PeakTech 6140 / 6150 Bedienungsanleitung / Operation manual Stabilisierte Labornetzgeräte / Regulated Laboratory Power Supplies
Sicherheitshinweise zum Betrieb der Geräte Dieses Gerät erfüllt die EU-Bestimmungen 2004/108/EG (elektromagnetische Kompatibilität) und 2006/95/EG (Niederspannung) entsprechend der Festlegung im Nachtrag 2004/22/EG (CEZeichen). Zur Betriebssicherheit der Geräte und zur Vermeidung von schweren Verletzungen durch Stromoder Spannungsüberschläge bzw. Kurzschlüssen sind nachfolgend aufgeführte Sicherheitshinweise zum Betrieb der Geräte unbedingt zu beachten.
Einführung Die Labornetzgeräte sind gegen Überlast und Kurzschluss abgesichert. Die jeweils eingestellte Ausgangsspannung bzw. der eingestellte Ausgangsstrom wird über eine 3-stellige LCD-Anzeige. Durch die außergewöhnlichen Leistungsmerkmale sind diese Netzgeräte hervorragend geeignet für den Einsatz im Forschungs- und Entwicklungsbereich, in Technischen Hochschulen, der Elektroindustrie und für den mobilen Wartungs- und Reparaturdienst.
1.
2. Betrieb der Geräte 2.1. Anzeigen und Bedienelemente des P 6140 1. 9. 10. 2. 3. 2a. 8. 4. 7. 01. 02. 2a. 03. 04. 05. 06. 07. 08. 09. 10. 6. 5.
2.3. Anzeigen und Bedienelemente des P 6150 2. 1. 3. 9. 11. 10. 8. 12. 4. 7. 01. 02. 03. 04. 05. 06. 07. 08. 09. 10. 11. 12. 6. 5.
2.6. Betrieb 1. Einstellen der gewünschten Ausgangsspannung. Ampere-Regler (3.) auf Rechtsanschlag drehen und Gerät mit der Ein-/Aus-Taste (4.) einschalten. Gewünschte Ausgangsspannung am Ausgang mit den Spannungsreglern (2.) einstellen. Die Konstantstrom-Anzeige (9.) erlischt und die Konstantspannungsanzeige (10.) leuchtet auf. 2. Zur Einstellung des gewünschten Ausgangsstromes. Gerät mit der Ein-/Aus-Taste (4.) einschalten und Spannungsregler (2.) auf Rechtsanschlag und Ampere-Regler (3.
Safety Precautions This product complies with the requirements of the following European Community directives: 2004/108/EC (Electromagnetic Compatibility) and 2006/95/EC (Low Voltage) as amended by 2004/22/EC (CE-Marking). To ensure safe operation of the equipment and eliminate the danger of serious injury due to short circuits (arcing), the following safety precautions must be observed. Damages resulting from failure to observe these safety precautions are exempt from any legal claims whatever.
Introduction The regulated laboratory power supplies with fine adjustable (not for P 6035 D/P 6040 A) output voltage are provided with overload and short circuit protection. There are 3 digit LDC displays for Volt and Ampere (P 6005 D/P 6035 D) or analogue Volt and Ampere (P 6000 A/P 6015 A/ P 6040 A) for indicating the output with high accuracy.
1.
2. Operation 2.1. Controls and description P 6140 1. 9. 10. 2. 3. 2a. 8. 4. 7. 01. 02. 2a. 03. 04. 05. 06. 07. 08. 09. 10. 6. 5.
2.3. Controls and description P 6015 A 2. 1. 3. 9. 11. 10. 8. 12. 4. 7. 01. 02. 03. 04. 05. 06. 07. 08. 09. 10. 11. 12. 6. 5.
2.6. Operating method 1. When the adjustable output is used as CV output, first should rotate clockwise the CC adjustment (3.) to maximum, then turn on power switch (4.), adjust CV adjustment (2.) till output voltage reach required voltage value, at this time, the CC state indicator (9.) go out the CV state indicator (10.) light on. 2. Used as CC output, after turning on power switch (4.), first rotate clockwise the CV adjustment (2.) to maximum, while rotate counterclockwise the CC adjustment (3.
All rights, also for translation, reprinting and copy of this manual or parts are reserved. Reproductions of all kinds (photocopy, microfilm or other) only by written permission of the publisher. This manual is according the latest technical knowing. Technical changings which are in the interest of progress, reserved. We herewith confirm that the units are calibrated by the factory according to the specifications as per the technical specifications. We recommend to calibrate the unit again, after 1 year.