P1BT/P2BT/P3BT Column ARRAY Specifications www.peavey.
FCC/ICES Compliancy Statement This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS Standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, that may cause undesired operation. Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de licence.
FCC Radiation Exposure Statement This equipment complied with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IC Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body.
SPECIFICATIONS P1BT/P2BT/P3BT Column Powered Speaker Systems Congratulations on purchasing the Peavey P1BT/P2BT/P3BT Powered Speaker System. These compact, portable and powerful systems are a perfect solution for the weekend warrior, singer songwriter or DJ. • Bluetooth stereo linking • Bluetooth audio input for streaming music from any Bluetooth device • 3 Channel mixer • 2 XLR mic inputs and 1/4" Line Inputs • RCA/3.
P1 BT Top Panel 12 13 PAIRING STEREO LINK 7 6 5 4 2 3 1 8 Subwoofer Out 5 IN OUT
Input Panel (1) XLR Mic Input (Ch 1&2) Use this XLR connector to connect a microphone to the P1/2/3BT speaker. P1 BT (2) Line Input (Ch 1&2) Use this 1/4" (6.5mm) connector to connect a line-level source to the P1/2/3BT speaker. The line input is typically used for sources like keyboards and CD players. (3) RCA and 3.5mm Input (Ch 3) PAIRING These inputs, RCA and 3.5mm (1/8") accept a stereo input from the output of an MP3 player, CD player, phone or similar device. STEREO LINK (4) 3.
Bluetooth (12) Bluetooth Pairing Use this button to link your Bluetooth source (phone, tablet, etc...) to the speaker. See Bluetooth operation below. (13) Bluetooth Stereo Link Use this button to link your speaker to second PB 1/2/3BT speaker. See Bluetooth operation below. Bluetooth Operation: Pairing: To pair your bluetooth source to the speaker, use the following steps: 1. Press mode button on the back of the speaker to make the speaker discoverable. The pair ing LED should start blinking.
Rear Panel 15 14 (14) Power Switch The power switch is used to turn the speaker on and off (15) AC Power Inlet This is the receptacle for an IEC line cord, which provides AC power to the unit. Connect the line cord to this connector to provide power to the unit. Damage to the equipment may result if improper line voltage is used. (See line voltage marking on unit). Never break off the ground pin on any equipment. It is provided for your safety.
Specifications Connections 2 - XLR input jacks (Ch 1&2) 2 - 1/4" (6.35mm) TRS input jacks (Ch 1&2) 1 - 1/8" (3.5mm) TRS/stereo input (Ch 3) 1 - RCA input (Ch 3) 2 - XLR SYNC (In/Out) 1 - 1/4" (6.
www.peavey.com Warranty registration and information for U.S. customers available online at www.peavey.com/warranty or use the QR tag below Features and specifications subject to change without notice. Peavey Electronics Corporation 10 5022 Hartley Peavey Drive Meridian, MS 39305 Logo referenced in Directive 2002/96/EC Annex IV (OJ(L)37/38,13.02.