PV™i 8B+ 350-Watt, 8-Channel Mixer Amplifier Operating Manual www.peavey.
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of electrical shock — DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.
INSTRUCCIONES IMPORTANTES PARA SU SEGURIDAD CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Guarde estas instrucciones. Haga caso de todos los consejos. Siga todas las instrucciones. No usar este aparato cerca del agua. Limpiar solamente con una tela seca. No bloquear ninguna de las salidas de ventilación.
ENGLISH PV™i 8B+ 350-Watt, 8-Channel Mixer Amplifier The PVi 8B+ powered mixer is easy to use and transport, and is designed with the latest Peavey technology. Constructed with a rugged metal structure, wood cabinet, vinyl surface and protective corners, the PVi 8B+ is the ideal powered mixer. From packaging to quality control, we produce a product of maximum quality and efficiency with the same specifications you see on other, more expensive powered mixers.
Front Panel Rear Panel
Front Panel (1) 3-PIN LOW-IMPEDANCE MICROPHONE INPUT This input is for typical balanced, low-impedance microphones. It will automatically provide phantom power (15V) for condenser mics or active direct boxes. This has an input impedance of 1k ohms. The connector is wired as: Pin 1=shield; Pin 2=positive (hot); Pin 3=negative (cold).
Front Panel (17) MONITOR EQ This is the 7-band EQ with level meter. 17 (18) EFFECTS RETURN/MONITOR This controls the level of effects applied to the monitors. (19) MONITOR MIX LEVEL This controls the monitor output level at the Monitor Output Jack (29). 18 (20) MAIN EQ These are used to adjust the overall EQ of the master mix.
Rear Panel 5 4 3 2 1 (1) SPEAKER OUTPUTS These are four two-conductor 1/4" speaker outputs. Each one is rated at 4 ohms minimum impedance. Total minimum load for each amplifier channel is 4 ohms, except Bridged which is 8 ohms. You may connect either one 4-ohm (except Bridged), one 8-ohm or two 8-ohm speakers per output jack. Do not operate below rated minimum impedance. For maximum power transfer, be sure to use speaker cables and not instrument cables to connect to the speakers.
PV™i 8B+ SPECIFICATIONS Output Power: 350 watts / 4 ohms, music power 220 watts / 8 ohms, music power 250 watts / 4 ohms, continuous 150 watts / 8 ohms, continuous 650 watts / 8 ohms, Bridged Master Graphic Equalization: 63 Hz: +/- 12 dB 160 Hz: +/- 12 dB 400 Hz: +/- 12 dB 2.5 kHz: +/- 12 dB 6.
Notes: 11
Features and specifications subject to change without notice. Peavey Electronics Corporation • 5022 Hartley Peavey Drive • Meridian, MS • 39305 (601) 483-5365 • FAX (601) 486-1278 • www.peavey.