IRTO49-200, IRTO55-200 ENG 1 2018-11-28 #:180-9122-1
WARNING ENG - Before installing make sure the supporting surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. Be careful not to pinch fingers when operating the mount. For support please call customer care at 1-800-865-2112.
ENG Parts (Before beginning, make sure you have all parts shown below). ESP Piezas (antes de iniciar, asegúrese de tener todas las piezas siguientes). FRN Pièces (avant de commencer, assurez-vous d’avoir toutes les pièces illustrées ci-dessous).
1-1 ENG Drainage holes indicate bottom of overlay. R 552 HB ly X , te 92 B4 ara XH ld sep so A ENG Drainage holes indicate bottom of overlay.
1-2 ENG Center display by adjusting knobs.
2 F E C (8) A B (4) 3 ENG Tighten. ESP Apretar. FRN Serrer.
ENG This page intentionally left blank. ESP Página en blanco. FRN Cette page a été laissée en blanc intentionnellement.
4 ENG Connect source device, and waterproof USB extensions with electrical tape or heat-shrinking tube. A 5-1 ENG Optional: If use of IR sensor is required, insert the 3.5mm end of the IR Extender into the IR Extender port on the input panel of the display (sold seperately). Connecting the IR Extender will disable the factory installed IR sensor.
5-2 G 5-3 ENG If use of IR sensor is required, install IR extender in a location within line of sight of remote signal. ER POW TV VCR MUTE DVD 1 4 CE 2 SAT SOUR CBL 7 .
6-1 ENG Optional: If use of ALS sensor is required, insert the 3.5mm end of the ALS Extender (ACCD-ALS sold separately) into the ALS Extender port on the input panel of the display (sold seperately). Connecting the ALS Extender will disable the factory installed ALS sensor. ALS Extender ENG Sold separately.
6-2 ENG Sold separately. 6-3 ENG If use of ambient light sensor is required, install ALS extender in a location representative of actual ambient light.
7a ENG Windows Calibration Instructions For most operating systems and display orientations calibration is not required. If the touch points are not being registered accurately please follow the instructions below for calibrating your IR Touch Overlay. You will need to connect a mouse until your IR Touch Overlay is calibrated properly. 1. Please go to the following website https://www.imanageshare.com/pd/3p8nBT6IerQ and download the calibration software for the operating system that you are using. 2.
7b ENG Mac Calibration Instructions For most operating systems and display orientations calibration is not required. If the touch points are not being registered accurately please follow the instructions below for calibrating your IR Touch Overlay. You will need to connect a mouse until your IR Touch Overlay is calibrated properly. 1. Please go to the following website https://www.imanageshare.com/pd/AicFN9Jx2hM and download the calibration software for the operating system that you are using. 2.
LIMITED TWO-YEAR WARRANTY TWO-YEAR PARTS & LABOR LIMITED WARRANTY • Any unit tampered with, modified, adjusted or repaired by any party other than the Peerless-AV Authorized Service Provider. • Any cosmetic damages to the surface or exterior that has been defaced or faded, or caused by normal wear and tear or exposure to chemicals, acid rain, large hail or adverse weather conditions. • Return shipping when no defect is found.
2018-11-28 #:180-9122-1
Peerless-AV 2300 White Oak Circle Aurora, IL 60502 Email: tech@peerlessmounts.com Ph: (800) 865-2112 Fax: (800) 359-6500 www.peerless-av.com Peerless-AV Europe Unit 3 Watford Interchange, Colonial Way, Watford, Herts, WD24 4WP, United Kingdom Customer Care 44 (0) 1923 200 100 www.peerless-av.com Peerless-AV de Mexico Ave de las Industrias 413 Parque Industrial Escobedo Escobedo N.L Mexico 66050 Servicio al Cliente 01-800-849-65-77 www.peerless-av.com © 2018, Peerless Industries, Inc.