PeakTech ® 2755 Bedienungsanleitung / Operation Manual Installationstester Installation Safety Tester
Thema 1. Einleitung 2. Sicherheitshinweise 2.1. Sicherheitssysmbole am Gerät 2.2. Erfüllte Normen 3. Technische Merkmale 3.1. Gerätespezifikationen 3.2. Begriffserklärung 4. Vorbereitung 4.1. Funktionstasten 4.2. Anschlüsse 4.3. Akku/Batterien und Sicherungen 4.4. Anzeige / Symbole 5. Bedienung 5.1. Wichtige Symbole während der Messung 5.1.1 Symbole und Meldungen in der Spannungsfunktion 5.1.2. Symbole und Meldungen in der LOOP/PFC Funktion 5.1.3 Symbole und Meldungen in der FI (RCD) Funktion 5.1.
Issue 1. Introduction 2. Safety Precautions 2.1. Safety Symbols 2.2. Used standards 3. Specifications 3.1 General Specifications 3.2. Explanation of therms 4. Control 4.1. Function keys 4.2. Connections 4.3. Batteries and Fuses 4.4. Display / Symbols 5. How to use the Tester 5.1. Important symbols and messages during the measurement 5.1.1 Displayed icons (symbols) and messages in VOLTAGE function 5.1.2. Displayed icons (symbols) and messages in LOOP/PFC function 5.1.3.
1. Einleitung Dieses Gerät erfüllt die EU-Bestimmungen 2004/108/EG (elektromagnetische Kompabilität) und 2006/95/EG (Niederspannung) entsprechend der Festlegung im Nachtrag 2004/22/EG (CEZeichen). Überspannungskategorie CAT III 600V Verschmutzungsgrad 2. 2. Sicherheitshinweise Zur Betriebssicherheit des Gerätes und zur Vermeidung von schweren Verletzungen durch Stromoder Spannungsüberschläge bzw. Kurzschlüssen sind nachfolgend aufgeführte Sicherheitshinweise zum Betrieb des Gerätes unbedingt zu beachten.
2.1. Sicherheitssysmbole am Gerät Achtung! Stromschlaggefahr! Öffnen Sie nicht das Gehäuse während eines Messvorganges! Achtung! Keine Überspannung an die Eingangsbuchsen anlegen! Entfernen Sie die Prüfleitungen vor dem Öffnen des Batteriefachs! Reinigung – Benutzen Sie nur trockene Tücher zum Reinigen des Gehäuses! Beachten Sie alle Sicherheitshinweise aus der Bedienungsanleitung! Erdung Doppelte Isolierung Sicherung Nicht an elektrischen Anlagen über 550V verwenden TÜV/GS-geprüft; TÜV Rheinland 2.2.
3. Technische Merkmale Schleifenwiderstand L-PE (Hi-Amp) Bereich (Ω) Auflösung(Ω) Genauigkeit 0.23 – 9.99 0.01 ±(4% v.M.+ 6 Stellen) 10.0 – 99.9 0.1 100 – 999 1 Prüfstrom ………..…………….………………………………………………… 4.0 A Spannungsbereich …………………………………195 V AC. – 260 V AC (50,60Hz) L- PE (Kein Auslösen) Bereich (Ω) Auflösung(Ω) Genauigkeit 0.23 – 9.99 0.01 ±(5% v.M.+ 6 Stellen) 10.0 – 99.9 0.1 100 – 999 1 Prüfstrom ……………………..………………………………………………… < 15mA Spannungsbereich …….
Genauigkeit beim angegebenen Prüfstrom Prüfstrom Genauigkeit x1/2 ±(1% + 1 ms) x1 ±(1% + 1 ms) x2 ±(1% + 1 ms) X5 ±(1% + 1 ms) Form des Prüfstroms Sinuswellenform (AC) Pulswellenform (DC) General (G - nicht verzögert), Selektive (S - zeitverzögert) 0 °, 180 ° 195 V AC – 260 V AC (50Hz, 60Hz) ± (10% + 1 St.
Isolationswiderstand (Isolation) PrüfMessbereich Auflösung Genauigkeit Prüfstrom Kurzschlußstrom spannung 0.125~4.000 MΩ 0.001MΩ ±2% + 10St. 4.001~40.00 MΩ 0.01MΩ 125V (0%~+10%) 40.01~400.0 MΩ 0.1MΩ 400.1~1000 MΩ 1MΩ 0.250~4.000 MΩ 0.001MΩ 4.001~40.00 MΩ 0.01MΩ 250V (0%~+10%) 40.01~400.0 MΩ 0.1MΩ 400.1~1000 MΩ 1MΩ 0.500~4.000 MΩ 0.001MΩ 4.001~40.00 MΩ 0.01MΩ 500V (0%~+10%) 40.01~400.0 MΩ 0.1MΩ 400.1~1000 MΩ 1MΩ 1.000~4.000 MΩ 0.001MΩ 4.001~40.00 MΩ 0.01MΩ 1000V (0%~+10%) 40.01~400.0 MΩ 0.1MΩ 400.
3.1. Gerätespezifikationen Stromversorgung Batteriebetriebsdauer Überspannungskategorie Schutzklasse Schutzart LCD- Anzeige Betriebstemperatur Relative Luftfeuchtigkeit Lagertemperatur Betriebshöhe Schutzeinrichtung Abmessungen Gewicht 3.2. Begriffserklärung Funktion Submenü RCD AUTO RCD TIME RCD RAMP Trip Current Type of RCD RCD (FI-Test) 0°/180° UF UL 12 V DC 8x 1,2V Ni-Mh Akkus (2500mAh) oder eqivalent ca.
LOOP PFC LOOP/PFC (Schleifenimpedanz) PSC Current No Trip Current Hi Amp Zero V (Spannungsmessung) V/Phase Die Schleifenimpedanz gibt die Summe aller Widerstandskomponenten einer Stromschleife an, welche in einem Fehler vom Fehlerstrom durchflossen wird. Dieser Widerstand muss möglichst gering sein bis die Schutzmaßnahmen ausgelöst haben und den Stromkreis unterbrechen, damit bei hohen Fehlerströmen keine Hitze in den Leitungen entsteht, wodurch ein Brand entstehen kann.
Continuity (Durchgang) Low Ohm mA (Prüfstrom) Beeper Zero Erdungswiderstand (RE) RE Zero Isolationswiderstand Terminal Voltage Insulation Beeper Lock Reference Eine Durchgangsprüfung dient zur Überprüfung von intakten Verbindungen in einem nicht aktiven Stromkreis. Sind alle Klemmen korrekt angeschlossen, sollte der Widerstand möglichst gering sein.
4. Vorbereitung 4.1. Funktionstasten 6 Nummer 1 2 3 4 5 6 7 8 3 2 1 4 5 8 7 Beschreibung Startet den ausgewählten Test. Die Test-Taste wird durch ein "Touch-Pad" umgeben. Das Touchpad erfasst das Potential zwischen dem Anwender und der PE-Klemme. Wenn Sie eine 100-V-Schwelle überschreiten, wird das Warnsymbol am Touchpad beleuchtet. Warnleuchte 320 x 240 Pixel Farbdisplay Drücken und halten Sie den Tester zum Ein- und Ausschalten. Kurzes Drücken zeigt aktuellen Status.
4.2.
4.3.
4.4. Anzeige / Symbole Nummer Funktion / Symbol Wert / Bedeutung AUTO x½ x1 RCD (FI-Test) x2 x5 RAMP L-PE L-L L-N Loop/PFC (Schleifenimpedanz) 1 V/Phase (Spannung / Phasendrehung) L-PE 0.5 1.0 2.0 5.0 10.0 20.0 50.
Nummer Funktion / Symbol Wert / Bedeutung 30mA 100mA 300mA 500mA 650mA 1000mA 10mA NO Trip Hi Amp OFF ON Trip Current (Auslösestrom) 2 Current (Auslöseverhalten) Beeper (Summer) Normaler FI- sinusförmiger Prüfstrom 3 Type of RCD (Art des FI) Selektiver FI- sinusförmiger Prüfstrom Normaler FI- Halbwelle-Prüfstrom Lock (Sperre) 0°/180° Selektiver FI- Halbwelle-Prüfstrom OFF ON 0° 180° ZERO (Nullung) 4 Referenz 5 Datum / Uhrzeit 0.125MΩ 0.25MΩ 0.
Nummer Funktion / Symbol Wert / Bedeutung 7 Summer 8 Sperre für fortlaufende Prüfung aktiv 9 Haltefunktion 10 Datenlogger 11 Bluetooth Verbindung aktiviert 12 Wird bei Überhitzung angezeigt 13 Anzeige bei zeitverzögerten FIs (30 Sekunden) 14 Test wird aktuell ausgeführt Primäre Anzeige mit aktuellem Messwert 15 16 Einheit des aktuellen Messwertes Primäre Anzeige mit aktuellem Messwert 17 18 Einheit des aktuellen Messwertes 19 20 21 Fehlerspannung Zeigt das aktuelle Limit für die Fehlers
Nummer 22 23 24 Funktion / Symbol N-PE L-N L-PE PFC 25 PSC Wert / Bedeutung N-PE Wert (Neutralleiter zu Erdung) L-N Wert (Phase zu Neutralleiter) L-PE Wert (Phase zu Erdung) Erdschlussstrom. Berechnet die Spannung und Schleifenimpedanz, die von Phase zu Schutzleiter gemessen wird. Voraussichtlicher Kurzschlussstrom, welcher fließen kann, wenn Phase gegen Phase oder Neutralleiter kurzgeschlossen wird. 26 27 28 Test wird aktuell ausgeführt. Spannungswarnsymbol.
5.1.1 Symbole und Meldungen in der Spannungsfunktion Zeigt die richtigen Eingangsverbindungen an. Der Benutzer sollte die Messleitungen an die entsprechenden Klemmen anschließen. Zeigt an, daß keine Verbindung auf dem PEEingangsanschluss ist. Zeigt an, das die L-Verbindung auf dem NEingangsanschluss liegt und umgekehrt (Verpolung) Wenn die Verdrahtungsbedingungen anders als üblich sind (also L, N und PE ohne korrekte Verbindung), kann das Prüfgerät die vorgesehene Messfunktion nur eingeschränkt durchführen.
Fehlermeldungen: Mess... : Funktion in Betrieb – Messung wird durchgeführt RCD Trip: Während der Messung wurde der RCD (FI-Schutzschalter) ausgelöst, daher wurde kein Testergebnis erhalten Noise: Erscheint während der „No Trip“ Schleifenmessung und zeigt an, dass der angezeigte Wert wegen "Netzinterferenzen" nicht genau ermittelt werden konnte – Der Test muss wiederholt werden. 5.1.3 Symbole und Meldungen in der FI (RCD) Funktion Zeigt die richtigen Eingangsverbindungen an.
5.1.4 Symbole und Meldungen in der LOW OHM- oder Durchgangsfunktion Zeigt die korrekten Eingangsverbindungen an: Der Nutzer sollte die Prüfleitungen nach der Farbkodierung richtig anschließen. Batteriespannung ist ungenügend. Das Symbol blinkt und ein Warngeräusch ertönt. Der Eigenwiderstand der Prüfleitungen ist Bestandteil der Messung. Der Eigenwiderstand der Prüfleitungen ist nicht Bestandteil der Messung. 5.1.
5.2 Anwendung der LOOP / PFC-Funktion 1. Bevor Sie einen Schleifenimpedanz-Test machen, verwenden Sie die „Zero“ Funktion um die Messleitungen oder das Netzkabel zu „nullen“. Drücken und halten Sie F3-Taste für mehr als zwei Sekunden, bis die Meldung erscheint. Die Tester misst den Leitungswiderstand, speichert den Messwert im Speicher und subtrahiert diesen von den Messungen. Der Widerstandswert wird gespeichert, auch wenn die Stromversorgung ausgeschaltet.
Bei der Durchführung des Tests von einer 13A Steckdose werden die Klemmen automatisch von der oberen Stecker-Verbindung ausgewählt. 5.2.
F1 Taste F2 Taste F3 Taste F4 Taste ▲ Taste ▼ Taste Enter Taste Pop-Up Menü für Loop / PFC-Menü wird aktiviert. Pop-Up Menü für das Strommenü wird aktiviert. Keine Menüfunktion vorhanden Drücken Sie die Taste F4 für die Nullfunktion. Drücken um die aktuellen aktiven Optionen auszuwählen. Drücken um die aktuellen aktiven Optionen auszuwählen. Bestätigen Sie die Benutzerauswahl.
5.2.3 Hi Amp LOOP/PFC Messung Es sollte die Hi Amp LOOP Messung ausgewählt werden, wenn der Stromkreis nicht durch Einbeziehung eines FI (RCD) geschützt wird. 1. 2. 3. 4. Drehen Sie den Drehschalter in die LOOP / PFC Position. Drücken Sie F2-Taste, um von „No Trip“ to „Hi Amp“ umzuschalten. Schließen Sie die Messleitungen wie in der Abbildung gezeigt an. Sobald das Gerät ein Vorhandensein der Spannung an den Klemmen feststellt, wird die Messung automatisch durchgeführt: 5.
5.2.4. L-N Impedanz Messung 1. 2. 3. 4. Drehen Sie den Drehschalter in die LOOP/PSC - Position. Drücken Sie die F1-Taste, um von L-PE auf L-N umzuschalten. Schließen Sie die Messleitungen wie in der folgenden Abbildung dargestellt an. Sobald das Gerät eine Spannung an den Klemmen feststellt, wird die Messung automatisch durchgeführt: Wenn die Messung fertig gestellt wurde, erscheint der L-N und PSC Wert in der Anzeige: Drücken Sie die Test-Taste, wenn eine Wiederholung der Prüfung notwendig ist.
5.2.5 FI (RCD)-Test Funktion Sie können durch Drücken und Halten der F3-Taste (länger 2 Sekunden) die UL Spannung wählen (25 V oder 50 V). Der angezeigte Uf-Wert, ist die Berührungsspannung. Funktionstastenbeschreibung: Taste 1 2 3 4 5 6 F1 AUTO RCD t∆ RCD I∆N F2 30mA 100mA 300mA 500mA 650mA 1A F3 AC G AC S DC G DC S F4 0 180 G ……………………. Allgemein: FI-Schutzschalter ohne Verzögerung S …………………….
5.2.5.1 Anwendung der FI-Messfunktionen über die F1-Taste Anschluss bei der FI Messung 5.2.5.2 Anwendung des AUTO Modus Anzeige des AUTO Modus 1. 2. 3. 4. 5. Drehen Sie den Drehschalter in die Position RCD Der Einstiegsbildschirm ist das Setup des AUTO Modus Mit der F2-und F3-Taste, wählen Sie die Bewertung und den Typ des FIs aus Messleitungen anschließen, wie in der Abbildung gezeigt.
5.2.5.3 Anwendung des x½, x1, x2 und x5 Modus in manueller Auswahl 1. Drehen Sie den Drehschalter in die Position RCD 2. Drücken Sie F1-Taste um aus dem AUTO x½, x1, x2 und x5 Modus zu wählen 3. Mit der F2-und F3-Taste wählen Sie den Auslösestrom und die Art des FIs. (G=Allgemein / S=Selektiv) 4. Verbinden Sie die Messleitungen wie in der Abbildung gezeigt 5.
5.2.5.4 Anwenden der „Ramp“-Funktion Bei unbekannter Auslösegröße des Fehlerstroms kann die Ramp-Funktion genutzt werden um einen stetig steigenden Prüfstrom auszugeben. Wenn dieser den Auslösestrom des FI erreicht und damit ausgelöst hat, kann der Messwert als Bemessungsgrundlage für den FI verwendet werden. 1. 2. 3. 4. 5. 6. 7.
Menüanzeige F1 Taste F2 Taste F3 Taste F4 Taste ▲ Taste ▼ Taste Enter Taste Pop-Up Menü für Messart (Auto, Time, Ramp) wird geöffnet. Pop-Up Menü für Nenn-Auslösestrom (10mA bis 650mA) wird geöffnet. Pop-Up Menü für FI-Art und Form des Prüfstroms (Allgemein, Selektiv / Sinus, Halbwelle) wird geöffnet. Pop-Up Menü für die Prüfungspolarität (0° oder 180°) wird geöffnet. Drücken um die aktuellen aktiven Optionen auszuwählen. Drücken um die aktuellen aktiven Optionen auszuwählen.
5.2.8 Anwendung der Phasensequenzfunktion (Drehrichtungsanzeige) Startbild der Phasensequenzmessung 1. 2. 3. 4. Anschluss der Phasensequenzmessung Drehen Sie den Drehschalter in die Position VOLTAGE Drücken Sie F1 um auf Phasensequenz umzuschalten Schließen Sie die Messleitungen an L1, L2, L3 an, wie im Bild dargestellt Wenn das Gerät eingeschaltet ist, wird die Phasensequenz bei anliegenden Phasen (L1, L2, L3) automatisch angezeigt Richtige Phasensequenz L1, L2, L3 5.
5.2.9. Voltage/Phase Funktionsmenüs Hauptanzeige F1 Taste F2 Taste F3 Taste F4 Taste ▲ Taste ▼ Taste Enter Taste Menüanzeige Pop-up Menü für Spannungsmessung (L-PE, L-N, N-PE) oder Phasensequenz wird aktiviert Keine Keine Keine Drücken um die aktuellen aktiven Optionen auszuwählen. Drücken um die aktuellen aktiven Optionen auszuwählen. Bestätigen Sie die Benutzerauswahl.
5.3. Isolationswiderstandsmessung 5.3.1 Funktionsmenüs der Isoaltionsprüfung Hauptanzeige Menüanzeige F1 Taste F2 Taste F3 Taste F4 Taste ▲ Taste ▼ Taste Enter Taste Pop-Up Menü für die Prüfspannung wird aktiviert. Pop-Up Menü für den Warnsummer wird aktiviert. Pop-Up Menü für den Warnsummer wird aktiviert. Pop-Up Menü für den Referenzwert wird aktiviert. Drücken um die aktuellen aktiven Optionen auszuwählen. Drücken um die aktuellen aktiven Optionen auszuwählen. Bestätigen Sie die Benutzerauswahl.
5.3.2 Messung des Isolationswiderstands Isolationswiderstand / Schalter und Anschlusseinstellungen Messungen dürfen nur an spannungsfreien Stromkreisen durchgeführt werden. 1. Schalten Sie den Drehschalter in die „INSULATION“-Position. 2. Verwenden Sie die L und N (rot und schwarz) Klemmen für diesen Test. 3. Verwenden Sie die F1 Taste, um die Testspannung zu wählen. Die meisten Isolationsprüfungen werden bei 500 V durchgeführt, beachten Sie aber die vorgeschriebenen Testanforderungen. 4.
Die beste Genauigkeit wird erzielt, wenn der Abstand des mittleren Erdspießes ca. 62% der Strecke der Entfernung zum am weitesten entfernten Erdspieß erreicht, wie im folgenden Bild dargestellt: . Die Erdspieße sollten hierbei in einer geraden Linie aufgestellt und die Leitungen getrennt werden, um eine gegenseitige Kopplung zu vermeiden. Die getestete Erdungselektrode (z.B. Fundamenterder) sollte beim Test von der elektrischen Anlage getrennt werden.
5.4.1. Erdungswiderstand Funktionsmenü Hauptanzeige F1 Taste F2 Taste F3 Taste F4 Taste ▲ Taste ▼ Taste Enter Taste Keine Keine Keine Nullung der Prüfleitungen Drücken um die aktuellen aktiven Optionen auszuwählen. Drücken um die aktuellen aktiven Optionen auszuwählen. Bestätigen Sie die Benutzerauswahl. 5.5. Anwendung der Low-Ohm Messfunktion Eine Durchgangsprüfung wird verwendet um die Qualität der Verbindungen (Klemmen, Lötstellen etc.
Menüanzeige F1 Taste F2 Taste F3 Taste F4 Taste ▲ Taste ▼ Taste Enter Taste Pop-Up Menü zur Grenzwerteinstellung der Durchgangsprüfung Pop-Up zum Ein/Ausschalten des Summers Keine Nullung der Prüfleitungen Drücken um die aktuellen aktiven Optionen auszuwählen. Drücken um die aktuellen aktiven Optionen auszuwählen. Bestätigen Sie die Benutzerauswahl. 6. Optionen / Einstellungen Durch drücken der -Taste im Pfeiltastenfeld gelangt der Anwender aus jeder Messfunktion in das Optionsmenü.
6.1. Systemeinstellungen Symbol Menu Languages - Spracheinstellungen Date/Time - Datum Zeit TV – TV Ausgang Memory - Datenspeicheroptionen Auto screen-off – Automatische Bildschirmabschaltung Auto power-off – Automatische Geräteabschaltung System default settings – Werkseinstellungen System upgrade – Geräte Update Drücken Sie die ▲oder ▼ Tasten um durch das Systemmenü zu navigieren und bestätigen Sie die Auswahl mit der □ –Taste (Enter).
6.1.1. Sprachauswahl Drücken Sie die ▲oder ▼ Tasten um durch das Sprachmenü (Language) zu navigieren und bestätigen Sie die Auswahl mit der □ –Taste (Enter). Hinweis: Die zur Auswahl stehenden Sprachen können sich mit neueren Firmware-Versionen ändern. 6.1.2 Datum / Zeit Drücken Sie die ▲oder ▼ Tasten um die Einstellung des Datums (obere Zeile) oder der Uhrzeit (untere Zeile) auszuwählen und bestätigen Sie die Auswahl mit der □ –Taste (Enter).
6.1.3. TV-Ausgabe Das Gerät verfügt über die Möglichkeit das Anzeigebild als TV-Out Signal an einen Fernseher weiterzuleiten. Drücken Sie die ▲oder ▼ Tasten um durch das Menü zu navigieren und bestätigen Sie die Auswahl mit der □ –Taste (Enter). 6.1.4. Speichermenü (Memory) Drücken Sie die ▲oder ▼ um zwischen dem internen Speicher (Flash) oder einer Speicherkarte (SD-Card) umzuschalten. Bestätigen Sie die Auswahl mit der □ –Taste (Enter).
6.1.5. Automatische Bildschirmabschaltung Um die Einsatzdauer der geladenen Akkus zu verlängern, sollte sich der Bildschirm nach einigen Minuten automatisch deaktivieren (Auto Screen Off), da die Hintergrundbeleuchtung der größte Einzelverbraucher im Gerät ist. Drücken Sie die ▲oder ▼ um zwischen den verschiedenen Optionen umzuschalten, wobei 3 Minuten der Standard ist. Bestätigen Sie die Auswahl mit der □ –Taste (Enter). Die Option „Disable“ schaltet diese Funktion komplett ab. 6.1.
6.1.7. Werkseinstellungen Sollte das Gerät Probleme bei der Anwendung zeigen oder versehentlich Einstellungen verändert worden sein, kann eine Rücksetzung auf Werkseinstellungen (System Default) helfen. Drücken Sie die ▲oder ▼ Tasten um zwischen YES (JA) oder NO (NEIN) umzuschalten und bestätigen Sie die Auswahl mit der □ –Taste (Enter). 6.1.8.
7. Datenspeicher, Schnittstellen und Aufnahmefunktion 7.1 Aufnahmefunktion (Run Settings) Symbole Menü Bluetooth Ein/Aus Datenaufzeichnung (Einzelwert) Datenlogger (Messwertaufzeichnung) 7.2 Bluetooth Drücken Sie die ◄ oder ► Tasten um die Bluetooth Datenübertragung am Gerät ein- oder auszuschalten. Bestätigen Sie die Auswahl mit der ESC –Taste um in das vorausgehende Menü zurückzukehren. 7.3 Data Record Die Option Data Record zeichnet einen einzelnen Messwert als Textdatei auf.
7.4 Datalogger Die Option „Datalogger“ zeichnet nach Aktivierung die Messwerte des ausgewählten Bereiches in tabellarischer Form auf. Diese kann später auf den PC übertragen oder wieder als Bilddatei am Gerät dargestellt werden. Der Dateiname setzt sich automatisch aus dem Datum und der Uhrzeit der Aufnahme zusammen. Wird der Messbereich während der Messung verändert, stoppt die Aufnahme. Starten Sie ggf. in einem neuen Messbereich auch einen neuen Datenlogger.
7.5 Datenspeicher (Data Record) Im Menü Data Record sehen Sie eine Übersicht der zuvor abgespeicherten Messwerte als Textdatei für Einzelwerte oder Datalogger-Dateien. Drücken Sie die ▲oder ▼ Tasten um durch das Menü zu navigieren und bestätigen Sie die Auswahl mit der □ –Taste (Enter).
Wenn Sie eine aufgenommene Datei aus dem internen Speicher oder von der SD-Karte löschen wollen, wählen Sie die Datei mit den ▲oder ▼ Tasten aus und betätigen die HELP-Taste. Es erscheint das nachfolgende Pop-Up Fenster: Nutzen Sie die ▲oder ▼ Tasten zur Auswahl von YES (JA) oder NO (NEIN) und bestätigen Sie den Löschvorgang mit der □–Taste (Enter) 7.
7.7.
7.8 Kurvenfarbe (Drawing Color) Pop-Up Menü Taste ◄ ► ▲▼ ESC-Taste Funktion Umschalten zwischen D1 (Kurve 1) und D2 (Kurve 2) Farbauswahl für die angewählte Kurve umschalten. Einstellungen speichern und in das Menü zurückkehren.
8. Software 8.1 PC Software Öffnen Sie die “PeakTech Safety-Tester.exe” von der beiliegenden Software CD und installieren Sie das Programm auf Ihrem PC. Sie können die beiliegende Software nutzen um im Gerät abgespeicherte Messungen per USB auf Ihren PC zu übertragen oder die Daten in Echtzeit per Bluetooth Adapter in der Software aufzuzeichnen. Bei einer USB-Verbindung wird das Gerät als Wechselspeichermedium von Windows-Systemen erkannt, wodurch keine Treiberinstallation notwendig ist.
Nummer Funktion 1 Communicate 2 3 4 Language Help Meter Storage 5 6 15 Protokolldaten Start-Time / Samples Connected COM Disconnect Messwertanzeige Funktion Tap to Record Stop Measure Panel/ History Record Messwerttabelle 16 Export Excel 17 Print 7 8 9 10 11 12 13 14 Bedeutung Auswahl der Kommunikationsbedingungen COM-Port: Bluetooth Verbindung über einen virtuellen COM-Port Meter Storage: Auslesen des internen Speichers über USB Auswahl der Sprache Öffnet die Hilfe-Funktion Zeigt bei angeschloss
8.2. App für Smartphones Laden Sie die App „PeakTech Safety Tester“ kostenfrei aus dem App-Store oder installieren Sie die apk-Datei von der CD manuell (nur Android). Öffnen Sie die Applikation und stellen Sie eine Bluetooth-Datenverbindung her. Beachten Sie dabei, daß sowohl am Installationstester, als auch an Ihrem Smartphone die Bluetooth Schnittstelle aktiviert ist. Die Applikation für Smartphones kann Daten aus dem Messgerät auf Tastendruck in die Messwerttabelle übertragen bzw.
1. Introduction This product complies with the requirements of the following European Community Directives: 2004/108/EC (Electromagnetic Compatibility) and 2006/95/EC (Low Voltage) as amended by 2004/22/EC (CE-Marking). Overvoltage category CAT III 600V ; pollution degree 2. 2. Safety Precautions To ensure safe operation of the equipment and eliminate the danger of serious injury due to short-circuits (arcing), the following safety precautions must be observed.
2.1. Safety Symbols Attention! Risk of electric shock! Do not open the case during a measuring process! Attention! Do not apply over-voltage to the input jacks! Remove the test set cords before opening the battery compartment! Cleaning - Use a dry cloth to clean the housing! Observe all safety notes in the operating instructions! Earthing Double isolation Fuse Don’t use in live systems which exceed 550V TÜV/GS-approved, TÜV Rheinland 2.2.
3. Specifications LOOP Resistance L- PE (Hi-Amp) Range (Ω) Resolution(Ω) Accuracy 0.23 – 9.99 0.01 10.0 – 99.9 0.1 ±(4% of reading+ 6digits) 100 – 999 1 Measuring Current …………….………………………………………..………… 4.0 A Range of the Voltage Used …………………………195V AC – 260V AC (50,60Hz) L- PE (No Trip) Range (Ω) Resolution(Ω) Accuracy 0.23 – 9.99 0.01 10.0 – 99.9 0.1 ±(5% of reading+ 6 digits) 100 – 999 1 Measuring Current ……………..
Voltage and Frequency Measurement Range 80 – 500 V AC/DC 45 – 65 Hz Earth resistance Range 0.000~9.999Ω 10.00~99.99Ω 100.0~999.9Ω 1000 ~2000Ω Resolution 1V 1 Hz Resolution Accuracy 0.001Ω 0.01Ω 0.1Ω 1Ω +(1.5%+30dgt) Accuracy ±(2% of reading + 2digits) ±2Hz Max. open Circuit Voltage Overload Protection 5.8V 250Vrms +(2%+6dgt) Low Ohm Range 0.00~99.99Ω 100.0~999.9Ω 1000~2000Ω Insulation Terminal Voltage 125V (0%~+10%) 250V (0%~+10%) 500V (0%~+10%) 1000V (0%~+10%) Resolution 0.01Ω 0.
3.1 General Specifications Power Source ………………………………….. 12V DC (8 x 1.5V AA Size Alkaline batteries) Battery Life…………………………………………………………..……….. Average of 15hours CAT Rating…. ……………………………………………………….…………….….CAT III 600V Protection Classification ……………………………………………………..…Double Insulation Protection Rating ……………………………………………………………..…………………IP65 LCD Display ………………………………………….……………...............320x240 dots matrix Operating Temp…………………………………………………………………………..0℃~ 45℃ Relative Humidity …………….…………..
LOOP PFC LOOP/PFC PSC Current No Trip Current Hi Amp Zero V V/Phase The loop impedance is the sum of all the resistance components of a current loop, which is traversed in an error from the error stream. The resistance should be as low as possible, so that at high fault currents no heat is generated in the lines and thereby electrical fire, until the protective measures triggers and interrupts the faulty circuit.
Continuity Low Ohm mA Beeper Zero (RE) RE Zero Isolation resistance Terminal Voltage Insulation Beeper Lock Reference A continuity test is used for checking of intact compounds in a nonactive circuit. If all modules are connected correctly, the resistance should be as low as possible. When corroded, charred or badly screwed connections, the resistance is higher (contact resistance), which can ultimately lead to fire. Various limits (0.5, 1, 2.5 and 10 ) can be set.
4. Control 4.1. Function keys 6 No. 1 2 3 4 5 6 7 8 3 2 1 4 5 8 7 Description Starts the selected test. The T key is surrounded by a “touch pad”. The touch pad measures the potential between the operator and the tester’s PE terminal. If you exceed a 100 V threshold, the D symbol above the touch pad is illuminated. Warning lamp 320X(RGB)X240 color active matrix Press and hold Turns the tester on and off.
4.2. Connections No.
4.3. Batteries and Fuses No.
4.4. Display / Symbols Number Function Value/Meaning AUTO x½ x1 x2 x5 RCD RAMP Loop/PFC 1 V/Phase Continuity Terminal Voltage L-PE L-L L-N L-PE 0.5Ω 1.0Ω 2.0Ω 5.0Ω 10.0Ω 20.0Ω 50.
Number Function Trip Current 2 Current Beeper Value/Meaning 30mA 100mA 300mA 500mA 650mA 1000mA 10mA No Trip Hi Amp OFF ON Type of RCD 3 Lock 0°/180° OFF ON 0° 180° ZERO 4 Reference 5 Date / Time 0.125MΩ 0.25MΩ 0.
Number 11 Symbol Value/Meaning Bluetooth connection activated 12 Overheat warning Display 30 seconds (time-delayed) RCDs 13 Measurement function under test 14 Primary display and measurement units. 15 16 Primary display and measurement units. 17 18 Fault voltage. Measures neutral to earth. 19 Indicates the preset fault voltage limit. 20 Arrows above or below the terminal indicator symbol indicate reversed polarity. Check the connection or check the wiring to correct it.
5. How to use the Tester 5.1. Important symbols and messages during the measurement Description: 1. Battery status 2. Displayed measured value 3. The measurement unit of the measured value 4. The indication of the correct input terminal connection 5.
5.1.1 Displayed icons (symbols) and messages in VOLTAGE function Indicates the correct input terminal connectivity. The user should connect the test leads to the appropriate terminals. Indicates L connection is connected on the N input terminal and vice-versa Indicates no connection on the PE input terminal If the wiring condition is other than normal, the Tester is limited on its measurements that can be performed. Notes: 1) Will not detect two hot wires in a circuit.
5.1.2. Displayed icons (symbols) and messages in LOOP/PFC function Indicates the correct input terminal connectivity. The user should connect the test leads to the appropriate terminals. Indicates L connection is connected on the N input terminal and vice-versa Indicates no connection on the PE input terminal If the wiring condition is other than normal, the Tester is limited on its measurements that can be performed. Notes: 1) Will not detect two hot wires in a circuit.
5.1.3. Displayed icons (symbols) and messages in RCD function Indicates the correct input terminal connectivity . The user should connect the test leads to the appropriate terminals. Indicates L connection is connected on the N input terminal and vice-versa Indicates no connection on the PE input terminal If the wiring condition is other than normal, the Tester is limited on its measurements that can be performed. Notes: 1) Will not detect two hot wires in a circuit.
5.1.4. Displayed icons (symbols) and messages when using the LOW OHM and CONTINUITY functions Symbol Indicates correct input terminal connectivity. The user should connect the test leads to the appropriate terminals indicated by color coding. Low Battery (The icon will be flashing along with the beep sound) The resistance of the test leads are included in the test measurement The resistance of the test leads are not included in the test measurement 5.1.5.
5.2 USING THE LOOP / PFC FUNCTION 1. Before you do a loop impedance test, use the zero adapter to zero the test leads or the mains cord. Press and hold F3 button for more than two seconds until the annunciator appears. The tester measures the lead resistance, stores the reading in memory, and subtracts it from readings. The resistance value is saved even when the power is turned off so it is unnecessary to repeat the operation each time you use the tester with the same test leads or mains cord.
No Trip Loop No Trip LOOP – Test lead connection When carrying out the test from a 13A socket the points of contact are automatically selected by the plug top connection -69-
5.2.2 LOOP / PFC Function Menu Operation Main Display Menu Display F1 Button F2 Button F3 Button F4 Button Up Button Down Button Enter Button Pop-up and shutdown Loop/PFC menu, Shutdown mode is activated when the user selects. Pop-up and shutdown Current menu, Shutdown mode is activated when the user selects. None Press the F3 button, triggering zero function. Up menu to select the current active sub-options. Down menu to select the current active sub-options. Confirm the user select mode.
5. When measuring is completed, impedance of L- PE and PFC (lf) value appears on the screen No Trip – Measurement completed 6. Press TEST button if re-test is necessary. When symbol from , , the voltage exceeds 260V, the measurement will not take place appears lower left corner, and if 5.2.3 Using the Hi Amp LOOP Measurement The Hi Amp LOOP Measurement to be selected where the circuit is NOT protected by the inclusion of an RCD. Hi Amp Loop – Standby screen 1. 2. 3. 4.
Hi Amp LOOP – To be used where NO RCD is present Hi Amp LOOP – Test lead connection 5. When the measuring is complete the impedance of L-PE and PFC (lf) value appears on the screen Hi Amp LOOP – Measurement finished 6.
5.2.4 Using the L- N Line Impedance Measurement L-N Line – Standby screen 1. 2. 3. 4. Turn the rotary switch to the LOOP / PSC position Press F1 button to change from L - PE to L - N Connect the test leads as shown in Figure 5.2.3.3 As soon as the instrument senses the presence of voltage and if properly connected, the measurement will be taken automatically L-N Line Impedance – When measuring L-N Line Impedance – Test leads connection 5.
6. Press TEST button if re-test is necessary When symbol from , , appears lower left corner, and if the voltage exceeds 260V, the measurement will not take place 5.2.5 Using the RCD Function You can select UL Voltage by Pressing and hold F3 button for more than two seconds (25V or 50V). Uf value appears is the contact voltage on the screen. RCD – Standby screen Function Button Description BUTTON 1 2 3 4 5 F1 AUTO RCD t∆ RCD I∆N F2 30mA 100mA 300mA 500mA 650mA F3 AC G AC S DC G DC S F4 0 180 G …………………….
Maximum measurement Trip Time of the RCD (Complying to BS 61008 and 61009) 1/2 x I∆N I∆N 2 x I∆N 5 x I∆N General (nont∆= t∆= t∆= t∆= Max.40mS delayed) RCD Max.1999mS Max.500mS Max.150mS Selective t∆= t∆= t∆= t∆= Max.40mS (time-delayed) Max.1999mS Max.500mS Max.150mS RCDs I∆N………………………... Trip-Out Current t∆…………………………. Trip-Out Time : Indicates that the thermal protection device has operated and therefore cannot make any measurements. Instrument must be allowed to cool for a period before tests can continue.
5.2.5.2 Using the AUTO Mode RCD Auto Function Screen 1. 2. 3. 4. 5. Turn the rotary switch to the RCD position Initial screen is setup to the AUTO Using the F2 and F3 button, select the rating and the type of the RCD Connect test leads as shown in the Figure 5.2.4.1 If --- from the lower right corner disappears and voltage of the L- PE on the lower left appears, the unit is ready to TEST (If N and PE test leads are reversed, the instrument will still carry out the test) 6.
5.2.4.3 Using the x1/2, x1, x2 and x5 manual selection x1 Mode – Measuring screen 1. Turn the rotary switch to the RCD position 2. Press F1 and aspect button from the AUTO to select x1/2, x1,x2, and x5 3. Using the F2 and F3 button, select the RCD’s trip current and type of the RCD. (General/Selective) 4. Connect the test leads as shown in Figure above 5.
5.2.4.4 Using the RAMP function RCD Ramp – Measuring screen 1. 2. 3. 4. 5. 6.
5.2.6 RCD Function Menu Operation Main Display RCD AUTO Other Menu Display F1 Button F2 Button F3 Button F4 Button Up Button Down Button Enter Button Pop-up and shutdown RCD menu , Shutdown mode is activated when the user selects.
5.2.7 Using the VOLTAGE Function WARNING! Do not use on a circuit whose voltage either L-L or L-N exceeds 550V Measuring the Voltage and Frequency Standby screen for the Voltage and Frequency 1. Connect the test lead input terminal 2. Turn the rotary switch to the VOLTAGE position Screen while measuring Voltage and Frequency Do not attempt to measure when the input voltage is above 500V AC.
5.2.8 Using the Phase Sequence Function Determining the Phase Sequence Phase Sequence – Test lead connection Initial screen of the Phase Sequence Measurement 1. 2. 3. 4. Turn the rotary switch to the VOLTAGE position Press F1 to make symbol is displayed Connect the test leads L1, L2, L3 as shown on theFigure 5.2.6.2 When the instrument is energized the sequence will be displayed automatically Phase Sequence screen -when connected in clockwise direction.
When the line conductors are connected in the correct sequence 1.2.3 and the symbol will appear as the Figure above. However, connected in the wrong sequence, 2.1.3 and the circle symbol will change to the symbol displayed below: Phase Sequence – When connected in counter-clockwise manner 5.2.9.
5.3. Isolation Measurement 5.3.1. Function menus of the isolation measurement Main Display Menu Display F1 Button F2 Button F3 Button F4 Button Up Button Down Button Enter Button Pop-up and shutdown RCD menu, Shutdown mode is activated. Pop-up and shutdown RCD menu, Shutdown mode is activated. Pop-up and shutdown RCD menu, Shutdown mode is activated. None Up menu to select the current active sub-options. Down menu to select the current active sub-options. Confirm the user select mode.
5.3.2. To measure insulation resistance 1. Turn the rotary switch to the INSULATION position. 2. Use the L and N (red and black) terminals for this test. 3. Use the F1 to select the test voltage. Most insulation testing is performed at 500 V, but observe local test requirements. 4. Press and hold TEST button until the reading settles and the tester beeps. Note Testing is inhibited if voltage is detected in the line. The primary (upper) display shows the insulation resistance.
Best accuracy is achieved with the middle stake at 62 % of the distance to the far stake. The stakes should be in a straight line and wires separated to avoid mutual coupling. The earth electrode under test should be disconnected from the electrical system when conducting the test. Earth resistance testing should not be performed on a live system. To measure earth resistance 1. Turn the rotary switch to the RE position. 2. Press and release TEST button. Wait for the test to complete.
5.5. Using the LOW-Ohm function A continuity test is used to verify the integrity of connections by making a high resolution resistance measurement. This is especially important for checking Protective Earth connections. 5.5.1. LOW OHM Function Menu Operation Main Display Menu Display F1 Button F2 Button F3 Button F4 Button Up Button Down Button Enter Button Pop-up and shutdown RCD menu , Shutdown mode is activated when the user selects.
6. Options and settings Items Menu System Settings Data Record Run Settings Press the ◄ and ► button to select the System Settings, Data Record or Run Settings. Then press the □ button to enter. 6.1.
6.1.1. Language Selection Press the ▲ and ▼ button to select the language, press ESC button to esc and save the select the language. Note: The available languages may change in newer firmware versions. 6.1.2. Date and Time Press the ▲ and ▼ button to select the date or time, then press the □ button to enter, Press the ▲ and ▼ button to adjust the value. Press the ◄and ►button to select the Items, press the ESC button to esc and save.
6.1.3. TV Output Press the ▲ and ▼ button to select the output format. Then press the □ button to enter. 6.1.4. Memory Menu Press the ◄and ►button to select the Working Space or Format. Then press the □ button to enter, press the ESC button to esc and save. Note: With the "Format" option to format the internal memory or the SD card. All stored in memory are deleted and cannot be restored! 6.1.5.
6.1.6. Auto Power Off Default 10 Minutes, Press the ▲ and ▼ button to select the Auto power-off time, press ESC button to esc and save the select the time. To prolong the operating time of the charged batteries, the device should automatically turn off after a few minutes (Auto Power Off). This provides a complete discharge of the battery is prevented; the device should not have been accidentally switched off manually. 6.1.7. Factory Reset Press the □ button to enter.
7. Data storage, interfaces and recording function 7.1. Run Settings Items Menu On or off the Bluetooth Data Record Datalog Press the ▲ and ▼ button to select the Items. Then press the □ button to enter 7.2. Bluetooth Press the ◄and ►button to select the on or off Bluetooth, press the ESC button to esc and save.
7.3. Data Record The Data Record option records a single reading on a text file. These can then transfer to a PC or are again displayed as image file on the device. You can select the file name free by navigating with the arrow keys on the virtual keyboard: Items Menu F1 button Backspace F2 button Enter Data Record □ Enter characters Press the ◄ ► ▲ ▼ button to select the characters , press the □ button to Enter characters. 7.4.
Example of a logged text-file: 7.5. Data record In the Data Record menu, you see a list of previously stored measurement values to a text file for single values or data logger files. Press the ▲ or ▼ keys to scroll through the menu and confirm your selection by pressing the □ button (Enter).
Press the ESC key to return to the selection of the stored text files. If you want to delete a recorded file from the internal memory or the SD card, select the file with the ▲ or ▼ buttons and press the HELP key. It appears the following pop-up window: Use the ▲ or ▼ buttons to select YES (YES) or NO (NO) and confirm the deletion by pressing the □ button (Enter) 7.6.
7.7. Drawing Number 1 Display File Name 2 Primary display and measurement units. Primary display and measurement units.
7.8. Drawing Color Pop-Up Menu Key Function ◄ ► ▲▼ ESC-Key Switch between D1 (curve 1) and D 2 (curve 2) Color selection for the selected curve switch. Save settings and return to the menu. 8. Software 8.1 PC software Open the "PeakTech Safety Tester.exe" from the included software CD and install the program on your PC. You can use the included software to transfer stored measurement data via USB to your PC or record the data in real time via Bluetooth adapter in the software.
Number 1 Function Communicate 2 3 4 Language Help Meter Storage 5 6 15 Protokolldaten Start-Time / Samples Connected COM Disconnect Messwertanzeige Funktion Tap to Record Stop Measure Panel/ History Record Messwerttabelle 16 17 Export Excel Print 7 8 9 10 11 12 13 14 Meaning Selecting the communication conditions COM port: Bluetooth connection via a virtual COM port, Meters Storage: reading the internal memory via USB Selecting the language Opens the Help function Displays when connected to USB co
8.2. App for mobile phones Download the app "PeakTech Safety Tester" for free from the App Store or install the apk-file from the CD manually (Android only). Open the application and start a Bluetooth data connection. Please ensure that on both devices, the installation safety tester and your mobile phone, the Bluetooth interface is enabled and active.