Operation Manual

37
IPR2
™
5000 DSP Specification Sheet
Rated Watts 2ch x 2 ohms 3230 watts 20ms repetitive burst / 2530 watts 1% THD both channels driven @ 1kHz.
Rated Watts 2ch x 4 ohms 1985 watts 20ms repetitive burst / 1700 watts 1% THD / 1470 watts 0.15% THD, both channels driven @ 1kHz.
Rated Watts 2ch x 8 ohms 1175 watts 20ms repetitive burst / 1025 watts 1% THD / 880 watts 0.15% THD, both channels driven @ 1kHz.
Minimum Load Impedance 2 ohms
Maximum RMS Voltage Swing 105 volts
Frequency Response 20Hz - 22kHz; +/- 0.5dB at 1 watt.
20Hz - 20kHz 2ch x 2 ohms <0.5% @ 2250 watts 20Hz to 4kHz, decreasing to 1640 watts @ 20kHz, both channels driven.
20Hz - 20kHz 2ch x 4 ohms <0.15% @ 1400 watts 20Hz to 10kHz, decreasing to 1350 watts @ 20kHz, both channels driven.
20Hz - 20kHz 2ch x 8 ohms <0.15% @ 860 watts 20Hz to 4kHz, increasing to 1000 watts @ 20kHz, both channels driven.
Input CMRR > - 75dB @ 1 kHz.
Voltage Gain x 70 (+37dB)
Crossover Adjustable High Pass and Low Pass lter per channel. Filter Types: 12dB/oct 2nd order, 18dB/oct 3rd
order, 24dB/oct 4th order Butterworth and 24dB/oct 4th order Linkwitz –Riley.
Crosstalk -60dB @ 1kHz @ 700 watts power @ 8 ohms.
Hum and Noise > -96dB, “A” weighted referenced to rated power @ 4 ohms.
Slew Rate > 12V/μs
Damping Factor (8 ohms) > 210:1 @ 20Hz - 1kHz @ 8 ohms
Input Sensitivity 1.094 volts +/- 3% for 1 kHz 4 ohm rated power, 1.025 volts +/- 3% for 1 kHz 2 ohm rated power.
Input Impedance 12 kilohms, balanced and 6 kilohms unbalanced.
Current Draw @ 1/8 in VA (watts) 1435 (890) @ 2 ohms, 920 (525) @ 4 ohms, 625 (335) @ 8 ohms
Current Draw @ 1/3 in VA (watts) 3050 (2155) @ 2 ohms, 1880 (1200) @ 4 ohms, 1200 (715) @ 8 ohms
Idle Consumption 195VA, 90 watts.
Cooling 3 temperature dependent variable speed fans.
Controls 2 front panel attenuators, crossover select switch for HPF, Normal and LPF
Indicator LEDs Five LED indicators per channel: Active, Signal, DDT, Temperature and DC
Protection Thermal, DC, subsonic, incorrect loads, under and over voltage
Connectors Inputs: Dual combination 1/4” XLR, Outputs: Dual male XLR input thru, one 2-pin & one 4 pin twist-lock connector
Construction 0.062” thick aluminum
Dimensions 3.5”x19”x 17” behind front panel + 0.6” for handle
Net Weight 6.2 kg (13.6 lbs.*)
Gross Weight 7.9 kg (17.4 lbs.)
Rated power readings made with BW: 20 Hz to 22 kHz. All power measurements made @ 120 VAC or 240VAC.
2 ohm steady state sine wave power is time limited by circuit breaker.
Bridge operation is not possible.
*Net Weight does not include power cord.