DM 112 ™ Powered Speaker System Operating Manual www.peavey.
FCC/ICES Compliancy Statement This device complies with Part 15 of the FCC rules and Industry Canada license‐exempt RSS Standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, that may cause undesired operation. Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de licence.
ENGLISH Introduction Thank you for purchasing the powered Peavey® DM™ 112 powered speaker system. The DM™112 features a reliable bi-amped power section that provides a total of 660 Watts of peak available dynamic power with signal compression to prevent audible overload. The analog power amplifiers and linear power supply are coupled with a DSP based crossover and EQ. The LCD display and EQ presets along with other operating parameters are accessed via a one-knob selector.
smooth, even response, low distortion and good high frequency dispersion. Advanced Digital Signal Processing (A.D.S.P.) provides the crossover function, driver limiting, as well as the driver EQ to enable the speaker system to provide an accurate and neutral sound for any type of music. The DSP processing uses 64 bit double-precision to insure accurate and transparent sound processing, and the input/ output sections use a 96 kHz sampling rate at 24 bits for maximum fidelity.
LOWER REAR PANEL BOTTOM OF REAR PANEL 1 4 2 3 ON-OFF SWITCH (1) This rocker switch supplies AC power to the DM™115 when switched to the ON position. The ON position is with the left side of the switch pushed FUSE (1)“in” or nearly flush with the rear panel. The unit is AC power line fuse protected from overloads and fault conditions with FUSE (2) a slow-blow 5 x 20mm 250V fuse.
properly grounded. VOLTAGE SELECTOR SWITCH (4) The DM™112 has a voltage selector switch to allow switching between an input power voltage of 120VAC to a range from 220VAC to 240VAC, all at either 50 or 60 cycles per second (Hz). It should be set to the proper voltage for your country out of the box. However, world conditions are such that some areas have power line voltages differing from the voltage used by the majority of any given locale.
UPPER REAR PANEL 11 6 12 7 8 9 5 10 INPUT (5) The line-level input is of the medium impedance balanced type. The jack is a combo female XLR and 1/4" TRS connector. Sensitivity of this input is 0.39 volts for full output, when the MIC/LINE switch (7) is in the LINE position GAIN (6) Controls the gain or output level of the input signal. It is used to directly set the system output level for a given input signal.
UPPER REAR PANEL Push-To-Select button (12) Rotary knob that allow the user to select and choose menu options on the LCD display screen (11). Pushing the button in till it detents makes a menu choice. OPERATING INSTRUCTIONS Cautions The unit must be disconnected from the AC power source before any work is done on it. Refer all servicing to qualified service personnel. The back plate can become hot to the touch. Do not block or cover the fan or the exhaust louvers from ventilation.
Use of the DM™112 with a Speaker Stand The DM™112 has a stand mount cup molded-in so that the system can be stand mounted on a standard 1 3/8” (36mm) diameter stand pole. When using stands or poles, be sure to follow these precautions: A. Check the stand or pole specs to make sure that it can support the weight of the DM™112 (35 lbs./15.9 kg), and observe all safety precautions stated by the stand manufacturer, including the maximum height the stand is rated for. B.
If the mixing board indicates clipping of its output signals, then all of the DM™112 power capability is not being utilized cleanly. Clipping the signal before it gets to the DM™112 is not optimal. Reduce the mixer output level and turn up the Gain control on the DM™112. The amplifiers in the DM™112 are equipped with “Soft Limiting” circuitry and the LED indicator will show when DM™112 DDT™ has engaged.
If the default LCD message display is present (e.g. DM 112 and 01: EDM ), then push in the "Push-to-Select" knob to bring up the menu, which will display the first choice of " Recall preset ". 1. If you have selected " Recall preset " to select a different preset, then push the "Push-to-Select" knob to be able to rotate through the preset choices. An arrow symbol will appear at the left hand margin on the second line. You can now rotate the "Push-to-Select" knob to access the other preset choices.
” process over again. You can save a Factory Preset without any changes, and just re-name it, but it must be saved in one of the User Preset locations (11 thru 32). The Factory Presets in locations 01 through 10 are permanently saved at those locations The saved preset is one of the Factory Presets with the added menu item changes on top of that original factory preset, and what is saved is the current set of DSP parameters.
Ensure that shielded cables have been used to route the signal to the DM™112’s input. If speaker cables with 1/4" plugs are used as input cables instead of shielded cables, they will be prone to hum or buzz. Hum may be ground loop related. It may be helpful to lift the shield ground (Pin #1) on a balanced cable at the DM™112 end. Check any input changes carefully by first turning down the Level control, before plugging and unplugging cables, or lifting the shield ground at the speaker end.
Touchup For an overall finish enhancement and protective coating, use gloves to apply a plastic finish protector, such as Armor-All® protectant or a similar product, to the surface of the plastic cabinet only. Note that the cabinet will be slippery after these treatments; rub them down vigorously with a dry, lint-free cloth to minimize this.
SPECIFICATIONS Frequency Response: 68 Hz to 19 kHz, +/- 6 dB, anechoic environment Usable Low Frequency limit (-10 dB point anechoic): 55 Hz Nominal sensitivity (1W @1M, swept sine input in anechoic environment): 96 dB (average) Maximum Sound Pressure Level (1 meter): 124 dB SPL peak with music Radiation Angle measured at -6 dB point of polar response: Nominal: 110 degrees horizontal X 80 degrees vertical (Axis of the vertical main polar lobe is angled down 10 degrees, resulting in the angular pattern with
Overall Dimensions ( H x W x D ) 25.3”H x 14.38”W x 14.00”D 643 mm x 366 mm x 356 mm Weight: 35 lbs. (15.9 kg) ELECTRONICS AND AMPLIFIER SPECIFICATIONS: Internal power amplifiers (@120 VAC line): Total of 660 watts peak dynamic power Woofer - 410 watts peak dynamic power Continuous Power: 125 watts @ less than 1% distortion Tweeter - 250 watts peak dynamic power Continuous Power: 80 watts @ less than 1% distortion.
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: 11/01/2011 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.
U.S. customer warranty registration. Logo referenced in Directive 2002/96/EC Annex IV (OJ(L)37/38,13.02.
FROM: Place Postage Here Peavey Electronics Corporation Attn: Warranty Department PO Box 1150 Meridian, Ms 39305
