PeakTech® 6120 Bedienungsanleitung / Operation Manual AC/DC-Labornetzgerät / Power Supply
1. Sicherheitshinweise Dieses Gerät erfüllt die EU-Bestimmungen 2004/108/EG (elektromagnetische Kompatibilität) und 2006/95/EG (Niederspannung) entsprechend der Festlegung im Nachtrag 2004/22/EG (CEZeichen). Zur Betriebssicherheit des Gerätes und zur Vermeidung von schweren Verletzungen durch Stromoder Spannungsüberschläge bzw. Kurzschlüsse sind nachfolgend aufgeführte Sicherheitshinweise zum Betrieb des Gerätes unbedingt zu beachten.
* Keine technischen Veränderungen am Gerät vornehmen. * -Messgeräte gehören nicht in Kinderhände1.1. Reinigung des Gerätes: Vor dem Reinigen des Gerätes, Netzstecker aus der Steckdose ziehen. Gerät nur mit einem feuchten, fusselfreien Tuch reinigen. Nur handelsübliche Spülmittel verwenden. Beim Reinigen unbedingt darauf achten, dass keine Flüssigkeit in das Innere des Gerätes gelangt. Dies könnte zu einem Kurzschluss und zur Zerstörung des Gerätes führen. 2.
3.1. Anzeigen und Bedienelemente 9. 10. 11. 12. 8. 7. 1.) 2.) 3.) 4.) 5.) 6.) 7.) 8.) 9.) 10.) 11.) 12.) 6. 5. 4. 3. 2. 1.
3.2. Betrieb 1.) 2.) 3.) 4.) Verbinden Sie den Verbraucher / Last mit dem Netzgerät. Nach Einschalten des Netzgerätes wird die Ausgangsspannung und der Ausgangsstrom im LED-Display angezeigt. Drehen Sie am Einstellknopf zur Einstellung der Ausgangsspannung (11), um die gewünschte Spannung einzustellen Betätigen Sie den AC/DC-Umschalter (8), um die gewünschte Spannungsart auszuwählen. Drücken Sie die Smoothing-Taste (2), um eine geglättete DC-Spannung am Ausgang zu erhalten.
1. Safety precautions This product complies with the requirements of the following European Community Directives: 2004/108/EG (Electromagnetic Compatibility) and 2006/95/EG (Low Voltage) as amended by 2004/22/EG (CE-Marking). To ensure safe operation of the equipment and eliminate the danger of serious injury due to shortcircuits (arcing), the following safety precautions must be observed. Damages resulting from failure to observe these safety precautions are exempt from any legal claims whatever.
2. General The PeakTech® 6120 connects easy handling, a sturdy case, novel appearance and a good performance with an excellent cost effectiveness. It is the ideal power supply unit for science investigation, college, factory, electronic appliance maintenance and etc. * The model PeakTech® 6120 is AC and DC power supply, with its adjustable voltage output (Both AC and DC). * The DC is only rectified. Output voltage is continuously adjustable.
3.1. Controls and description 9. 10. 11. 12. 8. 7. 1.) 2.) 3.) 4.) 5.) 6.) 7.) 8.) 9.) 10.) 11.) 12.) 6. 5. 4. 3. 2.
3.2. Operating method 1.) 2.) 3.) 4.) First connecting the load to the power supply. After the unit is switched on, output voltage and current will be indicated by LED Turning the output voltage adjustment to adjust the voltage Using the AC or DC switch to choose the AC or DC Pressing on the smoothing switch to get the smoothed DC. NOTE: When DC is smoothed, the voltage will be higher than the voltmeter’s value.