DS-LEDA27 Series For Absen Acclaim ENG *Actual configuration may vary 1 2018-05-15 #:146-9026-4 (2019-08-15)
WARNING ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation. Before installing make sure the supporting surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
ENG Parts (Before beginning, make sure you have all parts shown below). Parts List A1 A2 B1 B2 B3 C D E F G H I J K Description outside vertical column kit left column right column spacer kit top vertical spacer bottom vertical spacer (not used) horizontal spacer inside vertical column kit top horizontal extrusion asy bottom horizontal extrusion asy extrusion connector 3mm allen wrench 2-tip t-handle M5 x 5mm set screw #14 x 2.
1 ENG Refer to layout drawing included for your specific model.
2-1 G ENG Optional: If connecting two top horizontal extrusions, first remove inner hook-on brackets. D D ENG Remove and save hardware. 2-2 G ENG Use extrusion connectors to connect top horizontal extrusions.
2-3 G ENG Replace one hook-on bracket in between connected extrusions. D D ENG Use saved hardware. 3-1 G ENG Optional: If connecting two bottom horizontal extrusions, first remove inner hook-on brackets E E ENG Remove and save hardware.
3-2 G ENG Use extrusion connectors to connect bottom horizontal extrusions. F (3) E H (6) E 3-3 G ENG Replace one hook-on bracket in between connected extrusions. E E ENG Use saved hardware.
4 WARNING ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood may be covered by gypsum board (drywall) up to 5/8" thick. 4-1 ENG Use a laser level to keep mounting holes level.
4-2 ENG Level top horizontal extrusion and mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick.) 3.
4-3 2.5" (64mm) 5/32" (4mm) 5/32" (4mm) ENG Drill mounting holes into supporting surface (2.5" (64mm) minimum depth required). 4-4 ENG Level extrusion. Install using wood screws provided. 3/8" (10mm) I (7) D ENG Maximum 80 in. • lb (9 N.M.).
4-5 ENG Edges must be flush. ENG Secure vertical spacers to the wall flush with the horizontal extrusion.
4-6 ENG Use third vertical spacer to align bottom horizontal extrusion flush with vertical spacer, then mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick.) 56.19" (143cm) B1 ENG Edges must be flush.
4-7 2.5" (64mm) 5/32" (4mm) 5/32" (4mm) ENG Drill mounting holes into supporting surface (2.5" (64mm) minimum depth required). 4-8 ENG Use third vertical spacer to align bottom horizontal extrusion flush with vertical spacer, then install using wood screws provided. 3/8" (10mm) I (7) E ENG Maximum 80 in. • lb (9 N.M.).
4-9 ENG Remove vertical spacer.
5-1 G ENG Hook on and secure outer vertical columns. "L" and "R" markings designate left and right ENG Tighten hardware. column.
5-2 ENG Hook on and secure all inside vertical columns. G ENG Tighten hardware.
6-1 G ENG Loosen hardware on vertical columns.
6-2 G ENG Plumb and level outer columns, then tighten hardware. Tighten hardware on four corner wall plates. ENG Tighten. ENG Tighten.
6-3 G ENG Tie a string between top slots on outer columns in order to level the depth of each vertical column. ENG Loosen, adjust, tighten. ENG Optional leveling for bowed walls ENG Loosen. ENG Insert. K ENG Tighten.
6-4 G ENG Tie a string between bottom slots on outer columns in order to level the depth of each vertical column. ENG Loosen, adjust, tighten. ENG Optional leveling for bowed walls ENG Loosen. ENG Insert. K ENG Tighten.
6-5 ENG Tighten or loosen to adjust height.
6-6 G ENG Adjust inner columns to fit horizontal spacers. Tighen column hardware after spacing. Start from the left column.
6-7 G ENG Continue adjusting inner columns to fit horizontal spacers until all are level.
6-8 ENG Remove all spacers.
7-1 G ENG Optional: For shallow depth installations, flip wall bracket orientation as shown. 2.25" (57mm) MIN 3.05" (77mm) MAX wall display tile wall display tile 2.60" (66mm) MIN 2.
7-2 ENG Level L brackets and mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick.
7-3 2.5" (64mm) 5/32" (4mm) 5/32" (4mm) ENG Drill mounting holes into supporting surface (2.5" (64mm) minimum depth required). 7-4 ENG Level L brackets. Install using wood screws provided. 3/8" (10mm) ENG Maximum 80 in. • lb (9 N.M.).
7-5 G ENG Tie a string between center slots on outer column in order to level the depth of each vertical column.
7-6 G ENG Adjust depth, then remove string. ENG Loosen, adjust, tighten.
8-1 3/8" (10mm) ENG Attach display, tighten connecting hardware, and run cables one at a time starting from the bottom left.
8-2 3/8" (10mm) 21 16 22 11 17 23 12 18 7 13 6 24 25 14 8 9 15 10 31 2018-05-15 #:146-9026-4 (2019-08-15)
9 3/8" (10mm) ENG To remove, start from the top right.
ENG This page intentionally left blank.
ENG This page intentionally left blank.
LIMITED FIVE-YEAR WARRANTY Peerless Industries, Inc. (“Peerless-AV”) warrants to original end-users that each Peerless-AV® mounting product will be free from defects in material and workmanship, under normal use, for the applicable warranty period (from date of the original installation of the product). At its option, Peerless-AV will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
Peerless-AV 2300 White Oak Circle Aurora, IL 60502 Email: tech@peerlessmounts.com Ph: (800) 865-2112 Fax: (800) 359-6500 www.peerless-av.com Peerless-AV Europe Unit 3 Watford Interchange, Colonial Way, Watford, Herts, WD24 4WP, United Kingdom Customer Care 44 (0) 1923 200 100 www.peerless-av.com Peerless-AV de Mexico Ave de las Industrias 413 Parque Industrial Escobedo Escobedo N.L Mexico 66062 Servicio al Cliente 01-800-849-65-77 www.peerless-av.com © 2019, Peerless Industries, Inc.