Installation Manual

ManualsBrandsPeerless-AV ManualsAudio Visual PresentationIn Wall Mount for 32 to 60" Flat Screen

Installation and Assembly:

In-wall Mount for 32" to 71" Flat Panel Displays

Maximum UL Load Capacity: 200 lb (91 kg)

IM760P

IM760P-S

IM760PU

IM760PU-S

This product is intended for use with UL

Listed products and must be installed by a

qualiﬁ ed professional installer.

Model# Display size range

IM760P, IM760P-S 32" to 71" (81 to 180 cm)

IM760PU, IM760PU-S 32" to 65" (81 to 165 cm)

ISSUED: 12-04-07 SHEET #: 095-9279-9 (2014-03-17)

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com

Summary of content (12 pages)

PAGE 1
Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays Model# Display size range IM760P, IM760P-S 32" to 71" (81 to 180 cm) IM760PU, IM760PU-S 32" to 65" (81 to 165 cm) This product is intended for use with UL Listed products and must be installed by a qualified professional installer. Maximum UL Load Capacity: 200 lb (91 kg) IM760P IM760P-S IM760PU IM760PU-S 2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.
PAGE 2
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112.
PAGE 3
Before you begin, make sure all parts shown are included with your product. Parts List A B C D E F G H J K L M N O P Q R T V W X Y Z Description arm assembly in-wall box arm axle outer trim #14 x 2.
PAGE 4
Part List Continued Parts may appear slightly different than illustrated.
PAGE 5
Installation to Wood Stud Wall 1 In-wall box (B) can be installed between two 2" x 4"studs 16" off center. Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended. Based on its edges, draw vertical lines down the inside edges of stud’s. Mark desired center of display between studs. Draw a horizontal line above desired center of display as indicated in figure 1.1 or 1.2.
PAGE 6
Installation to Wood Stud Wall (continued) WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud.
PAGE 7
Installing Arm to In-wall Box 2 Insert arm axle (C) through arm assembly (A) as shown in figure 2.1. C Position arm axle (C) and arm assembly (A) into axle support bracket of in-wall box (B) then seat arm axle through bottom hole of in-wall box as shown in figure 2.2. A Secure arm axle to in-wall box using four M5 x 12mm phillips screws (L) as shown in figure 2.3. fig. 2.1 C B AXLE SUPPORT BRACKET L C A fig. 2.2 fig. 2.
PAGE 8
Attaching Adapter Plate to Display with VESA® Mounting Pattern 4 NOTE: For installing display using universal adapter plate, skip to step 5. Identify VESA mounting pattern on back of your display and choose hole pattern on adapter plate and required fasteners as shown in figure 4.2. Secure adapter plate to back of display as shown in figure 4.1 using fasteners indicated in figure 4.2.
PAGE 9
Installing Universal Adapter Plate to Display Using the hole pattern shown in detail 1, attach the adapter plate to universal adapter plate (T) with four M10 x 17mm screws (X) as shown. Tighten screws using 6mm allen wrench (Y). 5 LARGE HOLES HOLE PATTERN FOR USE WITH UNIVERSAL ADAPTER PLATE T ADAPTER PLATE X DETAIL 1 WARNING • Tighten screws so display brackets are firmly attached to display. Do not tighten with excessive force.
PAGE 10
For Flat Back Display 6-2 Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into display as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
PAGE 11
Adjustment of Flat Panel Display 7 Adjustment of Flat Panel Display TILT Adjustment: Adjust tension knob on side of mount to desired tension to enable tilt adjustment and balance your display size and weight as shown in figure 7.1. Push or pull from top or bottom of display to adjust tilt as shown. The tilt can be adjusted to a maximum of 10° forward or 5° backward. Retighten tension knob. 8 ROLL Adjustment: Loosen M5 x 25mm screws using 4mm allen wrench (K).
PAGE 12
Cable Management 9 For optional installation of UL listed single receptacle electrical box, access plates located on the bottom or top of in-wall box can be temporarily removed to install electrical box as shown in figure 9.1. ACCESS PLATE fig. 9.1 9-1 DISPLAY NOT SHOWN FOR CLARITY Insert up to eight cable management clips (J) into the desired positions in the arm assembly and in-wall box as shown in figure 9.2 for routing cables.