Installation Manual

ManualsBrandsPeerless-AV ManualsAccessoriesFlat Panel Ceiling Mount

ISSUED: 09-27-04 SHEET #: 100-9004-7 09-28-12

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com

Features:

• Comes in two adjustable height ranges (in 1" increments): 18"-30" and

36"-48".

• -5° to +20° adjustable tilt.

• Screen can be mounted in standard position or face-down.

• Portrait or landscape orientation.

• Ceiling plate included.

• Hardware included for wood or concrete installations.

• Theft resistant security fasteners included.

• VESA

75/100 mm compliant (Non-VESA adapter offered separately).

• Comes in black or silver. LCC 36-W offered in white.

• 360° swivel action.

Installation and Assembly:

Ceiling mount for LCD screens up to 29"

Models: LCC-18, LCC-18-S, LCC-36, LCC-36-S, LCC-36-W

Patent Pending

Max UL Load Capacity: 40 lb (18.1 kg)

Summary of content (12 pages)

PAGE 1
Installation and Assembly: Ceiling mount for LCD screens up to 29" Models: LCC-18, LCC-18-S, LCC-36, LCC-36-S, LCC-36-W Patent Pending Features: • Comes in two adjustable height ranges (in 1" increments): 18"-30" and 36"-48". • • • • • -5° to +20° adjustable tilt. Screen can be mounted in standard position or face-down. Portrait or landscape orientation. Ceiling plate included. Hardware included for wood or concrete installations. • Theft resistant security fasteners included.
PAGE 2
Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.
PAGE 3
Parts List A B C D E F G H I J K L M N O P Q Description tube assembly ceiling plate tilt bracket reducer #14 x 2.5" wood screw M5 x 12 mm socket pin screw 4 mm security allen wrench concrete anchor 10-32 x 3/8" socket set screw hex wrench M4 x 10 mm socket pin screw M4 x 12 mm serrated washer head socket pin screw M4 x 20 mm socket pin screw #10-32 x 3/16" slotted set screw retaining spacer M5 x 10 mm socket pin F-type screw cable tie Qty.
PAGE 4
Installation to Wood Joist Finished Ceilings, Exposed Wood Joists, or Wood Beam Ceilings 1 Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling plate (B) with two #14 x 2.5" (6 mm x 65 mm) wood screws (E) as shown using 3/8" (10 mm) socket wrench. Tighten wood screws (E) so ceiling plate (B) is firmly attached. WARNING • Tighten wood screws so that ceiling plate is firmly attached, but do not overtighten.
PAGE 5
Installation to Concrete Ceilings 1 Drill two 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling plate (B) using two concrete anchors (H) and #14 x 2.5" wood screws (E) as shown in Illustration A and 1, 2, and 3 (below). Tighten all fasteners. CONCRETE CEILING H WARNING B • Tighten wood screws firmly, but do not overtighten. Overtightening can damage the bolt, greatly reducing its holding power. E • Never tighten in excess of 80 in • lb (9 N.M.).
PAGE 6
Installing Reducer 2 Thread reducer (D) onto tube assembly (A) until tight. Insert set screw (I) into reducer as shown in figure 2.1. Tighten screw using hex wrench (J). Note: Set screw (I) is used to jam against the threads of tube assembly to prevent any excess movement. D To adjust height of tube assembly (A), remove socket pin screw and two lock washers using 4 mm security allen wrench (G) and adjust to desired height as shown in figure 2.2. I fig. 2.1 A LOCK WASHERS SOCKET PIN SCREW A fig. 2.
PAGE 7
Flush Mount Installation 3 Screw reducer (D) into ceiling plate (B) until notch in reducer is aligned with one of the four holes in ceiling plate and set screw (I) is at least partially covered by ceiling plate as shown in figure 3.1. Secure reducer with one M5 x 10 mm F-type socket pin screw (P) using security allen wrench (G) as shown in figure 3.2. Note: Slotted set screw (N) is used to jam against the threads of the reducer to prevent any excess movement of the tube assembly (A).
PAGE 8
Installation to Extension Column 3 Screw extension column (EXT or ADJ Series) to ceiling plate (B). Align the notch with one of the four holes in the ceiling plate and secure extension column with a M5 x 10 mm socket pin screw (P) using security allen wrench (G). See figure 3.5. Note: Slotted set screw (N) is used to jam against the threads of the reducer to prevent any excess movement of the extension column.
PAGE 9
Installation to Lightweight Suspended Ceiling Plate 3 Refer to instruction sheet for lightweight suspended ceiling plate (CMJ 455) for attachment of ceiling plate to ceiling. Screw extension column (EXT or ADJ Series) to retaining collar in ceiling tray. Align the notch with one of the four holes in retaining collar and secure extension column with one M5 x 10 mm socket pin screw (P) using security allen wrench (G). See figure 3.8.
PAGE 10
Attaching Tilt Bracket to LCD Screen 4 Note: This product is designed to accommodate screens with VESA® compliant hole patterns. For safe mounting, please make sure that mounting screws turn at least three complete turns in the screen inserts. FOR VESA 75 MOUNTING PATTERN: 1) Choose hole pattern indicated below. 2) Attach tilt bracket (C) to back of screen using four M4 x 10 mm screws (K) as indicated below.
PAGE 11
Installation of Screen in the Vertical Position 5 Insert two M5 x 12 mm screws (F) into column bracket of tube assembly (A) (see figure 5.1). Leave approximately 3/16" of thread exposed (see figure 5.2). 3/16" EXPOSED THREAD COLUMN BRACKET F fig. 5.1 6 fig. 5.2 Hook tilt bracket (C) onto column bracket (see figure 6.1). Then secure with two M5 screws (F) (see figure 6.2). Adjust tilt (20° forward and 5° back) and swivel to desired position. Tighten all screws using security allen wrench (G).
PAGE 12
Installation of Screen in the Horizontal Position 5 Insert two M5 x 12 mm screws (F) into column bracket of tube assembly (A) (see figure 5.1). Leave approximately 3/16" of thread exposed (see figure 5.2). COLUMN BRACKET 3/16" EXPOSED THREAD F fig. 5.1 6 fig. 5.2 Hook tilt bracket (C) onto column bracket (see figure 6.1). Secure with two M5 screws (F) (see figure 6.2). Adjust tilt (20° forward and 5° back) and swivel to desired position. Tighten all screws using security allen wrench (G).