Electronics Industrial Contractor Amplifier Operating Guide

ManualsBrandsPeavey ManualsMusic MixerICA 600

ICA

™

SERIES

INDUSTRIAL CONTRACTOR AMPLIFIERS

OPERATING GUIDE

Summary of content (64 pages)

PAGE 1
ICA™ SERIES INDUSTRIAL CONTRACTOR AMPLIFIERS O P E R AT I N G G U I D E
PAGE 2
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of electrical shock — DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.
PAGE 3
TABLE OF CONTENTS Page INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION AND MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 BASIC SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
ENGLISH INTRODUCTION Congratulations on your purchase of an Architectural Acoustics ICA™ (Industrial Contractor Amplifier) from Peavey Electronics. Please read this manual carefully, especially the IMPORTANT SAFETY INSTRUCTIONS on page 18. It contains information vital to safe operation of the power amplifier. Also, please fill out and return the enclosed product registration card. ICA Series amplifiers represent new levels of value and flexibility never before offered to the contracting market.
PAGE 5
FRONT PANEL FEATURES RCHITECTURAL TM 600 INDUSTRIAL CONTRACTOR AMPLIFIER POWER A SIGNAL B CLIP LFCTM COUSTICS TM PROTECT POWER STANDBY OFF ON by 4 5 6 7 2 3 1 1. RACK MOUNTING EARS These mounting holes are provided on each front mounting ear. 2. 3-POSITION AC POWER SWITCH A 3-position switch is on the front panel. Sequential remote turn-on capability is a standard feature. With the switch pushed towards the outside position, the amplifier is ON.
PAGE 6
BACK PANEL FEATURES 10 11 9 12 13 8 8. INPUT SECTION The ICA™ Series comes standard with plugable input connectors and individual channel rotary attenuators. Connections at the input connector permit the audio signal ground to be connected or lifted from the chassis ground. 9. OUTPUT BARRIER STRIP A barrier strip is provided for connection of loudspeakers with bare wire or spade lug connectors. This barrier strip can accommodate up to two 10-gauge wires per terminal. 10.
PAGE 7
connecting the ENABLE OUT to the ENABLE IN of the next amplifier. A mating connector is shipped with the amplifier. 13. FAN GRILL A continuously variable-speed DC fan supplies cool air into the amplifier. Do not block this intake! The fan operates only when the amplifier heat sinks require cooling. OPERATION AC MAINS CIRCUIT SIZE REQUIREMENTS Power requirements for ICA™ amplifiers are rated at “idle”, 1/8 power (“typical” music conditions), 1/3 power, and maximum rated power.
PAGE 8
SIGNAL MODE CONFIGURATION ICA™ Series amplifiers are configured for Stereo (2-channel), Bridged Mode, or Parallel Mode operation at the input connector. To send the same signal to both channels (Parallel Mode), connect the input signal to CHANNEL A via the input connector. Run jumpers from the positive and negative terminals of the CHANNEL A input connector to the respective terminals of CHANNEL B. Both channels then share the CHANNEL A input signal but will operate independently.
PAGE 9
BRIDGED MODE DIAGRAM RCHITECTURAL TM 600 COUSTICS TM INDUSTRIAL CONTRACTOR AMPLIFIER 120 VAC 60 Hz 700 WATTS CAUTION by OUTPUT B OUTPUT A CLASS 2 WIRING OUTPUT POWER @ 4 OHMS IS 300 WAT TS/CH -6 -6 -3 -10 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
PAGE 10
FADE-IN PROTECTION This feature operates every time the amplifier is turned on, or after a protect condition. During turn on, the amplifier goes into protect mode and leaves the speaker load disconnected until the amplifier determines that the operating status is normal. The Fade-In circuit attenuates the signal during the initial turn on or protect operation. After relay release, channel gain gradually increases to the attenuator setting to avoid unnecessary stress on the loudspeakers.
PAGE 11
WIRE GAUGE CHART Stranded Power Power Power Cable Wire Loss Loss Loss Length Gauge Into Into Into (Feet) (AWG) 8 ohms 4 ohms 2 ohms ______________________________________________________ 5' 10' 40' 18 AWG .79% 1.58% 3.16% 16 .5 1.0 2.0 14 .31 .62 1.24 12 .20 .40 .80 10 .125 .25 .50 18 AWG 1.58% 3.16% 6.32% 16 1.0 2.0 4.00 14 .62 1.25 2.50 12 .40 .80 1.6 10 .25 .50 1.0 18 AWG 8.0% 12.6% 16 4.0 8.0 16.0 14 2.5 5.0 10.0 12 1.60 3.2 6.4 10 1.0 2.0 4.
PAGE 12
ICA™ 600 SPECIFICATIONS Rated Power (2 X 4 ohms): 300 watts @ 20 Hz - 20 kHz, both channels driven at < 0.1% THD Rated Power (2 x 8 ohms): 200 watts @ 20 Hz - 20 kHz at < 0.05% THD Rated Power (1 x 4 ohms): 360 watts @ 1 kHz at < 0.015% THD Rated Power (1 x 8 ohms): 275 watts @ 1 kHz at < 0.005% THD Minimum Load Impedance: 4 ohms Maximum RMS Voltage Swing: 57 volts Frequency Response: 10 Hz - 25 kHz; +0, -3 dB at 1 watt Power Bandwidth: 10 Hz - 100 kHz; +0, -3 dB at rated power THD (2 x 4 ohms): <0.
PAGE 13
ICA™ 1200 SPECIFICATIONS Rated Power (2 X 4 ohms): 600 watts @ 20 Hz - 20 kHz, both channels driven at < 0.1% THD Rated Power (2 X 8 ohms): 400 watts @ 20 Hz - 20 kHz, both channels driven at < 0.05% THD Rated Power (1 X 4 ohms): 700 watts @ 1 kHz at < 0.008% THD Rated Power (1 X 8 ohms): 425 watts @ 1 kHz at < 0.
PAGE 14
ICA™ 2400 SPECIFICATIONS Rated Power (2 x 4 ohms): 1200 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD SMPTE IMD: <0.1% 60 Hz and 7 kHz, 800 W @ 8 ohms Rated Power (2 x 8 ohms): 800 watts @ 20 Hz – 20 kHz both channels driven at < 0.08% THD Slew Rate: 35 V/us Rated Power (1 x 4 ohms): 1325 watts @ 1 kHz at < 0.08% THD Rated Power (1 x 8 ohms): 830 watts @ 1 kHz at < 0.
PAGE 15
ICA™ 400V SPECIFICATIONS Rated Power (two channels): 200 watts @ 20 Hz - 20 kHz both channels driven at <0.1% THD Rated Power (one channel): 215 watts @ 1 kHz at <0.0075% THD Minimum Load Impedance: ICA 400V-70: 25 ohms ICA 400V-100: 50 ohms Maximum RMS Voltage Swing: ICA 400V-70: 86 volts ICA 400V-100: 116 volts Input CMRR: > -65 dB @ 1 kHz Voltage Gain: x40 (32 dB) Input Sensitivity: ICA 400V-70: 1.77 volts for rated output ICA 400V-100: 2.
PAGE 16
ICA™ 800V SPECIFICATIONS Rated Power (two channels): 400 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD Rated Power (one channel): 415 watts @ 1 kHz at < 0.01% THD Minimum Load Impedance: ICA 800V-70: 12.
PAGE 17
ICA™ 2400V SPECIFICATIONS Rated Power (2 x 4 ohms): 1200 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD Rated Power (2 x 8 ohms): 800 watts @ 20 Hz – 20 kHz both channels driven at < 0.08% THD Rated Power (1 x 4 ohms): 1325 watts @ 1 kHz at < 0.08% THD Rated Power (1 x 8 ohms): 830 watts @ 1 kHz at < 0.08% THD Topology: Class H Minimum Load Impedance: 4 ohms Maximum RMS Voltage Swing: 95 volts Frequency Response: 10 Hz – 25 kHz; +0, -.
PAGE 18
ESPAÑOL INTRODUCCIÓN Felicidades en su compra de un amplificador de Acústica Arquitectónica ICA™ (Amplificador de Contratistas Acústicos por sus siglas en Inglés) de Peavey Electronics. Por favor lea este manual con atención, especialmente la seccione de SEGURIDAD en la página 18. Esta contiene información vital para la operación segura del amplificador. Por favor tómese el tiempo de llenar y mandar su tarjeta de registro del producto.
PAGE 19
4. Lleve a cabo las conexiones de poder, cubriendo las necesidades del amplificador. Vea las secciones CONECTOR IEC y Requisitos de los circuitos de CA para más información. 5. Gire el interruptor de poder (AC POWER) de tres posiciones a la posición ON y suba los atenuadores de ganancia (LEVEL) en el panel trasero a los niveles deseados.
PAGE 20
CARACTERÍSTICAS DEL PANEL TRASERO 10 11 9 RCHITECTURAL TM 600 COUSTICS TM INDUSTRIAL CONTRACTOR AMPLIFIER 220/240~ VAC 50/60 Hz 700 WATTS CAUTION by OUTPUT B OUTPUT A CLASS 2 WIRING OUTPUT POWER @ 4 OHMS IS 300 WATTS/CH -6 -6 -3 -10 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
PAGE 21
OPERACIÓN REQUISITOS DE TAMAÑO DE CIRCUITO DE CA Los requisitos de poder para los amplificadores ICA™ han sido calculados en estado “Idle”, a 1/8 de poder (condiciones de música ‘típicas’), 1/3 de poder y poder máximo. El máximo de poder requerido es limitado por el interruptor (breaker) del circuito. Consulte las fichas de especificaciones para conocer las necesidades de corriente de cada amplificador.
PAGE 22
Ahora los dos canales comparten la señal del CANAL A, pero operarán independientemente. Las bocinas son conectadas en modo estéreo. El Modo “Puenteado” (Bridged) convierte el amplificador en una unidad de un solo canal con una capacidad de poder igual a la suma de los dos canales, y con una carga del doble que la de un solo canal. En Modo Puenteado los canales operan con polaridades opuestas entre ellos para que un canal ‘empuje’ mientras que el otro ‘jala’ al mismo nivel.
PAGE 23
DIAGRAMA DE MODO PUENTEADO RCHITECTURAL TM 600 COUSTICS TM INDUSTRIAL CONTRACTOR AMPLIFIER 120 VAC 60 Hz 700 WATTS CAUTION by OUTPUT B OUTPUT A CLASS 2 WIRING OUTPUT POWER @ 4 OHMS IS 300 WAT TS/CH -6 -6 -3 -10 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
PAGE 24
PROTECCIÓN DE FADE-IN Esta función se activa cada vez que el amplificador es encendido, o después de una condición de protección. Al encenderlo, el amplificador automáticamente se encuentra en modo de protección y mantiene las cargas a las bocinas desconectadas hasta que el amplificador determina que el modo de operación es normal. La protección de Fade-In atenúa la señal durante el proceso inicial de encendido para proteger su operación.
PAGE 25
FICHA DE MEDIDAS DE CABLES Medida Poder Poder Poder Longitud de cables Perdido Perdido Perdido De cable Aislados a a a (pies) (AWG) 8 ohmios 4 ohmios 2 ohmios ______________________________________________________ 5' 10' 40' 18 AWG .79% 1.58% 3.16% 16 .5 1.0 2.0 14 .31 .62 1.24 12 .20 .40 .80 10 .125 .25 .50 18 AWG 1.58% 3.16% 6.32% 16 1.0 2.0 4.00 14 .62 1.25 2.50 12 .40 .80 1.6 10 .25 .50 1.0 18 AWG 8.0% 12.6% 16 4.0 8.0 16.0 14 2.5 5.0 10.0 12 1.
PAGE 26
Especificaciones del ICA™ 600 Poder Medido (2 X 4 ohmios): 300 watts @ 20 Hz - 20 kHz, Los dos canales a < 0.1% THD (Distorsión Total Armónica) Poder Medido (2 x 8 ohmios): 200 watts @ 20 Hz - 20 kHz a < 0.05% THD Poder Medido (1 x 4 ohmios): 360 watts @ 1 kHz at < 0.015% THD Factor de Reducción (damping) (8 ohmios): >450:1 @ 20 Hz - 1 kHz Enframiento: Ventilador de CD de 80 mm, apagado hasta 45° C, luego velocidad variable.
PAGE 27
Especificaciones del ICA™ 1200 Poder Medido (2 X 4 ohmios): 600 watts @ 20 Hz - 20 kHz, Los dos canales a < 0.1% THD (Distorsión Total Armónica) Poder Medido (2 x 8 ohmios): 400 watts @ 20 Hz - 20 kHz a < 0.05% THD Razón de Slew: 30 V/µs Factor de Reducción (damping) (8 ohmios): >350:1 @ 20 Hz - 1 kHz Enframiento: Ventilador de CD de 120 mm, apagado hasta 45° C, luego velocidad variable. Entrada CMRR: >-65 dB @ 1 kHz Poder Medido (1 x 4 ohmios): 70 watts @ 1 kHz at < 0.
PAGE 28
Especificaciones del ICA™ 2400 Poder Medido (2 X 4 ohmios): 1200 Watts @ 20 Hz - 20 kHz, Los dos canales a < 0.1% THD (Distorsión Total Armónica) Poder Medido (2 x 8 ohmios): 800 Watts @ 20 Hz - 20 kHz a < 0.08% THD Poder Medido (1 x 4 ohmios): 1325 Watts @ 1 kHz at < 0.08% THD Poder Medido (1 x 8 ohmios): 830 Watts @ 1 kHz at < 0.
PAGE 29
Especificaciones del ICA™ 400V Poder Medido (dos canales): 200 watts @ 20 Hz - 20 kHz, Los dos canales a < 0.1% THD (Distorsión Total Armónica) Poder Medido (un canal): 215 watts @ 1 kHz a < 0.
PAGE 30
Especificaciones del ICA™ 800V Poder Medido (dos canales): 400 Watts @ 20 Hz - 20 kHz, Los dos canales a < 0.1% THD (Distorsión Total Armónica) Poder Medido (un canal): 415 Watts @ 1 kHz a < 0.01% THD Impedancia de Carga Mínima: ICA 800V-70: 12.
PAGE 31
Especificaciones del ICA™ 2400V Poder Medido (dos canales): 1200 watts @ 20 Hz - 20 kHz, Los dos canales a < 0.1% THD (Distorsión Total Armónica) Poder Medido (un canal): Esperando Resultados Topología: Clase H Impedancia de Carga Mínima: @ 70.7 volts 6.3 Ohms Máximo swing de voltaje RMS: 95 voltios Respuesta de Frecuencias: 10 Hz - 25 kHz; +0, -3 dB a 1 Watt Banda de Poder: 10 Hz - 50 kHz; +0, -3 dB a poder medido THD (Distorsión Total Armónica) (dos canales): <0.
PAGE 32
FRANÇAIS INTRODUCTION Félicitations d’avoir choisi un Architectural Acoustics ICA™ (Industrial Contractor Amplifier) de Peavey Electronics. Veuillez lire attentivement ce manuel, surtout les CONSIGNES DE SECURITE à la page 18, qui contiennent des informations essentielles pour le bon fonctionnement de votre amplificateur. De plus, veuillez remplir et nous retourner la Regitration Card fournie avec votre matériel.
PAGE 33
PANNEAU AVANT RCHITECTURAL TM 600 INDUSTRIAL CONTRACTOR AMPLIFIER POWER A SIGNAL B CLIP LFCTM COUSTICS TM PROTECT POWER STANDBY OFF ON by 4 5 6 7 3 2 1 1. PATTES DE FIXATION RACK Chaque unité possède un panneau avant au format Rack. 2. INTERRUPTEUR 3-POSITIONS D’ALIMENTATION La “Mise en Route-Arrêt séquentiel contrôlable à distance” est disponible sur tous les modèles.
PAGE 34
PANNEAU ARRIERE 10 11 9 RCHITECTURAL TM 600 COUSTICS TM INDUSTRIAL CONTRACTOR AMPLIFIER 220/240~ VAC 50/60 Hz 700 WATTS CAUTION by OUTPUT B OUTPUT A CLASS 2 WIRING OUTPUT POWER @ 4 OHMS IS 300 WATTS/CH -6 -6 -3 -10 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
PAGE 35
OPERATION ALIMENTATION ELECTRIQUE La consommation électrique des unités ICA™ est noté: “idle”(en veille), 1/8 puissance maximale (condition typique musicale), 1/3 puissance maximale, et puissance maximale. Cette dernière est limitée par la présence d’un disjoncteur. Consultez la feuille de spécificité pour connaître les besoins de votre unité. Le voltage doit être le même que celui annoté à l’arrière de votre unité. Les dommages causés par une alimentation inadaptée ne sont pas couverts par la garantie.
PAGE 36
des charges minimales de chaque canal. Chaque canal agit en inversion par rapport à l’autre, en connectant la pin (-) du canal A à la pin (+) du canal B et la pin (+) du canal A à la pin (-) du canal B. Le signal d’entrée est connecté normalement aux pin (+) et (-) du canal A. Les 2 contrôles de gain agiront sur la puissance du signal, et doivent être à la même valeur (de préférence 0dB). Les hautsparleurs sont connectés aux bornes (+) de chaque canal.
PAGE 37
BRIDGED MODE DIAGRAM RCHITECTURAL TM 600 COUSTICS TM INDUSTRIAL CONTRACTOR AMPLIFIER 120 VAC 60 Hz 700 WATTS CAUTION by OUTPUT B OUTPUT A CLASS 2 WIRING OUTPUT POWER @ 4 OHMS IS 300 WAT TS/CH -6 -6 -3 -10 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
PAGE 38
PROTECTION DE MISE EN ROUTE A chaque fois que l’unité est mise sous tension, ou après une restauration d’état de protection, celle-ci passera en mode protégé et laisse les hauts-parleurs déconnectés jusqu’à vérification des systèmes de protection. Une fois la vérification terminée, l’unité fermera le relai du signal, mais en atténuant le gain, et augmentera celui-ci progressivement jusqu’au niveau normal pour éviter tout dommage aux hauts-parleurs.
PAGE 39
WIRE GAUGE CHART Stranded Power Power Power Cable Wire Loss Loss Loss Length Gauge Into Into Into 2 8 ohms 4 ohms 2o (Feet) (mm ) ______________________________________________________ 5' 10' 40' 80' 1 .79% 1.58% 3.16% 1,5 .5 1.0 2.0 2,5 .31 .62 1.24 4 .20 .40 .80 6 .125 .25 .50 1 1.58% 3.16% 6.32% 1,5 1.0 2.0 4.00 2,5 .62 1.25 2.50 4 .40 .80 1.6 6 .25 .50 1.0 1 8.0% 12.6% 1,5 4.0 8.0 16.0 2,5 2.5 5.0 10.0 4 1.60 3.2 6.4 6 1.0 2.0 4.0 25.
PAGE 40
ICA™ 600 SPECIFICATIONS Rated Power (2 X 4 ohms): 300 watts @ 20 Hz - 20 kHz, both channels driven at < 0.1% THD Rated Power (2 x 8 ohms): 200 watts @ 20 Hz - 20 kHz at < 0.05% THD Rated Power (1 x 4 ohms): 360 watts @ 1 kHz at < 0.015% THD Rated Power (1 x 8 ohms): 275 watts @ 1 kHz at < 0.005% THD Minimum Load Impedance: 4 ohms Maximum RMS Voltage Swing: 57 volts Frequency Response: 10 Hz - 25 kHz; +0, -3 dB at 1 watt Power Bandwidth: 10 Hz - 100 kHz; +0, -3 dB at rated power THD (2 x 4 ohms): <0.
PAGE 41
ICA™ 1200 SPECIFICATIONS Rated Power (2 X 4 ohms): 600 watts @ 20 Hz - 20 kHz, both channels driven at < 0.1% THD Rated Power (2 X 8 ohms): 400 watts @ 20 Hz - 20 kHz, both channels driven at < 0.05% THD Rated Power (1 X 4 ohms): 70 watts @ 1 kHz at < 0.008% THD Rated Power (1 X 8 ohms): 425 watts @ 1 kHz at < 0.
PAGE 42
ICA™ 2400 SPECIFICATIONS Rated Power (2 x 4 ohms): 1200 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD SMPTE IMD: <0.1% 60 Hz and 7 kHz, 800 W @ 8 ohms Rated Power (2 x 8 ohms): 800 watts @ 20 Hz – 20 kHz both channels driven at < 0.08% THD Slew Rate: 35 V/us Rated Power (1 x 4 ohms): 1325 watts @ 1 kHz at < 0.08% THD Rated Power (1 x 8 ohms): 830 watts @ 1 kHz at < 0.
PAGE 43
ICA™ 400V SPECIFICATIONS Rated Power (two channels): 200 watts @ 20 Hz - 20 kHz both channels driven at <0.1% THD Rated Power (one channel): 215 watts @ 1 kHz at <0.0075% THD Minimum Load Impedance: ICA 400V-70: 25 ohms ICA 400V-100: 50 ohms Maximum RMS Voltage Swing: ICA 400V-70: 86 volts ICA 400V-100: 116 volts Input CMRR: > -65 dB @ 1 kHz Voltage Gain: x40 (32 dB) Input Sensitivity: ICA 400V-70: 1.77 volts for rated output ICA 400V-100: 2.
PAGE 44
ICA™ 800V SPECIFICATIONS Rated Power (two channels): 400 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD Rated Power (one channel): 415 watts @ 1 kHz at < 0.01% THD Minimum Load Impedance: ICA 800V-70: 12.
PAGE 45
ICA™ 2400V SPECIFICATIONS Rated Power (two channels): 1200 watts @ 20 Hz to 20 kHz both channels driven at < 0.1% THD Rated Power (one channel): Awaiting test results Topology: Class H Minimum Load Impedance: @ 70.7 volts 6.3 ohms Maximum RMS Voltage Swing: 95 volts Frequency Response: 10 Hz – 25 kHz; +0, -.3 dB at 1 watt Power Bandwidth: 10 Hz – 50 kHz; +0, -3 dB at rated power THD (two channels driven): <0.008% @ 800 W @ 1 kHz with both channels driven THD (one channel driven): <0.
PAGE 46
DEUTSCH EINLEITUNG Wir freuen uns, dass Sie sich für den Architectural Acoustics ICA (Industrial Contractor Amplifier) von Peavey Electronics entschieden haben. Bitte lesen Sie vor Inbetriebnahme des Geräts unbedingt die Bedienungsanleitung, insbesondere die SICHERHEITSHINWEISE auf der vorderen Umschlaginnenseite. Sie enthalten wichtige Hinweise zum Betrieb des Verstärkers. Jetzt ist auch der richtige Zeitpunkt, die beiliegende Registrierkarte auszufüllen und an Peavey Electronics zurück zu senden.
PAGE 47
3. Schließen Sie die Lautsprecher an die Ausgangs-Schraubklemmleiste an und beachten Sie dabei die unterschiedlichen Betriebsarten stereo, parallel und bridged mono. Weitere Informationen hierzu finden Sie im Kapitel LAUTSPRECHERANSCHLUSS. 4. Schließen Sie den Verstärker unter Beachtung der korrekten Spannung an das Stromnetz an. Weitere Informationen hierzu finden Sie in den Kapiteln EURO-NETZANSCHLUSS und LEISTUNGSBEDARF. 5.
PAGE 48
6. LFC-LED Jeder Kanal ist mit einer LFC-(Load Fault Correction-)LED ausgestattet, die aufleuchtet, sobald der Verstärker ausgangsseitig eine nicht korrekte Last erkennt. Über die interne Schutzschaltung wird in diesem Fall sofort der Wert für die Eingangsverstärkung (Channel Gain) reduziert, so dass der Verstärker mit einem bei der jeweiligen Last sicheren Pegel weiter arbeitet. Weitere Informationen hierzu finden Sie im Kapitel SCHUTZSCHALTUNGEN. 7.
PAGE 49
12. SEQUENTIELLE EIN/AUSSCHALT-FUNKTION Verstärker der ICA-Serie sind serienmäßig mit einer fernsteuerbaren, sequentiellen Ein/Ausschaltfunktion ausgestattet, die durch das Schalten des Netzschalters in den STANDBY-Modus aktiviert wird. Wird an der rückwärtigen, 4-poligen steckbaren Reihenklemme eine Spannung von 12 - 24 V DC erkannt, schaltet sich der Verstärker bei bestehender Verbindung des ENABLE-Anschlusses mit dem 24 V DC+-Anschluss automatisch ein.
PAGE 50
WÄRMEENTWICKLUNG Die speziellen Kühlungsanforderungen Ihres Systems sollte der jeweils zuständige Techniker am besten beurteilen können. Die Wärmewerte für Ihr(e) Verstärkermodell(e) finden Sie in den Technischen Daten hinten in dieser Bedienungsanleitung. EINGANGSMODUL Das Eingangsmodul ist auf symmetrische und unsymmetrische Verbindungen ausgelegt.
PAGE 51
PARALLEL-BETRIEB RCHITECTURAL TM 600 COUSTICS TM INDUSTRIAL CONTRACTOR AMPLIFIER 120 VAC 60 Hz 700 WATTS CAUTION by OUTPUT B OUTPUT A CLASS 2 WIRING OUTPUT POWER @ 4 OHMS IS 300 WATTS/CH -6 -6 -3 -10 WARNING: TO REDUCE THE RISK OF FIRE OR ENABLE IN 24V DC+ ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
PAGE 52
CLIP-LIMITER Wird der Verstärker unter Volllast – d.h. kurz vor dem Clipping (Übersteuern) – gefahren, sorgt der integrierte Clip-Limiter für eine automatische Reduktion der Eingangsverstärkung und schützt die Lautsprecher so gegen Überlastung und das kontinuierliche Auftreten schädigender Rechteckwellen. Angezeigt wird dies durch die CLIP-LED. Signalübliche Transienten lassen den Clip-Limiter jedoch nicht ansprechen, da dieser lediglich der Verhinderung massiver bzw. kontinuierlicher Übersteuerung dient.
PAGE 53
nächsten Verstärkers. Verstärker der ICA-Serie lassen sich parallel schalten (“durchschleifen”) und – durch Verbindung aller 24 V DC+- und COMMON-Anschlüsse miteinander – an die Steuerspannung anbinden. Beachten Sie, dass zur Initiierung des Einschaltvorgangs des ersten und sämtlicher nachfolgender Verstärker zwischen dem 24 V DC+-Terminal und dem ENABLE OUT-Anschluss des ersten Verstärkers ein einpoliger Schalter (SPST) erforderlich ist.
PAGE 54
WIRE GAUGE CHART Stranded Power Power Power Cable Wire Loss Loss Loss Length Gauge Into Into Into (Feet) (AWG) 8 ohms 4 ohms 2 ohms ______________________________________________________ 5' 10' 40' 18 AWG .79% 1.58% 3.16% 16 .5 1.0 2.0 14 .31 .62 1.24 12 .20 .40 .80 10 .125 .25 .50 18 AWG 1.58% 3.16% 6.32% 16 1.0 2.0 4.00 14 .62 1.25 2.50 12 .40 .80 1.6 10 .25 .50 1.0 18 AWG 8.0% 12.6% 16 4.0 8.0 16.0 14 2.5 5.0 10.0 12 1.60 3.2 6.4 10 1.0 2.0 4.
PAGE 55
ICA™ 600 SPECIFICATIONS Rated Power (2 X 4 ohms): 300 watts @ 20 Hz - 20 kHz, both channels driven at < 0.1% THD Rated Power (2 x 8 ohms): 200 watts @ 20 Hz - 20 kHz at < 0.05% THD Rated Power (1 x 4 ohms): 360 watts @ 1 kHz at < 0.015% THD Rated Power (1 x 8 ohms): 275 watts @ 1 kHz at < 0.005% THD Minimum Load Impedance: 4 ohms Maximum RMS Voltage Swing: 57 volts Frequency Response: 10 Hz - 25 kHz; +0, -3 dB at 1 watt Power Bandwidth: 10 Hz - 100 kHz; +0, -3 dB at rated power THD (2 x 4 ohms): <0.
PAGE 56
ICA™ 1200 SPECIFICATIONS Rated Power (2 X 4 ohms): 600 watts @ 20 Hz - 20 kHz, both channels driven at < 0.1% THD Rated Power (2 X 8 ohms): 400 watts @ 20 Hz - 20 kHz, both channels driven at < 0.05% THD Rated Power (1 X 4 ohms): 700 watts @ 1 kHz at < 0.008% THD Rated Power (1 X 8 ohms): 425 watts @ 1 kHz at < 0.
PAGE 57
ICA™ 2400 SPECIFICATIONS Rated Power (2 x 4 ohms): 1200 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD SMPTE IMD: <0.1% 60 Hz and 7 kHz, 800 W @ 8 ohms Rated Power (2 x 8 ohms): 800 watts @ 20 Hz – 20 kHz both channels driven at < 0.08% THD Slew Rate: 35 V/us Rated Power (1 x 4 ohms): 1325 watts @ 1 kHz at < 0.08% THD Rated Power (1 x 8 ohms): 830 watts @ 1 kHz at < 0.
PAGE 58
ICA™ 400V SPECIFICATIONS Rated Power (two channels): 200 watts @ 20 Hz - 20 kHz both channels driven at <0.1% THD Rated Power (one channel): 215 watts @ 1 kHz at <0.0075% THD Minimum Load Impedance: ICA 400V-70: 25 ohms ICA 400V-100: 50 ohms Maximum RMS Voltage Swing: ICA 400V-70: 86 volts ICA 400V-100: 116 volts Input CMRR: > -65 dB @ 1 kHz Voltage Gain: x40 (32 dB) Input Sensitivity: ICA 400V-70: 1.77 volts for rated output ICA 400V-100: 2.
PAGE 59
ICA™ 800V SPECIFICATIONS Rated Power (two channels): 400 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD Rated Power (one channel): 415 watts @ 1 kHz at < 0.01% THD Minimum Load Impedance: ICA 800V-70: 12.
PAGE 60
ICA™ 2400V SPECIFICATIONS Rated Power (2 x 4 ohms): 1200 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD Rated Power (2 x 8 ohms): 800 watts @ 20 Hz – 20 kHz both channels driven at < 0.08% THD Rated Power (1 x 4 ohms): 1325 watts @ 1 kHz at < 0.08% THD Rated Power (1 x 8 ohms): 830 watts @ 1 kHz at < 0.08% THD Topology: Class H Minimum Load Impedance: 4 ohms Maximum RMS Voltage Swing: 95 volts Frequency Response: 10 Hz – 25 kHz; +0, -.
PAGE 61
Notes: 61
PAGE 62
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: July 1, 1998 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.
PAGE 63
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric products, basic cautions should always be followed, including the following: 1. Read all safety and operating instructions before using this product. 2. All safety and operating instructions should be retained for future reference. 3. Obey all cautions in the operating instructions and on the back of the unit. 4. All operating instructions should be followed. 5. This product should not be used near water (i.e.
PAGE 64
Features and specifications subject to change without notice. Peavey Electronics Corporation • 711 A Street • Meridian • MS • 39301 (601) 483-5376 • FAX (601) 486-1678 • http://aa.peavey.com ©2001 80304800 Printed in the U.S.A.