, turn the M knob to choose Image for Type. 4. Press the H4 button, the input keyboard used to edit the file name will pop up. The default name is current system date. Turn the M knob to choose the keys; press the M knob to input the chosen key. The length of file name is up to 25 characters.
Record menu shows as follows: Menu Mode Setting Instruction OFF Close wave record function Record Set record menu Playback Set playback menu Storage Set storage menu End frame Turn the M knob to select the number of frames to record (1 ~ 1000) Record mode FrameSet Refresh Operate Interval Turn the M knob to select the interval between recorded frames (1 ms ~ 1000 s) ON Refresh wave during recording OFF Stop refreshing Play Begin to record Stop Stop recording Note: Both of the wavef
Playback: Play back the wave recorded or saved.
Fig. 52 Wave Storage To use wave record function, do as follows: 1. Press Save button. 2. Press H1 button, turn the M knob to choose Record. 3. Press H2 button. In the Mode menu, press F2 button to choose Record. 4. Press H3 button. In the Frame Set menu, press F1 button and turn the M knob to set End frame; press F2 button and turn the M knob to select the interval between recorded frames. 5. Press H4 button, choose whether to refresh the wave when recording. 6.
The description of Configuration Menu is shown as the follows: Function Menu Setting Description Chinese language English Choose the display language of the operating system. Others On Display Set Time Hour Off Min Day Month Year KeyLock About On/Off the date display Setting Hour/Minute Setting Date/Month Setting Year Lock all keys. Unlock method: press 50% button in trigger control area, then press Force button, repeat 3 times. Version number and serial number showing 27.2.2.
The description of Adjust Menu is shown as the follows: Function Menu Setting Description Self Cal Carry out the self-calibration procedure. Default Call out the factory settings. Do Self Cal (Self-Calibration) The self-calibration procedure can improve the accuracy of the oscilloscope under the ambient temperature to the greatest extent. If the change of the ambient temperature is up to or exceeds 5°C, the self-calibration procedure should be executed to obtain the highest level of accuracy.
Function Menu operate Output Setting Description Enable Control enable switch Operate Control operate switch Pass Signal tested corresponds with the rule Fail Signal tested not correspond with the rule Beep Beep when it satisfies the rule Stop Stop once satisfying the rule Info Control the display status of info frame Source Select source CH1, CH2 or Math Horizontal Rule Vertical SaveRule Change the Horizontal tolerance value by turning the M knob Change the Vertical tolerance value
Fig. 58 Pass/Fail test Note: 1. When Pass/Fail is ON, if XY or FFT is ready to run, then Pass/Fail will be closed; under the mode of XY or FFT, Pass/Fail is unable. 2. Under the mode of Factory, Auto Scale and Auto Set, Pass/Fail will be closed. 3. When no save setting left in the rule save, tip will be given to show “NO RULE SAVED”. 4. Under the status of stop, data comparing will stop, and when it goes on running, the number of Pass/Fail will increase from the former number, not from zero. 5.
27.2.6. LAN Set Using the LAN port, the oscilloscope can be connected with a computer directly, or through the router to connect. The network parameters can be set in the menu below. Press the Utility button and turn the M knob to select the LAN Set to go to the following menu. Fig.
Fig. 61 ® Set the network parameters of the PeakTech Oscilloscope Software. Run the software on the computer, choose the “Ports-settings” of the “Communications” menu item. Set “Connect using” to LAN. About the IP, the first three bytes is same as the IP in the step (2), the last byte should be different. Here, we set it to 192.168.1.72. The range of the port value is 0 ~ 4000, but the port which under 2000 is always be used, so it is suggested to set it to the value above 2000. Here, we set it to 3000.
Set the network parameters of the oscilloscope. In the oscilloscope, press the Utility button and press H1 button, turn the M knob to select the LAN Set; press the H2 button, the set menu is displayed on the right. Set the IP and the Port to the same value as the “Ports-settings” in the software in step (3). Press the F5 button, it prompts “reset to update the config”. After resetting the oscilloscope, if you can get data normally in the oscilloscope software, the connection is successful. Fig.
Fig. 64 ® Set the network parameters of the PeakTech Oscilloscope Software. Run the software on the computer; choose the “Ports-settings” of the “Communications” menu item. Set “Connect using” to LAN. About the IP, the first three bytes is same as the IP in the step (2), the last byte should be different. Here, we set it to 192.168.1.72. The range of the port value is 0 ~ 4000, but the port which under 2000 is always be used, so it is suggested to set it to the value above 2000. Here, we set it to 3000.
Set the network parameters of the oscilloscope. In the oscilloscope, press the Utility button and press H1 button, turn the M knob to select the LAN Set; press the H2 button, the set menu is displayed on the right. Set the IP and the Port to the same value as the “Ports-settings” in the software in step (3). The Netgate should be set according to the router. Press the F5 button, it prompts “reset to update the config”.
28. How to Measure Automatically Press the Measure button to display the menu for the settings of the Automatic Measurements. The oscilloscopes provide 20 parameters for auto measurement, including Vpp, Vmax, Vmin, Vtop, Vbase, Vamp, Vavg, Vrms, Overshoot, Preshoot, Freq, Period, Rise Time, Fall Time, Delay A→B A→B ,+Width, -Width, +Duty, -Duty. That’s 10 voltage and 10 time measurements in all. , Delay The menu is displayed as Fig. 67. Fig.
29. Measure The measured values can be detected on each channel simultaneously. Only if the waveform channel is in the ON state, the measurement can be performed. The automatic measurement cannot be performed in the following situation: 1) On the saved waveform. 2) On the mathematical waveform. 3) On the XY format. 4) On the Scan format. Measure the frequency, the peak-to-peak voltage of the Channel CH1 and the mean, the RMS of the Channel CH2, following below steps: 1.
30. The automatic measurement of voltage parameters The oscilloscopes provide automatic voltage measurements including Vpp, Vmax, Vmin, Vavg, Vamp, Vrms, Vtop, Vbase, Overshoot and Preshoot. Fig. 69 below shows a pulse with some of the voltage measurement points. Fig. 69 Vpp: Peak-to-Peak Voltage. Vmax: The maximum amplitude. The most positive peak voltage measured over the entire waveform. Vmin: The minimum amplitude. The most negative peak voltage measured over the entire waveform.
30.1. The automatic measurement of time parameters The oscilloscopes provide time parameters auto-measurements include Frequency, Period, Rise Time, Fall Time, +Width, -Width, Delay 1→2 , Delay 1→2 , +Duty and -Duty. Fig. 70 shows a pulse with some of the time measurement points. Fig. 70 Rise Time: Time that the leading edge of the first pulse in the waveform takes to rise from 10% to 90% of its amplitude.
The description of the cursor measurement menu is shown as the following table: Function Menu Type Source Setting Description OFF Switch off the cursor measurement. Voltage Display the voltage measurement cursor and menu. Time Display the time measurement cursor and menu. CH1 Display the channel generating the waveform to which the cursor CH2 measurement will be applied.
Carry out the following operation steps for the time cursor measurement of the channel CH1: 1. Press Cursor and recall the Cursor Measure menu. 2. Press the H2 button and choose CH1 for Source. 3. Press the H1 button, the Type menu will display at the right of the screen. Press the F3 button to select Time for Type, with two purple dotted lines displayed along the vertical direction of the screen, which indicating Cursor 1 and Cursor 2. 4.
32. The Cursor Measurement for FFT model Press the Cursor button to display the cursor measurement function menu (CURS MEAS) in the screen, which includes Vamp Measurement and Freq Measurement at the mode of FFT, shown as Fig. 74. Fig. 74 CURS MEAS Menu The description of the cursor measurement menu is shown as the following table: Function Menu Type Source Setting Description OFF Switch off the cursor measurement. Vamp Display the Vamp measurement cursor and menu.
Fig. 75 wave of Vamp cursor measurement Carry out the following operation steps for the Freq cursor measurement: 1. Press Cursor and recall the Cursor Measure menu. 2. Press the H1 button, the Type menu will display at the right of the screen. Press the F3 button to select Freq for Type, with two purple dotted lines displayed along the vertical direction of the screen indicating the corresponding Cursor 1 and Cursor 2. 3.
33. How to use Autoscale The function is applied to follow-up signals automatically even if the signals change at any time. Autoscale enables the instrument to set up trigger mode, voltage division and time scale automatically according to the type, amplitude and frequency of the signals. Fig. 77 Autoscale menu The menu is as follows: Function Menu Autoscale Setting Instruction ON Turn on Autoscale. OFF Turn off Autoscale. Follow-up and adjust the vertical and horizontal settings.
Then the wave is displayed in the screen, shown as Fig. 78. Fig. 78 Autoscale Horizontal- Vertical multi-period waveforms Note: 1. Entering into Autoscale function and the A flicker will be at the top left of the screen. (flicker every 0.5 second) 2. In the mode of Autoscale, the oscilloscope can self-estimate “Trigger Type” (Single, and Alternate) and “Mode” (Edge, Video). At this point, the trigger menu is not available. 3.
34. How to Use Executive Buttons Executive Buttons include Autoset, Run/Stop, Single, Copy. 34.1. Autoset This button is used for the automatic setting of all control values of the instrument to generate the waveform suitable for observation. Press the Autoset button and the oscilloscope will perform the fast automatic measurement of the signal.
34.4. Copy This button is the shortcut of saving function of the Save function menu. Pressing this button is equal to the Save option in the Save function menu. The current waveform or the display creen could be saved according to the setting of the Save function menu. For more details, please see “Save Function Menu” on page 132 35. Demonstration 35.1.
Fig. 79 Waveform of Automation Measurement 35.2. Example 2 Gain of the Amplifier in the Metering Circuit Set the probe menu attenuation coefficient as 10X and that of the switch in the probe as 10X (see “6. How to the Probe Attenuation Coefficient” on page 101). Connect the oscilloscope CH1 channel with the circuit signal input end and the CH2 channel to the output end. Operation Steps: 1.
Fig. 80 Waveform of Gain Measurement 35.3. Example 3: Capture the Single Signal The digital storage oscilloscope takes the lead in providing the convenience capturing of such non-periodic signals as pulse and burr, etc. If you intent to capture a single signal, you can not set the trigger level and the trigger edge unless you have particular priori knowledge of this signal.
15. If the Trigger State Indicator at the top of the screen does not indicate Ready, push down the Run/Stop button and start acquiring, waiting the emergence of the signal in conformity with the trigger conditions. If a signal reaches to the set trigger level, one sampling will be made and then displayed in the screen. With this function, any random occurrence can be captured easily.
Fig. 82 Waveform of the Signal Containing Noises Separate Noises from the Signal When analyze the waveform of a signal, you should remove the noise in it. For the reduction of the random noise in the oscilloscope display, please operate the instrument according to the following steps: 1. Press the Acquire button to display the Acquire menu. 2. Press the H1 button to display ACQU Mode menu. 3.
35.5. Example 5: Application of X-Y Function Examine the Phase Difference between Signals of two Channels Example: Test the phase change of the signal after it passes through a circuit network. Connect the oscilloscope with the circuit and monitor the input and output signals of the circuit. For the examination of the input and output of the circuit in the form of X-Y coordinate graph, please operate according to the following steps: 1.
35.6. Example 6: Video Signal Trigger Observe the video circuit of a television, apply the video trigger and obtain the stable video output signal display. Video Field Trigger For the trigger in the video field, carry out operations according to the following steps: 1. Press the Trigger Menu button to display the trigger menu. 2. Press the H1 button to display the trigger type menu. 3. Press the F1 button to choose Single for Type. 4. Turn the M knob to choose Video as the mode. 5.
36. Troubleshooting 1. Oscilloscope is powered on but no Display. * Check whether the power connection is connected properly. * Check whether the power switch is pushed down to the designated position. * Check whether the fuse which is beside the AC power input jack is blew (the cover can be pried open with a straight screwdriver). 2. * Restart the instrument after completing the checks above. * If the problem persists, please contact Lilliput and we will be under your service.
37. Technical Specifications Unless otherwise specified, the technical specifications applied are applicable to the probe with the attenuation switch setting 10X and this digital oscilloscope. Only if the oscilloscope fulfills the following two conditions at first, can these specification standards be reached. * This instrument should run for more than 30 minutes continuously under the specified operating temperature.
P 1240 P 1245 P 1255 Sampling rate range P 1260 P 1270 P 1275 Interpolation Dual CH 0.5 Sa/s ~ 250 MSa/s Single CH 0.5 Sa/s ~ 500 MSa/s Dual CH 0.5 Sa/s ~ 500 MSa/s Single CH 0.5 Sa/s ~ 1 GSa/s Dual CH 0.5 Sa/s ~ 1 GSa/s Single CH 0.5 Sa/s ~ 2 GSa/s Dual CH 0.5 Sa/s ~ 1 GSa/s Single CH 0.5 Sa/s ~ 2 GSa/s Dual CH 0.5 Sa/s ~ 1.25 GSa/s Single CH 0.5 Sa/s ~ 2.5 GSa/s Dual CH 0.5 Sa/s ~ 1.6 GSa/s Single CH 0.5 Sa/s ~ 3.
P 1240 P 1245 Scanning speed (S/div) Horizontal P 1255 P 1260 P 1270 System P 1275 Sampling rate / relay time accuracy Interval( T) Accuracy (DC~100MHz) 5 ns/div ~ 100 s/div, step by 1 ~ 2 ~ 5 2 ns/div ~ 100 s/div, step by 1 ~ 2 ~ 5 1 ns/div ~ 100 s/div, step by 1 ~ 2 ~ 5 1 ns/div ~ 100 s/div, Step by 1 ~ 2 ~ 5 1 ns/div ~ 100 s/div, Step by 1 ~ 2 ~ 5 1 ns/div ~ 100 s/div, Step by 1 ~ 2 ~ 5 ±100 ppm Single: ±(1 interval time+100 ppm×reading+0.6 ns); Average>16: ±(1 interval time +100 ppm×reading+0.
Cursor V and T between cursors Vpp, Vmax, Vmin, Vtop, Vbase, Vamp, Vavg, Vrms, Overshoot, Preshoot, Freq, Period, Rise Time, Fall Automatic Measurement Time, Delay A→B +Duty, -Duty Waveform Math +, -, *, / ,FFT Waveform storage 15 waveforms Lissajous figure Bandwidth Phase difference Frequency ( typical) Communication port * , DelayA→B , +Width, -Width, Full bandwidth ±3 degrees 1 kHz square wave USB 2.
37.2. General Technical Specifications 37.2.1. Display Display Type 8” Colored LCD (Liquid Crystal Display) Display Resolution 800 (Horizontal) × 600 (Vertical) Pixels Display Colors 65536 colors, TFT screen 37.2.2. Output of the Probe Compensator Output Voltage (Typical ) About 5 V, with the Peak-to-Peak voltage equal to or greater than 1 MΩ of load. Frequency (Typical ) Square wave of 1 KHz 37.2.3.
38.2. Appendix B: Maintenance, Cleaning and Repairing General Maintenance Please don't store or put the instrument in the place where the liquid crystal display will be directly exposed to the sunlight for a long time. Caution: The instrument or probe should not be stained with the spraying agent, liquid and solvent to avoid any damage to it. Cleaning Check the probe and instrument regularly according to their operating state. Clean the external surface of the instrument following the steps shown below: 1.
38.4. Charging the oscilloscope Connect the power cord to a power source. Turn on the Power Switch Button ― ○ on the left side (make sure the “―” side is pressed down). Yellow light of the indicator on the front panel means the battery is being charged. Once the battery is full, the indicator will become green. The lithium battery maybe not be charged when delivery. Please charge the battery for 12 hours to make sure enough power to supply to oscilloscope.
All rights, also for translation, reprinting and copy of this manual or parts are reserved. Reproduction of all kinds (photocopy, microfilm or other) only by written permission of the publisher. This manual considers the latest technical knowing. Technical changings which are in the interest of progress reserved. We herewith confirm, that the units are calibrated by the factory according to the specifications as per the technical specifications. We recommend to calibrate the unit again, after one year.