® SANPERA™ I SANPERA I Player`s Handbook TM
® SANPERA™ I Welcome Thank you for purchasing the SanperaTM I foot controller for your VYPYR® amplifier. We are certain you will enjoy having the control of your VYPYR at your feet.
Note: Your SanperaTM I is powered by your VYPYR® amplifier and requires the special 8-pin MIDI cable included with your Sanpera in order to function correctly.
® SANPERA™ I The Sanpera I operates in three modes, Preset mode, Looper Mode and Bank Select mode. The functions of buttons 1-4 will vary depending on which mode you are in. 1 2 5 6 PRESET MODE When you first plug your Sanpera I into the amplifier (using the provided 8 pin MIDI cable) the pedal will default to PRESET mode. In this mode buttons 1-4 correspond with the four PRESET buttons on your VYPYR®.
1 2 5 6 BANK SELECT MODE 3 4 The Sanpera I allows you to access all three BANKS of presets found on your VYPYR® amplifier. To enter BANK SELECT mode, press buttons 1 and 2 simultaneously. Three LEDs will illuminate to indicate you are in BANK SELECT mode. Buttons 1, 2 and 3 now function as BANK SELECT buttons and have alternate labeling: BANK A, BANK B and BANK C. One of the three LEDs will be RED, indicating the BANK you currently have selected.
® SANPERA™ I LOOPER CONTROLS To enter LOOP mode, press buttons 3 and 4 simultaneously. Upon entering LOOP mode all active LEDs will change from red to green, indicating you are in LOOP mode. In the case, the Stompbox and Delay effects are set to OFF (See Looper controls items 1 and 2), you may not see any active LEDs upon entering LOOP mode. 3.
LOOPER CONTROLS 1 2 5 6 1. Stompbox On/Off In LOOP mode this button allows you the ability to turn on and off the STOMPBOX selected (if any) on your VYPYR® amplifier. If the corresponding LED is green, the effect is active; if the LED is off, the effect is also off. 2. Delay On/Off In LOOP mode this button allows you the ability to turn on and off the DELAY effect (if any) on your VYPYR amplifier. If the corresponding LED is green, the effect is active; if the LED is off, the effect is also off.
® 1 SANPERA™ I 2 5 6 5. Main/AUX Indication LED These LEDs indicate whether the pedal is in MAIN mode or Aux mode. Depress the toe area of the expression pedal to switch between modes. The default setting of the expression pedal is to control the volume of the amplifier. The Main LED indicates that the expression pedal is set to VOLUME, and AUX indicates WAH unless the amplifier is set to PITCH SHIFT. 6.
1 2 5 6 CALIBRATION MODE: 3 4 Occasionally it may be necessary to re-calibrate your expression pedal. To enter CALIBRATION mode hold button 4 and press button 1. Upon entering CALIBRATION mode the LED above button 1 will be green. This green LED indicates that you need to press button 1 after each step of the calibration process. Button 4 will be RED upon entering CALIBRATION mode and allows you to skip steps in the calibration process (normally not necessary).
® SANPERA™ I PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: September 5, 2007 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.
What Peavey Will Do We will repair or replace (at Peavey's discretion) products covered by warranty at no charge for labor or materials. If the product or component must be shipped to Peavey for warranty service, the consumer must pay initial shipping charges. If the repairs are covered by warranty, Peavey will pay the return shipping charges.
Peavey Electronics Corporation • 5022 Hartley Peavey Drive • Meridian, MS 39305 Phone: (601) 483-5365 • Fax: (601) 486-1278 • www.peavey.
