6155/6160 Bedienungsanleitung / Operation manual Labor-DC-Schaltnetzteil / Laboratory Switching Mode Power Supply
1. Sicherheitshinweise zum Betrieb des Gerätes Dieses Gerät erfüllt die EU-Bestimmungen 2004/108/EG (elektromagnetische Kompatibilität) und 2006/95/EG (Niederspannung) entsprechend der Festlegung im Nachtrag 2004/22/EG (CEZeichen). Zur Betriebssicherheit des Gerätes und zur Vermeidung von schweren Verletzungen durch Stromoder Spannungsüberschläge bzw. Kurzschlüsse sind nachfolgend aufgeführte Sicherheitshinweise zum Betrieb des Gerätes unbedingt zu beachten.
. Technische Daten Spannungsversorgung: 230 V AC; 50 Hz Ausgangsspannung: Ausgangsstrom: 1 - 30 V DC P 6155 = 0 ~ 20 A P 6160 = 0 ~ 30 A Restwelligkeit: (0-100% Last) 100 mVpp Überlastschutz: Strombegrenzerschaltung und kurzschlussfest Genauigkeit Spannungsanzeige: ± 1 % + 3 Stellen Stromanzeige: ± 1 % + 3 Stellen Abmessungen : (BxHxT) 336 x 87 x 214 mm Gewicht : 3 kg Zubehör: Netzkabel und Bedienungsanleitung -2-
. Betrieb 3.1. Anzeigen und Bedienelemente an der Vorderseite des Gerätes PeakTech 6155 (1) Netzschalter: "ON" / "OFF" (2) + Ausgang (positiv) (3) – Ausgang (negativ) (4) Spannungsregler (5) Stromregler (6) Spannungsanzeige (7) Stromanzeige (8) Konstantspannungsanzeige (C.V.) leuchtet im Konstantspannungs-Modus (9) Kontantstromanzeige (C.C.
PeakTech 6160 (1) Netzschalter: "ON" / "OFF" (2) + Ausgang (positiv) (3) – Ausgang (negativ) (4) Spannungsregler (5) Stromregler (6) Spannungsanzeige (7) Stromanzeige (8) Konstantspannungsanzeige (C.V.) leuchtet im Konstantspannungs-Modus (9) Kontantstromanzeige (C.C.
(Rückansicht) (10) Ausgangsbuchsen: max. 20A (P 6155) / 30A (P 6160); rot=positiv; blau=negativ (11) Lüfter (12) Sicherung (13) Erdungsklemme 5. Betrieb des Gerätes 1. 2. 3. Zur Einstellung der konstanten Ausgangsspannung drehen Sie den Stromregler (5) im Uhrzeigersinn bis zum Anschlag. Schalten Sie das Gerät mit dem Netzschalter (1) ein und stellen Sie mit dem Spannungsregler (4) die gewünschte Ausgangsspannung ein. Dann verbinden Sie die Last mit den Ausgangsbuchsen (10).
6. Achtung ! Im Falle eines Kurzschlusses am Ausgang wird der Strom begrenzt durch die Stromkontrollen, allerdings sollte das Gerät ausgeschaltet werden und der Kurzschluss beseitigt werden vor der weiteren Nutzung. Der Hauptstrom muss vor der Wartung ausgeschaltet werden und die Wartung sollte nur von qualifiziertem Personal durchgeführt werden.
1. Safety Precautions This product complies with the requirements of the following European Community Directives: 2004/108/EC (Electromagnetic Compatibility) and 2006/95/EC (Low Voltage) as amended by 2004/22/EC (CE-Marking). To ensure safe operation of the equipment and eliminate the danger of serious injury due to shortcircuits (arcing), the following safety precautions must be observed. Damages resulting from failure to observe these safety precautions are exempt from any legal claims whatever.
Cleaning the cabinet Prior to cleaning the cabinet, withdraw the mains plug from the power outlet. Clean only with a damp, soft cloth and a commercially available mild household cleanser. Ensure that no water gets inside the equipment to prevent possible shorts and damage to the equipment. 2. Introduction These both power supplies in modern design constructed especially for the service centers and education fields.
4. Operation 3.1.
PeakTech 6160 (1) Power Switch: "ON" / "OFF" (2) Positive output (3) Negative output (4) Voltage Adjustment Knob (5) Current Adjustment Knob (6) Regulated Voltage Indication (7) Regulated Current Indication (8) Constant Voltage mode indication (9) Constant Current mode indication - 10 -
(Back view) (10) Output terminal: max. 20A (P 6150) / 30A (P 6160); red=positive; blue=negative (11) Cooling fan (12) Fuse (13) Grounding terminal 5. Operating Method 1. For constant voltage mode adjust controls (5) clockwise to the maximum position. Switch on the power ON/OFF switch (1) and adjust controls (4) to set the desired output voltage. Connect the load to the output terminal (10). 2. For constant current mode adjust controls (4) clockwise to the maximum position.
6. Caution In the event of a short circuit at the output the current will limit at the value set by the current controls, however the unit should be turned off and the short circuit removed before continuing use. The mains power must be switched off before servicing and servicing should be referred to a qualified person. The unit should be stored in a dry and well ventilated place and the power cord removed if storing for long periods. Laboratory Power Supplies are not designed for charging batteries.