PeakTech® 8010 Bedienungsanleitung / Operation manual Schallpegelkalibrator / Sound Level Calibrator
1. Sicherheitshinweise zum Betrieb des Gerätes Dieses Gerät erfüllt die EU-Bestimmungen 2004/108/EG (elektromagnetische Kompatibilität) entsprechend der Festlegung im Nachtrag 2004/22/EG (CE-Zeichen). Verschmutzungsgrad 2. Zur Betriebssicherheit des Gerätes sind nachfolgend aufgeführte Sicherheitshinweise zum Betrieb des Gerätes zu beachten. Schäden, die durch Nichtbeachtung dieser Hinweise entstehen, sind von Ansprüchen jeglicher Art ausgeschlossen.
Reinigung des Gerätes Gerät nur mit einem feuchten, fusselfreien Tuch reinigen. Nur handelsübliche Spülmittel verwenden. Beim Reinigen unbedingt darauf achten, das keine Flüssigkeit in das Innere des Gerätes gelangt. Dies könnten zu einem Kurschluss und zur Zerstörung des Gerätes führen. 2. Allgemeines Der Schallpegelkalibrator PeakTech® 8010 erfüllt die Anforderungen nach EN 60942:2003 Klasse2 und dient zur Überprüfung der Genauigkeit von Schallpegelmessgeräten.
3. Anschlüsse und Bedienelemente am Gerät 1 2 3 1. 2. 3.
4. Messbetrieb 1. Führen Sie das Mikrofon Ihres Schallpegelmessgerätes in die Kalibrieröffnung des PeakTech 8010. Achten Sie darauf, dass das Mikrofon vollständig in die Kalibrieröffnung eingesteckt ist. 2. Wählen Sie mit Hilfe des Wahlschalters (2) den benötigten Schallpegel aus; 94 oder 114 dB. 3. Lesen Sie nun den Messwert in der Anzeige Ihres Schallpgelmessgerätes ab. 4. Sollte der Messwert nicht mit dem voreingestellten Kalibriersignal übereinstimmen, können Sie das Schallpegelmessgerät neu abgleichen.
. Auswechseln der Batterie Wird kein Schalldruckpegel ausgegeben, dann muss die Batterie ausgewechselt werden Dazu wie beschrieben vorgehen: 1. Schraube der Batteriefachabdeckung auf der Rückseite lösen und Abdeckung vom Batteriefach entfernen, 2. verbrauchte Batterie aus dem Batteriefach entfernen und vom Batteriekabel abziehen, 3. neue 9 V Batterie an das Batteriekabel anschließen und Batterie in das Batteriefach einsetzen 4.
Gesetzlich vorgeschriebene Hinweise zur Batterieverordnung Im Lieferumfang vieler Geräte befinden sich Batterien, die z. B. zum Betrieb von Fernbedienungen dienen. Auch in den Geräten selbst können Batterien oder Akkus fest eingebaut sein.
Alle Rechte, auch die der Übersetzung, des Nachdruckes und der Vervielfältigung oder Teilen daraus, vorbehalten. Reproduktion jeder Art (Fotokopien, Mikrofilm oder ein anderes Verfahren) nur mit schriftlicher Genehmigung des Herausgebers gestattet. Letzter Stand bei Drucklegung. Technische Änderungen des Gerätes, welche dem Fortschritt dienen, vorbehalten. Hiermit bestätigen wir, dass alle Geräte die in unseren Unterlagen genannten Spezifikationen erfüllen und werkseitig kalibriert geliefert werden.
1. Safety Precautions This product complies with the requirements of the following European Community Directives: 2004/108/EC (Electromagnetic Compatibility) as amended by 2004/22/EC (CE-Marking). Pollution degree 2. To ensure safe operation of the equipment the following safety precautions must be observed. Damages resulting from failure to observe these safety precautions are exempt from any legal claims whatever.
Cleaning the cabinet Clean only with a damp, soft cloth and a commercially available household cleanser. Ensure that no water gets inside the equipment to prevent possible shorts and damage to the equipment. 2. Introduction The sound level calibrator PeakTech® 8010 meets the requirements of EN 60942: 2003 Class 2, which is used to check the accuracy of sound level meters. A defined sound level signal with a sound level of 94 dB (decibels) or 114 dB at a sound frequency of 1000Hz can be generated.
3. Front and Panel Description 1 2 3 1. 2. 3.
4. Measurement Operation 1. Insert the microphone of your sound level meter in the calibration port of the PeakTech 8010. Make sure that the microphone is fully inserted into the calibration port. 2. Select the required sound level for testing (94 or 114dB). 3. Now read the measured value on the display of your sound level meter from. 4. If the measured value does not match with the calibration signal, you can readjust the sound level meter.
6. Replacing the battery If no sound pressure level output, then the battery needs to be replaced. For changing the battery please follow these steps: 1. Loosen the screw of the battery compartment cover on the back and remove the cover from the battery compartment, 2. disconnect the old battery from the battery cable and remove the old battery from the battery compartment, 3. Connect the new 9 V battery to the battery cable and replace battery in the battery compartment 4.
Statutory Notification about the Battery Regulations The delivery of many devices includes batteries, which for example serve to operate the remote control. There also could be batteries or accumulators built into the device itself. In connection with the sale of these batteries or accumulators, we are obliged under the Battery Regulations to notify our customers of the following: Please dispose of old batteries at a council collection point or return them to a local shop at no cost.
All rights, also for this translation, reprinting and copy of this manual or parts are reserved. Reproduction of all kinds (photocopy, microfilm or other) only by written permission of the publisher. This manual is according the latest technical knowing. Technical changing which are in the interest of progress reserved. We herewith confirm that the unit is calibrated by the factory according to the specifications as per the technical specifications. We recommend to calibrate the unit again, after 1 year.