VB-2 ™ All-Tube Bass Amplifier Operating Manual www.peavey.
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of electrical shock — DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions. 8.
WICHTIGE SICHERHEITSHINWEISE ACHTUNG: Beim Einsatz von Elektrogeräten müssen u.a. grundlegende Vorsichtsmaßnahmen befolgt werden: 1. Lesen Sie sich diese Anweisungen durch. 2. Bewahren Sie diese Anweisungen auf. 3. Beachten Sie alle Warnungen. 4. Befolgen Sie alle Anweisungen. 5. Setzen Sie dieses Gerät nicht in der Nähe von Wasser ein. 6. Reinigen Sie es nur mit einem trockenen Tuch. 7. Blockieren Sie keine der Lüftungsöffnungen. Führen Sie die Installation gemäß den Anweisungen des Herstellers durch. 8.
INSTRUCTIONS IMPORTANTES DE SECURITE ATTENTION: L’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. Lire ces instructions. Gardez ce manuel pour de futures références. Prétez attention aux messages de précautions de ce manuel. Suivez ces instructions. N’utilisez pas cette unité proche de plans d’eau. N’utilisez qu’un tissu sec pour le nettoyage de votre unité.
INSTRUCCIONES IMPORTANTES PARA SU SEGURIDAD CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6. Limpiar solamente con una tela seca. 7. No bloquear ninguna de las salidas de ventilación. Instalar de acuerdo a las instrucciones del fabricante. 8.
ENGLISH VB-2™ All-Tube Bass Amplifier Congratulations on your purchase of the new VB-2™ bass amplifier from Peavey. Are you ready for bass tone? The Peavey VB-2™ all-tube bass amplifier is your one stop spot for fantastic bass tone, no matter what musical styles you play. The versatile preamp can give you tones ranging from squeaky clean hi-fi to vintage dub to aggressive metal. The VB-2™ utilizes a special, 3-band EQ that gives you the best of passive and active bass tone controls.
Front Panel 3 1 2 4 6 7 5 1 10 8 9 High Gain Input Input for passive basses. Tip: If you have an aggressive playing style and you use a passive bass, you may find that the LOW GAIN input will offer more clean headroom. 2 Low Gain Input Input for active basses, attenuated 6dB. 3 Mute/Tune Switch Mutes the output of the DI, the effects loop, and the output of the amp, but still allows you to use the TUNER jack on the rear of the amp.
Front Panel 12 13 11 11 17 14 15 16 18 19 High Control Active EQ control that cuts or boosts high frequencies. 12 Send Jack Output signal from the preamp that may be used to drive effects or a slave amplifier. 13 Return Jack Essentially, the input of the power amp that may serve as an input for effects or to drive the power amp as a slave amplifier from another preamp. 14 Master Volume Control Controls the power amplifier drive.
Rear Panel 20 22 21 24 23 20 26 25 IEC Power Port Your AC line cord plugs here. This is the standard IEC power connector. An AC main cord having the appropriate AC plug and rating for the intended operating voltage is included in the carton. U.S. Domestic AC Mains Cord The mains cord supplied with the unit is a heavy-duty, three conductor type with a conventional 120VAC plug with ground pin. It should be connected to an independent circuit capable of continuously supporting at least 15 amps.
Rear Panel 19 27 28 29 23 Impedance Select Switch The IMPEDANCE SELECT switch is located on the rear of the unit. There are output transformer taps for 2Ω, 4Ω and 8Ω (Ω=ohm) loads since they are the most common impedance requirements bass players run into. Using the correct setting is important for longer tube life and maximum performance. It's best if this switch is configured while the amp is on standby. Simply move the selector to the correct impedance setting.
VB-2 ™ Suggested Settings Suggested Settings For Modern: 1.) Rock: Low = 8 Mid = 3 Mid Shift = 800 High = 5 2.) Metal: Low = 10 Mid = 2 Mid Shift = 400 High = 8 Suggested Settings For Funk: 1.) Slap: Low = 8 Mid = 3 Mid Shift = 400 High = 6 2.
Suggested Settings For Classic: 1.) Rock: Low = 10 Mid = 3 Mid Shift = 600 High = 0 2.
VB-2 ™ SPECIFICATIONS Power Amplifier High Gain Input: 6 - EL34/6CA7 power tubes 1 - 12AT7 driver tube/phase splitter Input Impedance = 1Mohm Minimum Sensitivity = 18mVrms or -32.7dBu Normal Sensitivity = 41mVrms or -25.5dBu Rated Power: Low Gain Input: 225 watts continuous into 8, 4 or 2 ohms @ < 5% THD SENSITIVITY (RETURN jack) = 1.8Vrms or 7.32dBu Input Impedance = 68Kohm (Power amp rated with RESONANCE and PRESENCE set to "0") Minimum Sensitivity = 36mVrms or -26.
VB-2™ Functional Block Diagram
Tube Replacement Warning! Never use ANY power tube type other than EL34s or 6CA7s. Doing otherwise may result in damage to the amp, unpredictable performance and electric shock. Use or specify a matched sextet of EL34 or 6CA7 tubes. Have the bias set by a professional. This must be done every time ANY of the power tubes are replaced. If the bias is set wrong, the amp will not put out maximum power, the output will be more distorted, and the tubes may not last as long.
Notes: 17
Notes: 18
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: September 5, 2007 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.
Features and specifications subject to change without notice. Peavey Electronics Corporation 5022 Hartley Peavey Drive • Meridian, MS 39305 (601) 483-5365 • FAX (601) 486-1278 • www.peavey.