CS® 3000/4000/4080 HZ Power Amplifier Owner's Manual For more information on other great Peavey products, visit your local Peavey dealer or go online to www.peavey.
WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions. 8.
SICHERHEITSHINWEISEACHTUNG: Beim Einsatz von Elektrogeräten müssen u.a. grundlegende Vorsichtsmaßnahmen befolgt werden: 1. Lesen Sie sich diese Anweisungen durch. 2. Bewahren Sie diese Anweisungen auf. 3. Beachten Sie alle Warnungen. 4. Befolgen Sie alle Anweisungen. 5. Setzen Sie dieses Gerät nicht in der Nähe von Wasser ein. 6. Reinigen Sie es nur mit einem trockenen Tuch. 7. Blockieren Sie keine der Lüftungsöffnungen.
ATTENTION: L’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. Lire ces instructions. 2. Gardez ce manuel pour de futures références. 3. Prétez attention aux messages de précautions de ce manuel. 4. Suivez ces instructions. 5. N’utilisez pas cette unité proche de plans d’eau. 6. N’utilisez qu’un tissu sec pour le nettoyage de votre unité. 7.
CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6. Limpiar solamente con una tela seca. 7. No bloquear ninguna de las salidas de ventilación. Instalar de acuerdo a las instrucciones del fabricante. 8.
警告: 電気製品を使用するときは、次の項目を含め、基本的な注意事項を常にお守りください。 1. 本書の指示内容をお読みください。 2. 本書は保管してください。 3. すべての警告に注意してください。 4. すべての指示に従ってください。 5. 本装置を水の近くで使用しないでください。 6. お手入れには乾いた布をお使いください。 7. 開口部をふさがないでください。 メーカーの指示に従って設置してください。 8. ラジエータ、 ストーブなど (アンプを含む)、発熱体の近くに設置しないでください。 9. 分極プラグや接地プラグの安全性を損なわないようにしてください。分極プラグの2つのブレードは、一方が他より幅広くなっています。 接地式のプラグには2つのブレードと接地プラグがあります。幅広のブレードや接地プラグは安全のために付けられています。所定のプ ラグがコンセントなどに合わない場合、 旧式のコンセントなどの交換について技術者に問い合わせてください。 10.
Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. ENGLISH Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: Risk of electrical shock — DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.
ENGLISH CS® 3000/4000/4080 HZ Power Amplifiers Congratulations on your purchase of a Peavey CS Series power amplifier! Designed for years of reliable operation, CS Series amplifiers offer the sonic superiority and unsurpassed reliability for which Peavey is famous in a rugged, compact unit. Advanced technologies and extensive protection circuitry allow operation with greater efficiency, even under difficult loads and power conditions.
*OUSPEVDUJPO *OUSPEVDUJPO *OUSPEVDUJPO 0QFSBUJOH 1SFDBVUJPOT 0QFSBUJOH 1SFDBVUJPOT .BLF TVSF UIF NBJOT WPMUBHF JT DPSSFDU BOE JT UIF TBNF BT UIBU QSJOUFE PO UIF SFBS PG UIF BNQMJGJFS %BNBHF DBVTFE CZ .
Wire Guage Charts Stranded Cable Lgth. (ft.) Wire Gauge (AWG) Power Loss (8 ohm load) Power Loss (4 ohm load) Power Loss (2 ohm load) 5 18 16 14 12 10 0.81% 0.51 0.32 0.20 0.128 1.61% 1.02 0.64 0.40 0.25 3.2% 2.0 1.28 0.80 0.51 10 18 16 14 12 10 1.61% 1.02 0.64 0.40 0.25 3.2% 2.0 1.28 0.80 0.51 6.2% 4.0 2.5 1.60 1.01 40 18 16 14 12 10 8 6.2% 4.0 2.5 1.60 1.01 0.60 11.9% 7.7 5.0 3.2 2.0 1.20 22% 14.6 9.6 6.2 4.0 2.4 18 16 14 12 10 8 11.9% 7.7 5.0 3.2 2.0 1.20 22% 14.6 9.6 6.2 4.0 2.
Operation Modes Stereo Operation For stereo (dual channel) operation, turn the amplifier OFF and set the mode select switches on the back panel to the out (extended) position. In this mode, both channels operate independently of each other, with their input attenuators controlling their respective levels. Thus, a signal at channel A’s input produces an amplified signal at channel A’s output, while a signal at channel B’s input produces an amplified signal at channel B’s output.
'SPOU 1BOFM 'SPOU 1BOFM 3FBS 1BOFM 3FBS 1BOFM 4XJUDIFT $POUSPMT 4XJUDIFT $POUSPMT "$ 1PXFS 4XJUDI $JSDVJU #SFBLFS "$ 1PXFS 4XJUDI $JSDVJU #SFBLFS 5IF $4 4FSJFT BNQMJGJFST GFBUVSF B DPNCJOBUJPO "$ TXJUDI DJSDVJU CSFBLFS PO UIF GSPOU QBOFM *G UIF TXJUDI TIVUT PGG 5IF $4 4FSJFT BNQMJGJFST GFBUVSF B DPNCJOBUJPO "$ TXJUDI DJSDVJU CSFBLFS PO UIF GSPOU QBOFM *G UIF TXJUDI TIVUT PGG EVSJOH OPSNBM VTF QVTI JU CBDL UP UIF 0/ QPTJUJPO PODF *G UIF TXJUDI XJMM OPU TUBZ JO
Front Panel 3 1 2 3 1 2 Indicators CS® Series amplifiers feature three front panel LED indicators per channel: PWR (power), SIG (signal) and DDT™ (Distortion Detection Technique). These LED indicators inform the user of each channel’s operating status and warn of possible abnormal conditions. PWR LED (1) The Power LED indicates that the channel is operational. It illuminates under normal operation and remains on even when the channel’s DDT circuit is activated.
Protection Features The Peavey CS® Series incorporates several circuits to protect the amplifier and speakers under virtually any situation. Peavey has made the amplifiers as foolproof as possible by making them immune to short and open circuits, mismatched loads, DC voltage and overheating. If a channel goes into the DDT™ gain reduction mode, the DDT LED illuminates. The clipping percentage or output power is instantly reduced.
Protection Features RampUp™ Signal Control Whenever a CS® Series amplifier powers up or comes out of a protect mode, the RampUp circuit activates. While the speakers are disconnected, the RampUp circuit fully attenuates the signal and activates the DDT™ LED. After the output relay closes, the signal slowly and gradually raises up to its set level. The PWR LED will illuminate and the DDT LED will turn off when the signal is no longer attenuated.
Amplifier Maintenance and User Responsibility A CS Series amplifier requires no routine maintenance and should not need internal adjustment during its lifetime. Your CS Series amplifier is very powerful and can be potentially dangerous to loudspeakers and humans alike. It is your responsibility to read the Important Precautions section and to make sure that the amplifier is installed, wired and operated properly as instructed in this manual.
CS ® Series 3000/4000/4080 HZ Power Amplifiers SPECIFICATIONS CS 3000 CS 4000 CS 4080 HZ Rated Power Bridged 3,050 watts @ 1 kHz at <0.1% T.H.D. @ 4 ohms 4,000 watts @ 1 kHz at <0.1% T.H.D. @ 4 ohms 4,080 watts @ 1 kHz at <0.1% T.H.D. @ 8 ohms Rated Power 2 x 2 ohms 1,500 watts per channel @ 1 kHz <0.05% T.H.D. both channels driven 2,000 watts per channel @ 1 kHz <0.1% T.H.D. both channels driven N/A Rated Power 2 x 4 ohms 1,025 watts per channel @ 1 kHz at <0.05% T.H.D.
CS® Series SPECIFICATIONS CS 3000 CS 4000 CS 4080 HZ Slew Rate > 15V/us > 15V/us > 15V/us Damping Factor (8 ohms) > 500:1 @ 20 Hz - 1 kHz > 500:1 @ 20 Hz - 1 kHz > 500:1 @ 20 Hz - 1 kHz Phase Response +5 to - 15 degrees from 20 Hz to 20kHz +5 to - 12 degrees from 20 Hz to 20kHz +5 to - 12 degrees from 20 Hz to 20kHz Input Sensitivity 1.6 volts +/- 3% for 1 kHz. 4 ohms rated power, 1.37 volts +/- 3% for 1 kHz. 2 ohms rated power 1.84 volts +/- 3% for 1 kHz. 4 ohms rated power, 1.
DEUTSCH CS® 3000/4000/4080 HZ Endstufen Herzlichen Glückwunsch zum Kauf einer Endstufe der CS Series von Peavey! Die Verstärker der CS Series wurden für einen zuverlässigen Betrieb und lange Lebensdauer entwickelt. In einem robusten, kompakten Gerät bieten sie die überragende Schallleistung und die unübertroffene Zuverlässigkeit, für die Peavey bekannt ist.
&*/-&*56/( &*/-&*56/( 4JDIFSIFJUTIJOXFJTF GS EFO #FUSJFC "DIUFO 4JF EBSBVG EBTT EJF /FU[TQBOOVOH LPSSFLU JTU VOE NJU EFO "OHBCFO BVG EFS 3DLTFJUF EFT 7FSTUjSLFST 4JDIFSIFJUTIJOXFJTF GS EFO #FUSJFC CFSFJOTUJNNU 4DIjEFO EJF BVGHSVOE EFT "OTDIMVTTFT EFT 7FSTUjSLFST BO FJOF VOHFFJHOFUF 8FDITFMTQBOOVOH 4FSJFT (BSBOUJF BCHFEFDLU /jIFSF *OGPSNBUJPOFO [VS FSGPSEFSMJDIFO 4QBOOVOH FOUTUFIFO XFSEFO OJDIU WPO EFS $4 "DIUFO 4JF EBSBVG EBTT EJF /FU[TQBOOVOH LPSSFLU JTU VOE NJU EFO "OHBCFO BVG EFS 3DLTFJ
Kabelstärkentabellen Stranded Cable Lgth. (ft.) Wire Gauge (AWG) Power Loss (8 ohm load) Power Loss (4 ohm load) Power Loss (2 ohm load) 5 18 16 14 12 10 0.81% 0.51 0.32 0.20 0.128 1.61% 1.02 0.64 0.40 0.25 3.2% 2.0 1.28 0.80 0.51 10 18 16 14 12 10 1.61% 1.02 0.64 0.40 0.25 3.2% 2.0 1.28 0.80 0.51 6.2% 4.0 2.5 1.60 1.01 40 18 16 14 12 10 8 6.2% 4.0 2.5 1.60 1.01 0.60 11.9% 7.7 5.0 3.2 2.0 1.20 22% 14.6 9.6 6.2 4.0 2.4 18 16 14 12 10 8 11.9% 7.7 5.0 3.2 2.0 1.20 22% 14.6 9.6 6.2 4.0 2.
BETRIEBSMODI Stereobetrieb Für den Stereobetrieb (mit zwei Kanälen) schalten Sie den Verstärker aus und stellen die Moduswahlschalter auf der Rückseite auf die ausgerastete (herausgezogene) Position. In diesem Modus arbeiten beide Kanäle unabhängig voneinander, wobei ihre jeweiligen Pegel über die Eingangsdämpfer geregelt werden.
703%&34&*5& 703%&34&*5& 703%&34&*5& 3f$,4&*5& 3f$,4&*5& 3f$,4&*5& 4$)"-5&3 6/% 3&(-&3 4$)"-5&3 6/% 3&(-&3 4$)"-5&3 6/% 3&(-&3 8FDITFMTUSPN /FU[TDIBMUFS -FJTUVOHTTDIBMUFS 8FDITFMTUSPN /FU[TDIBMUFS -FJTUVOHTTDIBMUFS %JF 7FSTUjSLFS EFS $4 %JF 7FSTUjSLFS EFS $4 4FSJFT TJOE NJU FJOFN LPNCJOJFSUFO 8FDITFMTUSPN /FU[TDIBMUFS C[X -FJTUVOHTTDIBMUFS BVG EFS 4FSJFT TJOE NJU FJOFN LPNCJOJFSUFO 8FDITFMTUSPN /FU[TDIBMUFS C[X -FJTUVOHTTDIBMUFS BVG EFS 8FDITFMTUSPN /FU[T
VORDERSEITE 3 1 2 3 1 2 ANZEIGEN Die Verstärker der CS® Series sind mit drei LED-Anzeigen pro Kanal auf der Vorderseite ausgestattet: PWR (Power), SIG (Signal) und DDT™ (Distortion Detection Technique). Die LED-Anzeigen informieren den Anwender über den Betriebsstatus des jeweiligen Kanals und warnen vor möglichen Störungen. PWR-LED (1) Die Power-LED zeigt an, dass das Gerät in Betrieb ist. Sie leuchtet beim Normalbetrieb sowie auch bei aktivierter DDTSchaltung des Kanals auf.
SCHUTZFUNKTIONEN Die Peavey CS® Series ist mit verschiedenen Schaltungen ausgestattet, durch die Verstärker und Lautsprecher in nahezu jeder Situation geschützt werden. Peavey hat die Verstärker so narrensicher wie möglich und dazu unempfindlich gegenüber Kurzschluss, Leerlauf, ungeeigneten Lasten, Gleichspannung und Überhitzung gemacht. Schaltet ein Kanal in den DDT™Modus zur Gain-Verringerung, leuchtet die DDT-LED auf. Clipping-Prozentsatz oder Ausgangsleistung werden jedoch sofort verringert.
SCHUTZFUNKTIONEN RampUp™-Signalregelung Wird ein Verstärker der CS® Series eingeschaltet oder ein Schutzmodus ausgeschaltet, wird die RampUp-Schaltung aktiviert. Solange die Lautsprecher abgetrennt sind, dämpft die RampUp-Schaltung das Signal vollständig und aktiviert die DDT™-LED. Nachdem sich das Ausgangsrelais geschlossen hat, steigt das Signal langsam und allmählich auf seinen eingestellten Pegel an. Die PWR-LED leuchtet auf und die DDT-LED erlischt, wenn das Signal nicht mehr gedämpft wird.
WARTUNG DES VERSTÄRKERS UND VERANTWORTUNG DES NUTZERS Eine regelmäßige Wartung der Verstärker der CS Series ist nicht erforderlich, und eine interne Justierung sollte während ihrer gesamten Lebensdauer überflüssig sein. Ihr Verstärker der CS Series ist äußerst leistungsfähig und kann sowohl für Lautsprecher als auch für Personen Gefahren bergen.
CS ® Series 3000/4000/4080 HZ Endstufen TECHNISCHE DATEN CS 3000 CS 4000 CS 4080 HZ Nennleistung 4 Ohm gebrückt 3.050 Watt bei 1 kHz bei <0,1% Klirrfaktor 4.000 Watt bei 1 kHz bei <0,1% Klirrfaktor 4.080 Watt bei 1 kHz bei <0,1% Klirrfaktor Nennleistung 2 x 2 Ohm 1.500 Watt pro Kanal bei 1 kHz bei <0,05% Klirrfaktor, beide Kanäle getrieben 2.000 Watt pro Kanal bei 1 kHz bei <0,1% Klirrfaktor, beide Kanäle getrieben - Nennleistung 2 x 4 Ohm 1.
CS® Series TECHNISCHE DATEN CS 3000 CS 4000 >15V/us CS 4080 HZ Anstiegsgeschwindigkeit >15V/us Dämpfungsfaktor (8 Ohm) >500:1 bei 20 Hz -1 kHz >500:1 bei 20 Hz -1 kHz >500:1 bei 20 Hz -1 kHz Phasenfrequenzgang +5 bis -15 Grad von 20 Hz-20 kHz +5 bis -12 Grad von 20 Hz-20 kHz +5 bis -12 Grad von 20 Hz-20 kHz Eingangsempfindlichkeit 1,6 Volt +/- 3% für 1 kHz. 4 Ohm Nennleistung, 1,37 Volt +/- 3% für 1 kHz. 2 Ohm Nennleistung 1,84 Volt +/- 3% für 1 kHz.
FRANÇAIS CS® 3000/4000/4080 HZ Amplificateurs de Puissance Félicitations d’avoir choisi un amplificateur de puissance Peavey de la série CS. Ces unités sont concues pour vous permettre une utilisation intensive sans problèmes de fiabilité ou d’utilisation. Le tout dans une unité compacte, ils proposent une circuiterie de pointe et des systèmes de protection qui ont fait la renommée de Peavey.
*OUSPEVDUJPO *OUSPEVDUJPO 1SnDBVUJPOT Eµ6UJMJTBUJPO 1SnDBVUJPOT Eµ6UJMJTBUJPO *OUSPEVDUJPO "TTVSF[ WPVT RVF MµBMJNFOUBUJPO nMFDUSJRVF FTU DPSSFDUF QPVS WPUSF VOJUn VOF nUJRVFUUF QSnDJTF MFT WPMUBHFT FU "TTVSF[ WPVT RVF MµBMJNFOUBUJPO nMFDUSJRVF FTU DPSSFDUF QPVS WPUSF VOJUn VOF nUJRVFUUF QSnDJTF MFT WPMUBHFT FU DPOTPNNBUJPO EF WPUSF VOJUn TJUVnF TVS TB GBDF BSSJoSF "VDVOF HBSBOUJF OF DPVWSF MFT EPNNBHFT DSnnT h VOF DPOTPNNBUJPO EF WPUSF VOJUn TJUVnF TVS TB GBDF BSSJoSF "VDVOF HBSBOUJF OF DPVWSF M
La Charte De Dimensions Des Cables Stranded Cable Lgth. (ft.) Wire Gauge (AWG) Power Loss (8 ohm load) Power Loss (4 ohm load) Power Loss (2 ohm load) 5 18 16 14 12 10 0.81% 0.51 0.32 0.20 0.128 1.61% 1.02 0.64 0.40 0.25 3.2% 2.0 1.28 0.80 0.51 10 18 16 14 12 10 1.61% 1.02 0.64 0.40 0.25 3.2% 2.0 1.28 0.80 0.51 6.2% 4.0 2.5 1.60 1.01 40 18 16 14 12 10 8 6.2% 4.0 2.5 1.60 1.01 0.60 11.9% 7.7 5.0 3.2 2.0 1.20 22% 14.6 9.6 6.2 4.0 2.4 18 16 14 12 10 8 11.9% 7.7 5.0 3.2 2.0 1.20 22% 14.
Modes d’Opération Stéréo Pour le mode Stéréo (double canal), mettre votre unité hors-tension et positionnez le sélecteur de mode en position Stéréo. Dans ce mode, les contrôles de gain affectent leurs canaux respectifs. Le signal à l’entrée 1 sera récupéré amplifié à la sortie 1, et de même pour le canal 2. Pont Deux canaux de votre unité peuvent être combinés comme un seul amplificateur mono de forte puissance (canaux 1 et 2 ).
1BOOFBV "WBOU 1BOOFBV "WBOU 1BOOFBV "WBOU 1BOOFBV "WBOU 1BOOFBV "SSJoSF 1BOOFBV "SSJoSF 1BOOFBV "SSJoSF 1BOOFBV "SSJoSF 4nMFDUFVST $POUSyMFT 4nMFDUFVST $POUSyMFT 4nMFDUFVST $POUSyMFT "$ 1PXFS 4XJUDI $JSDVJU #SFBLFS 4nMFDUFVST $POUSyMFT "$ 1PXFS 4XJUDI $JSDVJU #SFBLFS "$ 1PXFS 4XJUDI $JSDVJU #SFBLFS *M Z B EFVY EJTKPODUFVST EBOT DIBRVF VOJUn *MT QFSNFUUFOU EF MJNJUFS MµBMJNFOUBUJPO nMFDUSJRVF FU nWJUFS UPVUF TVSDIBVGGF *M Z B EFVY EJTKPODU
Panneau Avant 3 1 2 3 1 2 Indicateurs Les unités de la série CS® sont munies de trois Leds d’indication par canal: PWR (power), SIG (signal), et DDT™ (Distortion Detection Technique). Ces Leds vous informent de l’état de fonctionnement du canal et vous previennent d’éventuels problèmes. PWR LED (1) Cette Led vous indique que le canal est en état de fonctionnement.
Systèmes de Protection Les unités de la série CS® incorporent de nombreux systèmes de protection pour tout problème à eux-même ou aux enceintes. Peavey a essayé de rendre l’appareil fiable, quelque soient les manipulations effectuées. Circuits de sortie ouvert, courant continu, mauvaise charge d’enceintes, surchauffe,… sont toutes des conditions pour lesquelles votre unité est équipée en protection.
Systèmes de Protection Système RampUp™ (contrôle de montée en puissance) Dès que votre unité est mise sous tension ou après qu’une protection se désengage, le circuit RampUp™ est activé. Le gain du signal est graduellemnt augmenté jusqu’à la valeur du contrôle du canal correspondant.
Maintenance et Responsabilité d’Utilisateur Les unités CS ne demande pas de maintenance particulière et ne devrait jamais nécessiter de réglages internes tout au long de sa durée de vie. Il est de votre responsabilité de lire attentivement les messages de précaution et d’utiliser correctement votre unité. Votre amplificateur est de forte puissance et travaille avec des tensions qui peuvent être fatales à l’homme. De plus, de nombreuses enceintes peuvent être gravement endommagées par une surpuissance.
CS ® Series 3000/4000/4080 HZ Amplificateurs de Puissance SPECIFICATIONS CS 3000 CS 4000 CS 4080 HZ Puissance mesurée 4 ohms (pont) Puissance mesurée 2 x 2 ohms 3,050 watts @ 1 kHz à <0.1% T.H.D. 4,000 watts @ 1 kHz à <0.1% T.H.D. 4,080 watts @ 1 kHz à <0.1% T.H.D. 1,500 watts par canal @ 1 kHz <0.05% T.H.D. en utilisation des 2 canaux 2,000 watts par canal @ 1 kHz <0.1% T.H.D. en utilisation des 2 canaux N/A Puissance mesurée 2 x 4 ohms 1,025 watts par canal @ 1 kHz à <0.05% T.H.D.
CS® Series SPECIFICATIONS CS 3000 CS 4000 CS 4080 HZ Facteur d’amortissement (8 ohms) Phase Response > 500:1 @ 20 Hz - 1 kHz > 500:1 @ 20 Hz - 1 kHz > 500:1 @ 20 Hz - 1 kHz +5 to - 15 degrees from 20 Hz to 20kHz +5 to - 12 degrees from 20 Hz to 20kHz +5 to - 12 degrees from 20 Hz to 20kHz Sensibilité d’entrée 1.6V +/-3% pour 1kHz.@4 ohms 1.37 V +/-3% pour 1 kHz.@2ohms 1.84V +/-3% pour 1kHz.@4 ohms 1.58 V +/-3% pour 1 kHz.@2ohms 2.25V +/-3% pour 1kHz.
ESPAÑOL CS® 3000/4000/4080 HZ Etapas de Potencia Felicidades por su adquisición de una etapa de Potencia de la Serie CS de Peavey! Diseñada para operar con seguridad durante años, la Serie CS de amplificadores ofrece superioridad de sonido y una fiabilidad insuperable por las que Peavey es famosa, en una unidad compacta y robusta. La tecnología avanzada y la protección de circuito extensiva permiten una operación muy eficiente, incluso bajo cargas y condiciones de potencia difíciles.
*/530%6$$*Î/ */530%6$$*Î/ 1SFDBVDJPOFT EF 0QFSBDJwO 1SFDBVDJPOFT EF 0QFSBDJwO */530%6$$*Î/ )BZ RVF BTFHVSBSTF EF RVF FM WPMUBKF VUJMJ[BEP FT FM NJTNP JNQSFTP FO MB QBSUF USBTFSB EFM BNQMJGJDBEPS -PT EBvPT )BZ RVF BTFHVSBSTF EF RVF FM WPMUBKF VUJMJ[BEP FT FM NJTNP JNQSFTP FO MB QBSUF USBTFSB EFM BNQMJGJDBEPS -PT EBvPT RVF SFTVMUFO EFM VTP EF WPMUBKF FRVJWPDBEP OP FTUgO DVCJFSUPT QPS OJOHVOB HBSBOUrB EF MB 4FSJF $4 7FB MB TFDDJwO EF 7FB MB TFDDJwO EF RVF SFTVMUFO EFM VTP EF WPMUBKF FRVJWPDBEP OP FT
Tablas de Calibre del Cable Stranded Cable Lgth. (ft.) Wire Gauge (AWG) Power Loss (8 ohm load) Power Loss (4 ohm load) Power Loss (2 ohm load) 5 18 16 14 12 10 0.81% 0.51 0.32 0.20 0.128 1.61% 1.02 0.64 0.40 0.25 3.2% 2.0 1.28 0.80 0.51 10 18 16 14 12 10 1.61% 1.02 0.64 0.40 0.25 3.2% 2.0 1.28 0.80 0.51 6.2% 4.0 2.5 1.60 1.01 40 18 16 14 12 10 8 6.2% 4.0 2.5 1.60 1.01 0.60 11.9% 7.7 5.0 3.2 2.0 1.20 22% 14.6 9.6 6.2 4.0 2.4 18 16 14 12 10 8 11.9% 7.7 5.0 3.2 2.0 1.20 22% 14.6 9.6 6.
MODOS DE OPERACIÓN Operación Estéreo Para la operación en estéreo (doble canal), apague el amplificador y coloque los interruptores de selección de modo del panel trasero en la posición estéreo. En este modo, ambos canales operan independientemente el uno del otro, con sus atenuadores de entrada controlando sus respectivos niveles.
1"/&- '30/5"1"/&- '30/5"1"/&- '30/5"- 1"/&- 53"4&30 1"/&- 53"4&30 1"/&- 53"4&30 */5&3361503&4 : $0/530-&4 */5&3361503&4 : $0/530-&4 *OUFSSVQUPS EF &ODFOEJEP "$ $JSDVJUP #SFBLFS *OUFSSVQUPS EF &ODFOEJEP "$ $JSDVJUP #SFBLFS */5&3361503&4 : $0/530-&4 -B 4FSJF $4 -B 4FSJF $4 EF BNQMJGJDBEPSFT QPTFFO VOB DPNCJOBDJwO EF JOUFSSVQUPS "$ CSFBLFS EF DJSDVJUP FO FM QBOFM GSPOUBM 4J FM EF BNQMJGJDBEPSFT QPTFFO VOB DPNCJOBDJwO EF JOUFSSVQUPS "$ CSFBLFS EF DJSDVJUP FO F
PANEL FRONTAL 3 1 2 3 1 2 INDICADORES Los amplificadores de la Serie CS® poseen tres indicadores LED por canal en el canal frontal: PWR (encendido), SIG (señal) y DDT™ (Técnica de Detección de Distorsión). Estos indicadores LED informan al usuario del status de operación de cada canal y avisan sobre posibles condiciones anormales. LED PWR (1) El LED power indica que el canal está operativo.
CARACTERÍSTICAS DE PROTECCIÓN La Serie CS® de Peavey incorpora numerosos circuitos que protegen tanto al amplificador como a los altavoces bajo virtualmente cualquier situación. Peavey ha fabricado este amplificador lo más infalible posible haciéndolo inmune a los corto-circuitos y a los circuitos abiertos, cargas descompensadas, voltaje DC y sobrecalentamiento. Si un canal se pone en el modo de reducción de ganancia DDT™, el LED DDT se iluminará.
CARACTERÍSTICAS DE PROTECCIÓN Control de Señal RampUp™ En cuanto un amplificador CS® se enciende o sale del modo protect, el circuito RampUp se activa. Mientras los altavoces estén desconectados, el circuito RampUp atenúa totalmente la señal y activa el LED DDT. Tras el cierre del relé de salida , la señal aumenta lenta y gradualmente hasta su nivel establecido. El LED PWR se iluminará y el LED DDT se apagará cuando la señal haya dejado de ser atenuada.
MANTENIMIENTO DEL AMPLIFICADOR Y RESPONSABILIDAD DEL USUARIO Un amplificador de la Serie CS® no requiere mantenimiento regular y no debe requerir ningún ajuste interno durante su vida. Su amplificador es muy potente y puede ser potencialmente peligroso para los altavoces y humanos por igual. Es su responsabilidad leer la Sección de Precauciones Importantes y asegurarse que el amplificador es instalado, cableado y operado apropiadamente y de acuerdo con este manual.
CS ® Series 3000/4000/4080 HZ Etapas de Potencia ESPECIFICACIONES CS 3000 Potencia tasada bridged CS 4000 CS 4080 HZ 3,050 vatios a 1 kHz a 4,000 vatios a 1 kHz a 4,080 vatios a 1 kHz a <0.1% T.H.D. @ 4 ohmios <0.1% T.H.D. @ 4 ohmios <0.1% T.H.D. @ 8 ohmios 1,500 vatios por canal a 1 2,000 vatios por canal a 1 ambos canales ambos canales 1,025 vatios por canal a 1,350 vatios por canal a 1 kHz a <0.05% T.H.D. usando ambos canales 2,040 vatios por canal a 1 kHz a <0.05% T.H.D.
ESPECIFICACIONES CS 3000 CS 4000 CS 4080 HZ Tasa Slew > 15V/us > 15V/us > 15V/us Factor Damping (8 ohmios) > 500:1 a 20 Hz - 1 kHz > 500:1 a 20 Hz - 1 kHz > 500:1 a 20 Hz - 1 kHz Respuesta de Fase De +5 a - 15 grados desde De +5 a - 15 grados desde De +5 a - 15 grados desde 20 Hz a 20kHz 20 Hz a 20kHz 20 Hz a 20kHz Sensibilidad de Entrada 1.6 voltios +/- 3% para 1 kHz. Potencia tasada a 4 ohmios, 1.37 voltios +/- 3% para 1 kHz. Potencia tasada a 2 ohmios 1.84 voltios +/- 3% para 1 kHz.
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: 09/15/2010 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.
U.S. CUSTOMER WARRANTY REGISTRATION Optional Product Extended Warranty Registration Give us some information and put your extended warranty into effect! Please take a few minutes to fill out this information/survey sheet to help us get to know and serve you better. To save time, submit your warranty registration online at www.peavey.com/support/warrantyregistration 1. 7.
FROM: Place Postage Here Peavey Electronics Corporation Attn: Warranty Department P.O.