Installation Manual

ManualsBrandsPeerless-AV ManualsAccessoriesFlat Panel Ceiling Mount with Cord Management Covers

Features:

• Comes in two adjustable height ranges (in 1"

increments): 18"-30" and 36"-48"

• -5° to +20° adjustable tilt

• Screen can be mounted in standard position or

face-down

• Portrait or landscape orientation

• Ceiling plate included

• Hardware included for wood or concrete installa-

tions

• Snap-together cover provides sleek aesthetics and

cord management

• Theft resistant security fasteners included

• VESA

75/100 mm compliant (Non-VESA adapter

offered separately)

• Comes in black and silver

• 360° swivel action

Vertical

Position

Horizontal

Position

Models: LCC18-C, LCC18-CS, LCC36-C, LCC36-CS

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerless-av.com

ISSUED: 09-27-04 SHEET #: 100-9005-8 12-13-12

Installation and Assembly:

Ceiling mount for LCD screens up to 29"

Max UL Load Capacity: 40 lb (18.1 kg)

Summary of content (14 pages)

PAGE 1
Installation and Assembly: Ceiling mount for LCD screens up to 29" Models: LCC18-C, LCC18-CS, LCC36-C, LCC36-CS Features: • Comes in two adjustable height ranges (in 1" increments): 18"-30" and 36"-48" • -5° to +20° adjustable tilt • Screen can be mounted in standard position or face-down • Portrait or landscape orientation • Ceiling plate included • Hardware included for wood or concrete installations • Snap-together cover provides sleek aesthetics and cord management Horizontal Position Vertical Positi
PAGE 2
Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-729-0307. • This product should only be installed by a qualified professional.
PAGE 3
Parts List A B C D E F G H I J K L M N O P Q R S T U V W Description tube assembly ceiling plate tilt bracket reducer #14 x 2.
PAGE 4
Installation to Wood Joist Finished Ceilings, Exposed Wood Joists, or Wood Beam Ceilings WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.).
PAGE 5
Installation to Concrete Ceilings WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90 specifications.
PAGE 6
Installing Reducer Thread reducer (D) onto tube assembly (A) until tight. Insert set screw (I) into reducer as shown in figure 2-1. Tighten screw using hex wrench (J). Note: Set screw (I) is used to jam against the threads of tube assembly to prevent any excess movement. To adjust height of tube assembly (A), remove socket pin screw and two lock washers using 4 mm security allen wrench (G) and adjust to desired height as shown in figure 2-2.
PAGE 7
Flush Mount Installation Screw reducer (D) into ceiling plate (B) until notch in reducer is aligned with one of the four holes in ceiling plate and set screw (I) is at least partially covered by ceiling plate as shown in figure 3-1. Secure reducer with one M5 x 10 mm F-type socket pin screw (P) using security allen wrench (G) as shown in figure 3-2. Note: Slotted set screw (N) is used to jam against the threads of the reducer to prevent any excess movement of the tube assembly (A).
PAGE 8
Installation to Extension Column Screw extension column (EXT or ADJ Series) to ceiling plate (B). Align the notch with one of the four holes in the ceiling plate and secure extension column with a M5 x 10 mm socket pin screw (P) using security allen wrench (G). See figure 3-5. Note: Slotted set screw (N) is used to jam against the threads of the reducer to prevent any excess movement of the extension column.
PAGE 9
Installation to Lightweight Suspended Ceiling Plate Refer to instruction sheet for lightweight suspended ceiling plate (CMJ 455) for attachment of ceiling plate to ceiling. Screw extension column (EXT or ADJ Series) to retaining collar in ceiling tray. Align the notch with one of the four holes in retaining collar and secure extension column with one M5 x 10 mm socket pin screw (P) using security allen wrench (G). See figure 3-8.
PAGE 10
Attaching Tilt Bracket to LCD Screen Note: This product is designed to accommodate screens with VESA® compliant hole patterns. For safe mounting, please make sure that mounting screws turn at least three complete turns in the screen inserts. FOR VESA 75 MOUNTING PATTERN: 1) Choose hole pattern indicated below. 2) Attach tilt bracket (C) to back of screen using four M4 x 10 mm screws (K) as indicated below.
PAGE 11
Installation of Screen in the Vertical Position Insert two M5 x 12 mm screws (F) into column bracket of tube assembly (A) (see figure 5-1). Leave approximately 3/16" of thread exposed (see figure 5.2). COLUMN BRACKET 3/16" EXPOSED THREAD F fig. 5-1 fig. 5-2 Hook tilt bracket (C) onto column bracket (see figure 6-1). Secure with two M5 screws (F) (see figure 6-2). Adjust tilt (20° forward and 5° back) and swivel to desired position. Tighten all screws using security allen wrench (G).
PAGE 12
Installation of Screen in the Horizontal Position Insert two M5 x 12 mm screws (F) into column bracket of tube assembly (A) (see figure 5-1). Leave approximately 3/16" of thread exposed (see figure 5-2). 3/16" EXPOSED THREAD COLUMN BRACKET fig. 5-1 F fig. 5-2 Hook tilt bracket (C) onto column bracket (see figure 6-1). Secure with two M5 screws (F) (see figure 6-2). Adjust tilt (20° forward and 5° back) and swivel to desired position. Tighten all screws using security allen wrench (G).
PAGE 13
Installation of Vertical Covers Route cords through side channels of one vertical cover (Q). Snap two vertical covers together on tube assembly (A) so that they are perpendicular to tilt bracket (C). If necessary, use a handsaw to cut vertical covers to match the length of tube assembly. Q A C SIDE CHANNELS Installation of Top Covers Snap two top covers (R) together flush with finished ceiling. Use holes in top covers to mark vertical covers (Q). Using a #46 (approx. .
PAGE 14
Installation of Tilt Covers in the Vertical Position Using a carpenter's knife, cut out any sections of tilt covers (S) necessary to allow them to snap together over vertical covers (Q) as shown in figure 9-1. Note: Cut out sections of one tilt cover should mirror cut out sections of the other. Use glue (V) on the inside edge of one of the two tilting covers (S) so that the two sides will stick together when they are connected.