Envoy® 110 & Bandit® 112 TransTube® Series Amplifiers Operating Manual www.peavey.
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of electrical shock — DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.
WICHTIGE SICHERHEITSHINWEISE ACHTUNG: Beim Einsatz von Elektrogeräten müssen u.a. grundlegende Vorsichtsmaßnahmen befolgt werden: 1. Lesen Sie sich diese Anweisungen durch. 2. Bewahren Sie diese Anweisungen auf. 3. Beachten Sie alle Warnungen. 4. Befolgen Sie alle Anweisungen. 5. Setzen Sie dieses Gerät nicht in der Nähe von Wasser ein. 6. Reinigen Sie es nur mit einem trockenen Tuch. 7. Blockieren Sie keine der Lüftungsöffnungen. Führen Sie die Installation gemäß den Anweisungen des Herstellers durch. 8.
INSTRUCTIONS IMPORTANTES DE SECURITE ATTENTION: L’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Lire ces instructions. Gardez ce manuel pour de futures références. Prétez attention aux messages de précautions de ce manuel. Suivez ces instructions. N’utilisez pas cette unité proche de plans d’eau. N’utilisez qu’un tissu sec pour le nettoyage de votre unité.
INSTRUCCIONES IMPORTANTES PARA SU SEGURIDAD CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Guarde estas instrucciones. Haga caso de todos los consejos. Siga todas las instrucciones. No usar este aparato cerca del agua. Limpiar solamente con una tela seca. No bloquear ninguna de las salidas de ventilación.
ENGLISH Envoy® 110 and Bandit® 112 TransTube® Series Instrument Amplifiers So, you are the owner of a new Peavey TransTube Series instrument amplifier. Congratulations! Whether you are a beginner or seasoned pro, you could not have found a more practical, feature-packed amplifier. Peavey’s patented TransTube circuitry has moved forward into the third generation of products, leading the industry in tube emulation.
Front Panel 1 3 2 1 2 3 4 4 5 5 6 6 7 7 1 HIGH GAIN INPUT Used for most electric guitars. The High Gain Input is 6 dB louder than the Low Gain Input (2). 2 LOW GAIN INPUT Provided for instruments with extremely high outputs, which can result in overdriving (distorting) the High Gain Input (1). If both inputs are used simultaneously, their levels are both Low Gain. 3 VOLUME This control sets the volume level for the Clean channel.
Front Panel 8 8 9 9 10 11 10 11 12 12 13 13 14 8 CLASSIC/MODERN/HIGH GAIN - SWITCH This switch changes both the gain and voicing of the Lead channel. The MODERN setting increases the overall gain and notches (cuts) the mid frequencies, establishing a modern tone often associated with Hard Rock and Metal styles. The CLASSIC setting emulates overdriven tube sounds of the past.
Rear Panel 15 15 15 14 16 17 17 AC POWER INLET (Power Cord Located Under Chassis) This is the receptacle for an IEC line cord, which provides AC power tot the unit. Connect the line cord to this connector to provide power to the unit. Damage to the equipment may result if improper line voltage is used. (See voltage marking on unit.) Never break off the ground pin on any equipment. It is provided for your safety.
Rear Panel 22 18 19 20 21 22 18 POWER LEVEL (Bandit 112 ONLY) This switch provides three power level options: 25%, 50% and 100%. This circuit is actually a patented tube power amplifier simulator that "squashes" the signal. Use as desired for different playing environments, for example an apartment at 25% or live big at 100%. 19 EXTERNAL SPEAKER JACK (Bandit 112 ONLY) This 1/4” jack is provided for the connection of an external speaker cabinet. The minimum external speaker impedance is 8 ohms.
Suggested Settings Clean/Metal Clean Clean Channel: Jazz/Moderate Distortion Volume: As Desired Classic Clean/Metal Low: 7-9 Mid: 2-4 High: 5-7 Clean Blues/Dirty Blues Jazz Jazz/Moderate Distortion Clean/Metal Metal Lead Channel: Master Section: Pre Gain: 8-10 High Gain/ModerateClassic: Moderate Low: 8-10 Mid: 0-2 High: 6-8 Post Gain: As Desired Reverb: As Desired Boost: As Desired for solo level Moderate Distortion Clean Channel: Jazz/Moderate Distortion Volume: As Desired Classic Cl
Series Specifications Envoy® 110 Power Amplifier Section: Power @ Clipping (Typically): (1 kHz, 120 VAC line) 40 W RMS into 6 Ω Frequency Response: +0, -2 dB 100 Hz to 20 kHz @ 35 W RMS into 6 Ω Hum and Noise: Greater than 86 dB below rated power Power Consumption: (Domestic) Headphone Output: Load Impedance: 16 Ω or greater 0.3 W RMS System Hum & Noise @ Nominal Input Level: (20 Hz to 20 kHz unweighted) Greater than 78 dB below rated power Dimensions (H x W x D): 17" x 19.375" x 9.250" 43.
Series Specifications Bandit® 112 Power Amplifier Section: Rated Power and Load: Power specs measured with Power Level @ 100% 80 W RMS into 8 Ω 100 W RMS into 4 Ω Power @ Clipping (Typically): (1 kHz, 120 VAC line) 80 W RMS into 8 Ω 100 W RMS into 4 Ω Effects Send: Equalization: Load Impedance: 1 k Ω or greater Nominal Output Level: -5.4 dBV, 535 mV RMS Special Low, Mid, and High passive type EQ. Effects Return: Load Impedance: High Z, 22 k Ω Designed Input Level: -5.
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: July 1, 1998 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.
Features and specifications subject to change without notice. Peavey Electronics Corporation • 711 A Street • Meridian, MS 39301 (601) 483-5365 • FAX (601) 486-1278 • www.peavey.
